For sale Townshend Allegri passive Pre amplifier. Good condition and amazing pre amp for money, i used Music First baby ref before, this was slight better in my system and 2/3 times cheaper :))) Townshend Allegri is an autotransformer line-level passive preamplifier designed to provide ultimate signal transparency in high-end hi-fi systems. This unit simply selects 6 inputs, adjusts gain and provides two outputs, but its beauty is in its simplicity and the sheer quality of its purist design. This is essentially a cut down version of the amazing Townshend Audio Glastonbury Pre 1 Autotransformer Preamp. The Allegri preamp has almost the same sound as the Glastonbury Pre 1, but with no remote control, mono, mute, -10dB, +1dB, balanced operation, or AC coupling. Post to all Worldwide

For sale Townshend Allegri passive Pre amplifier. Good condition and amazing pre amp for money, i used Music First baby ref before, this was slightly better in my system and 2/3 times cheaper :))) Townshend Allegri is an autotransformer line-level passive preamplifier designed to provide ultimate signal transparency in high-end hi-fi systems. This unit simply selects 6 inputs, adjusts gain and provides two outputs, but its beauty is in its simplicity and the sheer quality of its purist design. This is essentially a cut down version of the amazing Townshend Audio Glastonbury Pre 1 Autotransformer Preamp. The Allegri preamp has almost the same sound as the Glastonbury Pre 1, but with no remote control, mono, mute, -10dB, +1dB, balanced operation, or AC coupling. Post to all Worldwide

SUPERB TOWNSHEND AUDIO ALLEGRI+ PREAMPLIFIEROTHER TOWNSHEND AUDIO PRODUCTS ALSO AVAILABLE - PLEASE SEE OUR OTHER LISTINGS OR SEND A MESSAGE Free Worldwide shipping 12 months WARRANTY Any questions re. discounts, shipping etc. - please call.New Open Box MULTI AWARD WINNING Townshend Audio Allegri+ Autotransformer Passive Preamplifier, complete with original packaging plus 12 months warranty,It sports 6 RCA inputs with a front selector knob and 30 discrete gain positions on a selector knob as well. Also on the front is a useful mute switch, and a 3.5mm input for digital audio players (DAPs) in parallel with input 6 on the back panel with 2 active RCA outputs. Allegri+ is used by MAGICO and B&W Loudspeakers in their Reference systems as the master controller when voicing and setting the tonal balance of their new world class speaker ranges - chosen because its the lowest distortion, lowest noise, most natural and uncoloured sounding preamp they can find.NOW AVAILABLE TOWNSHEND AUDIO ALLEGRI REFERENCE PLEASE GET IN TOUCH FOR PRICES TOWNSHEND AUDIO ALLEGRI+Unrivalled sound quality with crystal clear treble, open mid-band and subterranean bassUltra high end performance in a small packagePurely passive Autotransformer design wired throughout with Fractal-Wire™ to perfectly match any source component with any power amplifierNo mains noise, no electronic hash and no requirement for esoteric mains conditioners or power cordThe Allegri+ Passive Autotransformer preamp is exceptionally transparent, has absolutely no noise and has enormously wide bandwidth. It has vanishingly low distortion, very powerful and deep bass and amazing drive throughout the audio band. Treble is crystal clear with not a hint of hardness or brashness. It just sounds right! The nature of the transformer design eliminates the problems usually associated with resistive passive controls. At the zero dB setting the input signal is directly connected to the output. This means that the output impedance of The Allegri+ is the same as the output impedance of the source component. Further, the input impedance of The Allegri+ is equal to the input impedance of the power amplifier at this setting. At -6dB (output voltage half the input voltage), the input impedance of The Allegri+ is four times the input impedance of the power amplifier and the output impedance of the Allegri+ is one quarter of the source impedance. At -20dB (10 to 1), the input impedance of the Allegri+ is one hundred times the power amplifier impedance and the output impedance of the Allegri+ is one hundredth of the impedance of the source component. It is thus clear that the interconnect cable capacitance will have no effect on the performance of the Allegri+. There are no coupling capacitors or active devices in the signal path in The Allegri+ and the absence of a noise-injecting power supply guarantees ultimate sound quality. The Allegri+ has a six-position input selector, a mute switch and a 24-position volume control with intervals chosen to cover a wide range of volume levels in different systems. Its state-of-the-art autotransformers are wound with Townshend Audio Fractal-Wire™ and laminated with ultra-thin mu-metal laminations for the highest possible resolution. There are six pairs of gold plated stereo phono inputs and two pairs of outputs and a 3.5mm input jack on the front panel. The case is made of anodised aluminium. Preamps of today do not require gain as all quality source components have an output of about 2 volts with a low output impedance. Any competent power amplifier will achieve full output with typically 1 volt and have a high input impedance. Unlike conventional passive controllers the Townshend Allegri+ matches the impedance requirements of source and amplifier so that full dynamics are retained. Fractal-Wire ™ results in the most accurate, uncoloured and open-sounding preamplifier possible – with astonishing transparency and resolution of fine detail. It is DC coupled with no capacitors in the signal path. It is essential to use F1 Fractal-Wire™ interconnects for both input and output