Biete zum Verkauf den Rotel RA-10 Verstärker.Zustand: in einem sehr guten Zustand. keine Gebrauchsspuren, technisch einwandfrei. Der RA-10 bringt Klarheit und mühelose Dynamik für Musik, die seinen bescheidenen Anspruch und Preis weit übertreffen.In einigen Fällen spricht Vieles dafür, sich auf das Wesentliche zu konzentrieren. So ein Fall ist der RA-10. Er bietet eine Leistung von 40 Watt/Kanal, ist mit vier analogen Hochpegeleingängen, einem Tapeeingang, einem Phonoeingang sowie mit allen Bedienelementen bestückt, auch einen Balanceregler, die für eine bequeme und intuitive Bedienung benötigt werden. Dieser Vollverstärker ist kein Leichtgewicht, sondern ein leistungsstarkes Gerät, dessen Elektronik für eine hochwertige Musikwiedergabe optimiert wurde. Zudem überzeugt der RA-10 mit einem reinen, dynamischen Klang und einem erstklassigen Preis-/Leistungsverhältnis. Lieferumfang:1 Rotel RA10 Verstärker1 Anschlußkabel1 Bedienungsanleitung1 OrginalverpackungPrivatverkauf keine Rücknahme keine GarantieBei Fragen gerne melden.

Rotel Intergrated Amplifier A10. Used but excellent condition Includes Power Lead, Aux Leads and Speaker Wire

Rotel Intergrated Amplifier A10. Used but excellent condition Includes Power Lead, Aux Leads and Speaker Wire

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Fantastic combination of modified, highly regarded rotel amplifiers and beautiful rosewood veneered Cura CA10 Speakers. Purchased 20 years ago and Biamped (not bridged) for 15 years until turning active 6 years ago. Cura was a British startup that made some well regarded mid priced (these were 900 in 1999) speakers. They went bankrupt after 3 years. Possibly due to the high cost of parts and exceptional cabinet quality. The CA10 were the gems in the range. The CA5s were light on base and the larger ca30s were not as cohesive. These were slightly warm but beautifully balanced. 34cm high x25cm deep x 22cm wide. The drivers are very well matched vifa (doped paper base) and seas cloth dome tweeter. Very neutral but not dry. The passive Crossover boards have been removed and drivers soldered directly to the connector with QED Quora silver anniversary (silver plated) Speaker cable and silver solder. Comes with all cabling including 2m pair of QED Quora silver anniversary Speaker cables. The Active Crossover is high quality 3 stage amplifier for each channel using specialist audio op-Amps, low noise resistors and poly film capacitors. Crossover is 2.8khz. The base and treble can be tweaked to get the optimum sound in your room and there is a volume control so this can be used as a pre-amp to control volume directly. Turning the system active tightened up the base and reduced compression at higher volumes. It was a major transformation. The Rotels have been modified on the left channel to provide the correct base shelf frequency to match the cabinet size so will not work with standard speakers. Hence selling as a system. I am an electronics graduate that specialized in HiFi Audio electrical and acoustic engineering (before everything went digital) so you can be confident it sounds really good. Selling reluctantly to make space. I have now purchased some active nearfield midrange Adams monitors to get a similar sound/Quality. Comes with all cables needed as shown in the pictures. Collection only from North Hampshire.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Fantastic combination of modified, highly regarded rotel amplifiers and beautiful rosewood veneered Cura CA10 Speakers. Purchased 20 years ago and Biamped (not bridged) for 15 years until turning active 6 years ago. Cura was a British startup that made some well regarded mid priced (these were 900 in 1999) speakers. They went bankrupt after 3 years. Possibly due to the high cost of parts and exceptional cabinet quality. The CA10 were the gems in the range. The CA5s were light on base and the larger ca30s were not as cohesive. These were slightly warm but beautifully balanced. 34cm high x25cm deep x 22cm wide. The drivers are very well matched vifa (doped paper base) and seas cloth dome tweeter. Very neutral but not dry. The passive Crossover boards have been removed and drivers soldered directly to the connector with QED Quora silver anniversary (silver plated) Speaker cable and silver solder. Comes with all cabling including 2m pair of QED Quora silver anniversary Speaker cables. The Active Crossover is high quality 3 stage amplifier for each channel using specialist audio op-Amps, low noise resistors and poly film capacitors. Crossover is 2.8khz. The base and treble can be tweaked to get the optimum sound in your room and there is a volume control so this can be used as a pre-amp to control volume directly. Turning the system active tightened up the base and reduced compression at higher volumes. It was a major transformation. The Rotels have been modified on the left channel to provide the correct base shelf frequency to match the cabinet size so will not work with standard speakers. Hence selling as a system. I am an electronics graduate that specialized in HiFi Audio electrical and acoustic engineering (before everything went digital) so you can be confident it sounds really good. Selling reluctantly to make space. I have now purchased some active nearfield midrange Adams monitors to get a similar sound/Quality. Comes with all cables needed as shown in the pictures. Collection only from North Hampshire.

EINGESTELLT MIT

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.

Rote RA 062 High Current Stereo Integrated Amplifier Outstanding Sounding Amplifier Shipped by UPS 24 - 48 Hrs Free of charge UK Only OverviewThe RA-1062 is the evolution of Rotel’s highly regarded RA-1060. The design team spent hundreds of hours evaluating individual component performance from input to output. Chief among these improvements is the UK designed and manufactured T-Network power supply capacitor. These premium grade components follow the tradition of our Slit Foil capacitors by incorporating tiny perforations in the capacitor foil to reduce distortion. Even more significantly, the T-Network capacitor has multiple connections that effectively create several smaller capacitors. within a single larger body and thus ensure far lower voltage intermodulation between input and output. The result is a striking portrayal of musical subtleties supported by a deep, well defined and accurate bass-line. The RA-1062 includes a MM phono stage with inputs for Tuner, Tape 1 and 2, CD, and Aux. A 12 volt trigger, IR remote input, speakers A & B selector, headphone output, balance control, contour switch round out the features of this superbly capable integrated amplifier. SpecificationsContinuous Power Output 60 watts/channel (20-20 kHz, < 0.03%, 8 ohms) Total Harmonic Distortion (20Hz-20kHz) < 0.03% at rated power, 1/2 power, or 1 watt Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt Frequency Response Phono Input Line Level Inputs 20Hz-15kHz, ±0.2dB 10Hz-100kHz, +1, –3dB Damping Factor (20-20,000 Hz, 8 ohms) 150 Line Input Sensitivity / Impedance 160 mV / 24 kohms Tone Control Bass Treble +3-4dB at 100 Hz +3dB at 10kHz Line Input Overload 5 V Phono (MM) Sensitivity / Impedance 2.4mV / 47 kohms Input (Phono) Overload 170 mV Preamplifier Output / Impedance 1V / 470 ohms Signal to Noise Ratio (IHF “A” weighted) >95 dB Power Requirements USA: EC: 115 Volts, 60 Hz 230 Volts, 50 HzPower Consumption 300 Watts Dimensions (W x H x D) 433 x 92 x 334mm 17 1/8 x 3 5/8 x 13 1/8 in Front Panel Height 80mm / 3 1/16 in Weight (net) 7.8 kg, 17.2 lbs.