of the Allegri+, so as not to compromise the profound advantage of the Fractal-Wire wound transformers. For the very best sound quality, we recommend optimising your system by using Townshend F1 Fractal™ Interconnects and F1 Fractal™ Speaker Cables. Female XLR to Phono and Phono to male XLR adaptor cables are available separately, enabling full balanced operation.Frequency response: 8Hz-100kHz +/- 0.1dBMaximum signal level: 4V RMS 8Hz; 10V RMS 20HzMaximum DC offset : 5mV. (For undistorted 8Hz)Distortion: Less than 0.01% at 400Hz, 10V (2nd and 3rd harmonic only)Input impedance is dependent upon the load impedance and gain setting. So, with a power amplifier having 20kohm input impedance (typical)Impedance: At 0dB, input impedance is 20kohm At -10dB (normal listening) input impedance is 200kInputs: 6 pairs RCA phono sockets (gold plated) One 3.5mm stereo socket on front panel.Outputs: 2 pairs RCA phono sockets (gold plated)Width: 135mm (5.3in)Height: 53mm (2.1in)Depth: 326mm (12.8in)Weight: 2kg (4.4lb)Allegri+ is used by MAGICO and B&W Loudspeakers in their Reference systems as the master controller when voicing and setting the tonal balance of their new world class speaker ranges choosen because its the lowest distortion, lowest noise, most natural and uncoloured sounding preamp they can find.Since launch the Allegri+ has received OUTSTANDING reviews and won MULTI AWARDS worldwide.Giant killing Townshend Audio Allegri+ described by Jason Kennedy. There is something about hearing extra layers of sound and effects in a complex mix. If you want to hear more of the nuance and phasing in your favorite records whatever format they may be in, then the Allegri+ is something of a bargain.... It imbues the music with extra energy that some consider to be lacking in passive devices, making the Allegri+ very engaging.POSITIVE FEEDBACKTownshend Audio Allegri+ Preamplifier: U.S.A. Premier Review From the inventor of the worlds first practical equipment and turntable isolation devices, the first practical and most utilized ribbon super tweeter, the most effective turntable/tonearm design with both isolation and active tonearm damping, and probably other firsts I am unaware of, comes the first totally passive audiophile preamp (no power cord, no tubes, no transistors). The Allegri+ is a true breakthrough design and musical triumph. At $2995 and only single-ended, its performance will captivate and thrill any listener in any system where RCA terminations are all you need.Allegri+, welcome to America!I replaced my reference E.A.R. 834L linestage, tube-rolled with NOS Mullard tubes, and connected the 6 sources to the Allegri+. I connected one output to my subwoofer and one to my E.A.R. V12 Amplifier. It sports 6 inputs addressable on a front selector knob and 30 discrete gain positions on a selector knob as well.Also on the front is a useful mute switch, and a 3.5mm input for digital audio players (DAPs)! The entire package is finished in silver, compact and elegant in every way.Specifications:Frequency response: 8Hz?100kHz +/? 0.1dBDistortion: Less than 0.01% at 400HzInput impedance: dependent upon the load impedance and gain setting.Inputs: 6 pairs of phono sockets (gold plated) plus one 3.5mm stereo socket on front panel.Outputs: 2 pairs RCA phono sockets (gold plated)Width: 5.3” Height: 2.1” Depth: 12.8”Weight: 4.4 lb. My ThoughtsIn over 50 years of audiophile exploration and music listening, I have never found a passive preamp I could abide at any price. The last one I experimented with was the pricey SMc by Steve McCormick, which was very good, but not really passive, just low gain. Before that, I listened to the Adcom 750 designed by Nelson Pass for Adcom. It had a switch which eliminated all the active circuitry and converted the unit to passive. Unfortunately, the switch also eliminated the highs and most of the impact of the music.Without buffering the output, the impedance of your source components will probably not be correct to run an amp. In this case, a typical passive line stage will sound muffled and polite. With conventional buffering of resistors/capacitors etc., you lose output rather dramatically. Since you have only a volt or two from the source, any loss is tragic to the music. I would estimate a 25% loss from typical passive setups with conventional circuitry. You cannot achieve full output from most amplifiers or extended frequency response, even, if your impedance is corrupted with conventional passive designs.Enter Townshend Allegri+. Its use of fractal wire to create the proper impedance, over 800 feet of it in this small unit, gives you perfect impedance, and only reduces the voltage from source components by about 5%, not 25%! Welcome to the 21st Century!.SummaryIt has no sound of its own. I heard no real or imaginary effect of the Allegri+ on the output. Volume and dramatic impact are unaffected. Nothing polite here. Even my 1959 Scott 350 Tuner drove my amplifier exceptionally well, as did every source I had. My Astell & Kern &ultima SP1000 connected via the 3.5 input jack in the front was fantastic with all hi-rez material. Most—maybe 95%—of the noise, colorations, golden glow, haze, crispness, and lack of musical textural nuance I blamed on the amp, was in fact the reference active preamp or my choice of cables. I switched to my best UITAudio Cables, Kubala-Sosna, and Kimber Select and WOW! Extraordinary clarity! You can hear to the rear and sides of the studio with no haze or glaze at all.Width and height of the soundstage increased significantly. In addition to extra clarity of images, distortion of every variety was reduced dramatically. This was not subtle improvement my friends. You hear MORE music with LESS grunge. I had a visiting Audio Guru over for a visit recently and played the system with the Allegri+ on board. He was shocked and stunned by the definition, musicality, and utter lack of distortion. He made it clear he needed an Allegri+ as soon as possible. I did not even give him a comparison, the performance of the Allegri+ was that fantastic.There may be a system that passive does not work. If you have a DAC with at least 2 volts output, phono stage with 2 volts out, tuners with 2 volts out, or DAC with 2 volts out, try an Allegri+. You can beat the performance of the Allegri+ with my reference E.A.R. 912 and get balanced facilities and tons of features, too.It is only $9000 more than the Allegri+. BreakthroughI would normally just call improvements to methods for reproducing music in the home an achievement or tweak. The Allegri+ is not that. The Allegri+ is a breakthrough in design as much as ultra-linear, FETs, DSD, or the like. Fractal wire impedance control is hard to implement. No one has ever tried to do it before now, or even thought about trying. All I can say is the Allegri+ is a stunning marvel for our audio age and a bargain, too.SummaryThe Townshend Audio Allegri+ Preamplifiers U.S.A. premier opens a whole new category for audiophile line stage owners: exceptionally high-quality Passive System Control. With the use of outstanding new wire technology, the Allegri+ Preamplifier is the worlds first honest-to-goodness high-end audiophile passive line stage. You have no power cord to choose, no tubes, and no transistors. With no describable sonic weaknesses or colorations, it provides a flexible controller for your finest gear to produce their true musical excellence. After months of listening I cannot and will not do without the Townshend Audio Allegri+ Preamplifier. Though it sounds like nothing at all, it allows everything else to shine! Theres nothing like this on the planet—until now.My highest recommendation!Townshend Audio Allegri+ Preamplifier Giant killing Townshend Audio Allegri+ described by Jason Kennedy.It can be all too easy to take things for granted I find, you can use something for years and fail to find anything to better it and still don’t climb to the top of the nearest tower and shout about it. But when the manufacturer makes a change to it, the option to right that wrong appears and thus it is with the Townshend Allegri passive preamplifier. I reviewed the original when it was launched some years ago, in 2008 to be exact, and was so blown away that it has remained my reference preamp ever since. There have been one or two active preamplifiers that have come close to it over that time but none that didn’t cost over 20 grand that were superior in all respects. The + is very similar to its forebear, the same but slightly bigger casework and twin knobs for input selection and volume, and the same operation principle which is that it uses an autotransformer to vary the attenuation of an incoming signal, or change volume as it’s known. The Allegri+ differs in functionality by the addition of a mute switch and a front panel input on a minijack, and in appearance by better finishing and knurling on the knobs. The only really fundamental way it has changed is the way that Townshend apply a proprietary process to the copper within the transformers and the wires that connect the whole thing. The Fractal-Wire that Townshend develop is now processed in teh UK rather than the US as was previously the case, a move that company founder and engineer Max Townshend says is superior to the earlier one. But he would say that would he not!In an autotransformer passive the in- and output impedances vary with level such that the source and power amplifier are automatically matched with one another, which in practise means very high transparency with no barriers to dynamics. It also means that cable capacitance doesn’t effect performance as it does with some passive designs. The volume control has 24 positions with a -52B minimum and 0dB maximum, the size of the steps between each position vary with the smallest 1dB steps between positions 11 and 19. Whether this is the area you end up operating within depends largely on the sensitivity of your loudspeakers and how loud you want the music, I found myself using the lower part of the range where the level changes are bigger.Being passive the Allegri+ is DC coupled with no capacitors in the signal path, it is not a straight wire with gain but a straight wire with variable attenuation, albeit quite a long wire wound around a bobbin. It remains compact and bijou with space for six line inputs and two outputs on the rear and a slimline case that’s heavy enough to hold its own against the mass of that many cables but small enough to pack in your overnight bag.I have used the Allegri+ for long enough now to appreciate that it is just as transparent, tonally neutral and wide in bandwidth as its predecessor, probably a little more so in fact. Which means that you can hear pretty well everything that the source sends to it, regardless of whether that source is a streamer, a phono stage or a DAC, and that makes the job of reviewing a lot easier. It also makes listening to your favourite music a totally immersive and fabulous experience. I have used other transformer passives in the past but while they can have a smoother more refined character they do not offer the bass extension or the sheer detail resolution of the Allegri+. The Townshend does nothing to polish or sweeten the sound, it gives it to you just the way it is and if you’re after maximum fidelity that’s the way it should be. Take a look through my source component reviews on this site and beyond and you’ll see that the results have often been exemplary, totally engaging and revealing. That’s because nigh on all of them have been reviewed with an Allegri+, a preamplifier that allows any source to reveal its true colours whatever they may be. That also includes the many products that have onboard volume controls, which when it comes to DACs in particular is legion. It has been a very rare occasion indeed to find that the Allegri+ has not sounded better than connecting that product directly to the power amplifier. There is a theoretical advantage in eliminating an interconnect and the wiring of the autotransformer and selector switch but this is virtually always outweighed by the relative quality of attenuation between the source and the Allegri+. Bypassing the volume control in most sources and using this preamp results in a more open and dynamic sound with greater transparency to fine detail. Openness is one area where I have not found its equal, it’s almost as if it’s a characteristic of the Allegri+, but the scale of differences between recordings suggests that it is just better at allowing that aspect of the signal to get to the power amp than most other preamps.The Allegri+ is genuinely devoid of the characteristics and colourations that are found with the vast majority of preamplifiers, which all add something to the signal by comparison. With transistor designs it’s hard to get away from the fine grain that amplification tends to add, basically the presence of electric current overlays itself on the signal and unless the power supply is uncannily good this can be heard. Tube preamps tend to be more obvious and have a warmth that the harmonic distortion of the devices adds, it’s a nice and often harmonious colouration but it’s still a change. Auto transformers are not without their shortcomings of course but they seem to be smaller than those in active preamps and less obvious than other passive designs. The Allegri+’s only shortcoming is that you have to get off the sofa to change volume, which is good for your health of course but a chore nonetheless. Townshend has created the Enigma to provide this and other facilities but it’s rather more expensive as a result. The other minor complaint is that the inputs are a little close for the chunkier variety of RCA plugs, it’s a small back plate so this is hard to get around without losing an input but if you have a lot of sources and hardcore RCAs it’s a consideration.But these are the strongest criticisms I can come up with in the context of a preamplifier that has few peers and none to my knowledge at anywhere near the same price. And that’s before we get to timing, this aspect of music reproduction is very, very important when it comes to recreating an engaging, true to life result with recorded music and the Allegri+ gets it bang on every time. It doesn’t matter what type of music is involved the notes stop and start precisely as the source dictates, with no added smear or overhang.I believe the Townshend Allegri+ represents incredible value for money in sound quality terms, it’s not big and shiny but it is capable of truly transcendent results of that few preamplifiers are equal to. For this reason the Allegri+ warrants a greater recommendation than our Best Buy and Five Star awards, this product and a very few select others warrant an Editor’s Choice, an indication that it is the best product in its class at the time of review. Dan Worth and Dom Marsh HiFi Pig awarded Allegri+ OUTSTANDING PRODUCTUnrivaled sound quality with crystal clear treble, open mid-band and subterranean bass,Ultra high end performance in a small packagePurely passive Autotransformer design wired throughout with Fractal-wire to perfectly match any source component with any power amplifier,No mains noise, no electronic hash and no requirement for esoteric mains conditioners or power cables.Please read full review at HiFi Pighttps://hifipig.com/townshend-allegri-passive-preamplifier/

Hallo,hier wird ein Townshend Audio Allegri Preamplifier Vorverstärker angeboten,das Gerät funktioniert und ist in einem guten Zustand ! Privatverkauf: Verkauf erfolgt von privat unter Ausschluss von Gewährleistung, Garantie, keine Rücknahme und Umtausch.

Hallo,hier wird ein Townshend Audio Allegri Preamplifier Vorverstärker angeboten,das Gerät funktioniert und ist in einem guten Zustand ! Privatverkauf: Verkauf erfolgt von privat unter Ausschluss von Gewährleistung, Garantie, keine Rücknahme und Umtausch.

100% Authentic! All packages are shipped directly from Japan!Condition DescriptionFeatures and Remarks Very clear, noiseless, very wide bandwidth. Features/Remarks Powerful and bass-heavy, with drive felt throughout the entire bandwidth. High frequency range is very clear. Accessories Manual Please Note shipping from Japan. Policy PaymentYou can use various payment methods based on eBay Managed Payments. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

DescriptionAuthenticity: 100% AUTHENTIC! If you have any question about the condition, accessories, or anything about the product,Please feel free to message us. We are glad to answer all your concerns. ShippingDHL, Fedex Fastshipping3-10 business days after shipment(Tracking number + Insurance.)PaymentPlease give me the payment within 3days from the date of bid.About UsWe sell our items on other websites and in our retail stores in Japan at the same time.If the item was sold out before your purchase, your order will be cancelled and a full refund will be issued immediately. International Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior. Thank you.

We have this preowned Townshend Allegri+ passive preamplifier in the silver finish. It is in very good condition with some very minor cosmetic marks and scratches which can be seen in the pictures attached. The unit comes with its user manual and original packaging. £20 Mainland UK Delivery Any queries please do not hesitate to contact us. TI-1-64521-911009 Auction items can be viewed and demoed if practical at our demo rooms in Hull, please make an appointment in advance. Fanthorpes Hifi is based in a stunning Edwardian Arcade in Hull East Yorkshire. There are no pressure sales, we only sell the brands we believe in and always put the customer first. We are specialists in CHORD, PMC, Bryston, Devialet, Arcam, Musical Fidelity, Martin Logan amongst others please check our website for more details. HS

Townshend Allegri+ Autotransformer Pre-Amplifier Stereo Control UnitImmaculate condition Bought new in March 2021Current new price is £2500Comes complete with aluminium case and instructionsReview and details here:https://www.hifipig.com/townshend-allegri-passive-/preamplifier Any questions, message me on 07900910511 Track Page Views WithAuctivas Counter

SUPERB TOWNSHEND AUDIO ALLEGRI+ PREAMPLIFIEROTHER TOWNSHEND AUDIO PRODUCTS ALSO AVAILABLE - PLEASE SEE OUR OTHER LISTINGS OR SEND A MESSAGE Free Worldwide shipping 12 months WARRANTY Any questions re. discounts, shipping etc. - please call.New Open Box MULTI AWARD WINNING Townshend Audio Allegri+ Autotransformer Passive Preamplifier, complete with original packaging plus 12 months warranty,It sports 6 RCA inputs with a front selector knob and 30 discrete gain positions on a selector knob as well. Also on the front is a useful mute switch, and a 3.5mm input for digital audio players (DAPs) in parallel with input 6 on the back panel with 2 active RCA outputs. Allegri+ is used by MAGICO and B&W Loudspeakers in their Reference systems as the master controller when voicing and setting the tonal balance of their new world class speaker ranges - chosen because its the lowest distortion, lowest noise, most natural and uncoloured sounding preamp they can find.NOW AVAILABLE TOWNSHEND AUDIO ALLEGRI REFERENCE PLEASE GET IN TOUCH FOR PRICES TOWNSHEND AUDIO ALLEGRI+Unrivalled sound quality with crystal clear treble, open mid-band and subterranean bassUltra high end performance in a small packagePurely passive Autotransformer design wired throughout with Fractal-Wire™ to perfectly match any source component with any power amplifierNo mains noise, no electronic hash and no requirement for esoteric mains conditioners or power cordThe Allegri+ Passive Autotransformer preamp is exceptionally transparent, has absolutely no noise and has enormously wide bandwidth. It has vanishingly low distortion, very powerful and deep bass and amazing drive throughout the audio band. Treble is crystal clear with not a hint of hardness or brashness. It just sounds right! The nature of the transformer design eliminates the problems usually associated with resistive passive controls. At the zero dB setting the input signal is directly connected to the output. This means that the output impedance of The Allegri+ is the same as the output impedance of the source component. Further, the input impedance of The Allegri+ is equal to the input impedance of the power amplifier at this setting. At -6dB (output voltage half the input voltage), the input impedance of The Allegri+ is four times the input impedance of the power amplifier and the output impedance of the Allegri+ is one quarter of the source impedance. At -20dB (10 to 1), the input impedance of the Allegri+ is one hundred times the power amplifier impedance and the output impedance of the Allegri+ is one hundredth of the impedance of the source component. It is thus clear that the interconnect cable capacitance will have no effect on the performance of the Allegri+. There are no coupling capacitors or active devices in the signal path in The Allegri+ and the absence of a noise-injecting power supply guarantees ultimate sound quality. The Allegri+ has a six-position input selector, a mute switch and a 24-position volume control with intervals chosen to cover a wide range of volume levels in different systems. Its state-of-the-art autotransformers are wound with Townshend Audio Fractal-Wire™ and laminated with ultra-thin mu-metal laminations for the highest possible resolution. There are six pairs of gold plated stereo phono inputs and two pairs of outputs and a 3.5mm input jack on the front panel. The case is made of anodised aluminium. Preamps of today do not require gain as all quality source components have an output of about 2 volts with a low output impedance. Any competent power amplifier will achieve full output with typically 1 volt and have a high input impedance. Unlike conventional passive controllers the Townshend Allegri+ matches the impedance requirements of source and amplifier so that full dynamics are retained. Fractal-Wire ™ results in the most accurate, uncoloured and open-sounding preamplifier possible – with astonishing transparency and resolution of fine detail. It is DC coupled with no capacitors in the signal path. It is essential to use F1 Fractal-Wire™ interconnects for both input and output of the Allegri+, so as not to compromise the profound advantage of the Fractal-Wire wound transformers. For the very best sound quality, we recommend optimising your system by using Townshend F1 Fractal™ Interconnects and F1 Fractal™ Speaker Cables. Female XLR to Phono and Phono to male XLR adaptor cables are available separately, enabling full balanced operation.Frequency response: 8Hz-100kHz +/- 0.1dBMaximum signal level: 4V RMS 8Hz; 10V RMS 20HzMaximum DC offset : 5mV. (For undistorted 8Hz)Distortion: Less than 0.01% at 400Hz, 10V (2nd and 3rd harmonic only)Input impedance is dependent upon the load impedance and gain setting. So, with a power amplifier having 20kohm input impedance (typical)Impedance: At 0dB, input impedance is 20kohm At -10dB (normal listening) input impedance is 200kInputs: 6 pairs RCA phono sockets (gold plated) One 3.5mm stereo socket on front panel.Outputs: 2 pairs RCA phono sockets (gold plated)Width: 135mm (5.3in)Height: 53mm (2.1in)Depth: 326mm (12.8in)Weight: 2kg (4.4lb)Allegri+ is used by MAGICO and B&W Loudspeakers in their Reference systems as the master controller when voicing and setting the tonal balance of their new world class speaker ranges choosen because its the lowest distortion, lowest noise, most natural and uncoloured sounding preamp they can find.Since launch the Allegri+ has received OUTSTANDING reviews and won MULTI AWARDS worldwide.Giant killing Townshend Audio Allegri+ described by Jason Kennedy. There is something about hearing extra layers of sound and effects in a complex mix. If you want to hear more of the nuance and phasing in your favorite records whatever format they may be in, then the Allegri+ is something of a bargain.... It imbues the music with extra energy that some consider to be lacking in passive devices, making the Allegri+ very engaging.POSITIVE FEEDBACKTownshend Audio Allegri+ Preamplifier: U.S.A. Premier Review From the inventor of the worlds first practical equipment and turntable isolation devices, the first practical and most utilized ribbon super tweeter, the most effective turntable/tonearm design with both isolation and active tonearm damping, and probably other firsts I am unaware of, comes the first totally passive audiophile preamp (no power cord, no tubes, no transistors). The Allegri+ is a true breakthrough design and musical triumph. At $2995 and only single-ended, its performance will captivate and thrill any listener in any system where RCA terminations are all you need.Allegri+, welcome to America!I replaced my reference E.A.R. 834L linestage, tube-rolled with NOS Mullard tubes, and connected the 6 sources to the Allegri+. I connected one output to my subwoofer and one to my E.A.R. V12 Amplifier. It sports 6 inputs addressable on a front selector knob and 30 discrete gain positions on a selector knob as well.Also on the front is a useful mute switch, and a 3.5mm input for digital audio players (DAPs)! The entire package is finished in silver, compact and elegant in every way.Specifications:Frequency response: 8Hz?100kHz +/? 0.1dBDistortion: Less than 0.01% at 400HzInput impedance: dependent upon the load impedance and gain setting.Inputs: 6 pairs of phono sockets (gold plated) plus one 3.5mm stereo socket on front panel.Outputs: 2 pairs RCA phono sockets (gold plated)Width: 5.3” Height: 2.1” Depth: 12.8”Weight: 4.4 lb. My ThoughtsIn over 50 years of audiophile exploration and music listening, I have never found a passive preamp I could abide at any price. The last one I experimented with was the pricey SMc by Steve McCormick, which was very good, but not really passive, just low gain. Before that, I listened to the Adcom 750 designed by Nelson Pass for Adcom. It had a switch which eliminated all the active circuitry and converted the unit to passive. Unfortunately, the switch also eliminated the highs and most of the impact of the music.Without buffering the output, the impedance of your source components will probably not be correct to run an amp. In this case, a typical passive line stage will sound muffled and polite. With conventional buffering of resistors/capacitors etc., you lose output rather dramatically. Since you have only a volt or two from the source, any loss is tragic to the music. I would estimate a 25% loss from typical passive setups with conventional circuitry. You cannot achieve full output from most amplifiers or extended frequency response, even, if your impedance is corrupted with conventional passive designs.Enter Townshend Allegri+. Its use of fractal wire to create the proper impedance, over 800 feet of it in this small unit, gives you perfect impedance, and only reduces the voltage from source components by about 5%, not 25%! Welcome to the 21st Century!.SummaryIt has no sound of its own. I heard no real or imaginary effect of the Allegri+ on the output. Volume and dramatic impact are unaffected. Nothing polite here. Even my 1959 Scott 350 Tuner drove my amplifier exceptionally well, as did every source I had. My Astell & Kern &ultima SP1000 connected via the 3.5 input jack in the front was fantastic with all hi-rez material. Most—maybe 95%—of the noise, colorations, golden glow, haze, crispness, and lack of musical textural nuance I blamed on the amp, was in fact the reference active preamp or my choice of cables. I switched to my best UITAudio Cables, Kubala-Sosna, and Kimber Select and WOW! Extraordinary clarity! You can hear to the rear and sides of the studio with no haze or glaze at all.Width and height of the soundstage increased significantly. In addition to extra clarity of images, distortion of every variety was reduced dramatically. This was not subtle improvement my friends. You hear MORE music with LESS grunge. I had a visiting Audio Guru over for a visit recently and played the system with the Allegri+ on board. He was shocked and stunned by the definition, musicality, and utter lack of distortion. He made it clear he needed an Allegri+ as soon as possible. I did not even give him a comparison, the performance of the Allegri+ was that fantastic.There may be a system that passive does not work. If you have a DAC with at least 2 volts output, phono stage with 2 volts out, tuners with 2 volts out, or DAC with 2 volts out, try an Allegri+. You can beat the performance of the Allegri+ with my reference E.A.R. 912 and get balanced facilities and tons of features, too.It is only $9000 more than the Allegri+. BreakthroughI would normally just call improvements to methods for reproducing music in the home an achievement or tweak. The Allegri+ is not that. The Allegri+ is a breakthrough in design as much as ultra-linear, FETs, DSD, or the like. Fractal wire impedance control is hard to implement. No one has ever tried to do it before now, or even thought about trying. All I can say is the Allegri+ is a stunning marvel for our audio age and a bargain, too.SummaryThe Townshend Audio Allegri+ Preamplifiers U.S.A. premier opens a whole new category for audiophile line stage owners: exceptionally high-quality Passive System Control. With the use of outstanding new wire technology, the Allegri+ Preamplifier is the worlds first honest-to-goodness high-end audiophile passive line stage. You have no power cord to choose, no tubes, and no transistors. With no describable sonic weaknesses or colorations, it provides a flexible controller for your finest gear to produce their true musical excellence. After months of listening I cannot and will not do without the Townshend Audio Allegri+ Preamplifier. Though it sounds like nothing at all, it allows everything else to shine! Theres nothing like this on the planet—until now.My highest recommendation!Townshend Audio Allegri+ Preamplifier Giant killing Townshend Audio Allegri+ described by Jason Kennedy.It can be all too easy to take things for granted I find, you can use something for years and fail to find anything to better it and still don’t climb to the top of the nearest tower and shout about it. But when the manufacturer makes a change to it, the option to right that wrong appears and thus it is with the Townshend Allegri passive preamplifier. I reviewed the original when it was launched some years ago, in 2008 to be exact, and was so blown away that it has remained my reference preamp ever since. There have been one or two active preamplifiers that have come close to it over that time but none that didn’t cost over 20 grand that were superior in all respects. The + is very similar to its forebear, the same but slightly bigger casework and twin knobs for input selection and volume, and the same operation principle which is that it uses an autotransformer to vary the attenuation of an incoming signal, or change volume as it’s known. The Allegri+ differs in functionality by the addition of a mute switch and a front panel input on a minijack, and in appearance by better finishing and knurling on the knobs. The only really fundamental way it has changed is the way that Townshend apply a proprietary process to the copper within the transformers and the wires that connect the whole thing. The Fractal-Wire that Townshend develop is now processed in teh UK rather than the US as was previously the case, a move that company founder and engineer Max Townshend says is superior to the earlier one. But he would say that would he not!In an autotransformer passive the in- and output impedances vary with level such that the source and power amplifier are automatically matched with one another, which in practise means very high transparency with no barriers to dynamics. It also means that cable capacitance doesn’t effect performance as it does with some passive designs. The volume control has 24 positions with a -52B minimum and 0dB maximum, the size of the steps between each position vary with the smallest 1dB steps between positions 11 and 19. Whether this is the area you end up operating within depends largely on the sensitivity of your loudspeakers and how loud you want the music, I found myself using the lower part of the range where the level changes are bigger.Being passive the Allegri+ is DC coupled with no capacitors in the signal path, it is not a straight wire with gain but a straight wire with variable attenuation, albeit quite a long wire wound around a bobbin. It remains compact and bijou with space for six line inputs and two outputs on the rear and a slimline case that’s heavy enough to hold its own against the mass of that many cables but small enough to pack in your overnight bag.I have used the Allegri+ for long enough now to appreciate that it is just as transparent, tonally neutral and wide in bandwidth as its predecessor, probably a little more so in fact. Which means that you can hear pretty well everything that the source sends to it, regardless of whether that source is a streamer, a phono stage or a DAC, and that makes the job of reviewing a lot easier. It also makes listening to your favourite music a totally immersive and fabulous experience. I have used other transformer passives in the past but while they can have a smoother more refined character they do not offer the bass extension or the sheer detail resolution of the Allegri+. The Townshend does nothing to polish or sweeten the sound, it gives it to you just the way it is and if you’re after maximum fidelity that’s the way it should be. Take a look through my source component reviews on this site and beyond and you’ll see that the results have often been exemplary, totally engaging and revealing. That’s because nigh on all of them have been reviewed with an Allegri+, a preamplifier that allows any source to reveal its true colours whatever they may be. That also includes the many products that have onboard volume controls, which when it comes to DACs in particular is legion. It has been a very rare occasion indeed to find that the Allegri+ has not sounded better than connecting that product directly to the power amplifier. There is a theoretical advantage in eliminating an interconnect and the wiring of the autotransformer and selector switch but this is virtually always outweighed by the relative quality of attenuation between the source and the Allegri+. Bypassing the volume control in most sources and using this preamp results in a more open and dynamic sound with greater transparency to fine detail. Openness is one area where I have not found its equal, it’s almost as if it’s a characteristic of the Allegri+, but the scale of differences between recordings suggests that it is just better at allowing that aspect of the signal to get to the power amp than most other preamps.The Allegri+ is genuinely devoid of the characteristics and colourations that are found with the vast majority of preamplifiers, which all add something to the signal by comparison. With transistor designs it’s hard to get away from the fine grain that amplification tends to add, basically the presence of electric current overlays itself on the signal and unless the power supply is uncannily good this can be heard. Tube preamps tend to be more obvious and have a warmth that the harmonic distortion of the devices adds, it’s a nice and often harmonious colouration but it’s still a change. Auto transformers are not without their shortcomings of course but they seem to be smaller than those in active preamps and less obvious than other passive designs. The Allegri+’s only shortcoming is that you have to get off the sofa to change volume, which is good for your health of course but a chore nonetheless. Townshend has created the Enigma to provide this and other facilities but it’s rather more expensive as a result. The other minor complaint is that the inputs are a little close for the chunkier variety of RCA plugs, it’s a small back plate so this is hard to get around without losing an input but if you have a lot of sources and hardcore RCAs it’s a consideration.But these are the strongest criticisms I can come up with in the context of a preamplifier that has few peers and none to my knowledge at anywhere near the same price. And that’s before we get to timing, this aspect of music reproduction is very, very important when it comes to recreating an engaging, true to life result with recorded music and the Allegri+ gets it bang on every time. It doesn’t matter what type of music is involved the notes stop and start precisely as the source dictates, with no added smear or overhang.I believe the Townshend Allegri+ represents incredible value for money in sound quality terms, it’s not big and shiny but it is capable of truly transcendent results of that few preamplifiers are equal to. For this reason the Allegri+ warrants a greater recommendation than our Best Buy and Five Star awards, this product and a very few select others warrant an Editor’s Choice, an indication that it is the best product in its class at the time of review. Dan Worth and Dom Marsh HiFi Pig awarded Allegri+ OUTSTANDING PRODUCTUnrivaled sound quality with crystal clear treble, open mid-band and subterranean bass,Ultra high end performance in a small packagePurely passive Autotransformer design wired throughout with Fractal-wire to perfectly match any source component with any power amplifier,No mains noise, no electronic hash and no requirement for esoteric mains conditioners or power cables.Please read full review at HiFi Pighttps://hifipig.com/townshend-allegri-passive-preamplifier/

Townshend Allegri Reference Preamplifier in excellent condition in original flightcase and packaging.Have a look on the web many great reviews as one of the best preamps. Martin Colloms of Hi fi Critic magazine uses one as his reference and i think Jason Kennedy of the Ear publication uses it as his go to pre amp.For the avoidance of doubt this is the mark 1 version which can be upgraded i understand by Townshend themselves. It is not exactly clear what the the mark 2 improvements are, and all reviews are of the mark 1. Current RRP of these are circa £12k Any questions please ask

Townshend Allegri+ Passive Pre Amplifier, very good condition, 3 month warranty Townshend Allegri+ Passive Pre Amplifier, very good condition, 3 month warranty Here we have an example of Max Townshend’s superb passive pre-amp The Allegri+. It is in very good condition with just a small blemish on the front see photographs and comes in its original hard case packaging along with our standard 3 month warranty. Townshend Audio Says…. Unrivalled sound quality with crystal clear treble, open mid-band and subterranean bass Ultra high end performance in a small package Purely passive Autotransformer design wired throughout with Fractal-Wire™ to perfectly match any source component with any power amplifier No mains noise, no electronic hash and no requirement for esoteric mains conditioners or power cord The Allegri+ Passive Autotransformer preamp is exceptionally transparent, has absolutely no noise and has enormously wide bandwidth. It has vanishingly low distortion, very powerful and deep bass and amazing drive throughout the audio band. Treble is crystal clear with not a hint of hardness or brashness. It just sounds right! The nature of the transformer design eliminates the problems usually associated with resistive passive controls. At the zero dB setting the input signal is directly connected to the output. This means that the output impedance of The Allegri+ is the same as the output impedance of the source component. Further, the input impedance of The Allegri+ is equal to the input impedance of the power amplifier at this setting. At -6dB (output voltage half the input voltage), the input impedance of The Allegri+ is four times the input impedance of the power amplifier and the output impedance of the Allegri+ is one quarter of the source impedance. At -20dB (10 to 1), the input impedance of the Allegri+ is one hundred times the power amplifier impedance and the output impedance of the Allegri+ is one hundredth of the impedance of the source component. It is thus clear that the interconnect cable capacitance will have no effect on the performance of the Allegri+. There are no coupling capacitors or active devices in the signal path in The Allegri+ and the absence of a noise-injecting power supply guarantees ultimate sound quality. The Allegri+ has a six-position input selector, a mute switch and a 24-position volume control with intervals chosen to cover a wide range of volume levels in different systems. Its state-of-the-art autotransformers are wound with Townshend Audio Fractal-Wire™ and laminated with ultra-thin mu-metal laminations for the highest possible resolution. There are six pairs of gold plated stereo phono inputs and two pairs of outputs and a 3.5mm input jack on the front panel. The case is made of anodised aluminium. Preamps of today do not require gain as all quality source components have an output of about 2 volts with a low output impedance. Any competent power amplifier will achieve full output with typically 1 volt and have a high input impedance. Unlike conventional passive controllers the Townshend Allegri+ matches the impedance requirements of source and amplifier so that full dynamics are retained. Fractal-Wire ™ results in the most accurate, uncoloured and open-sounding preamplifier possible – with astonishing transparency and resolution of fine detail. It is DC coupled with no capacitors in the signal path. It is essential to use F1 Fractal-Wire™ interconnects for both input and output of the Allegri+, so as not to compromise the profound advantage of the Fractal-Wire wound transformers. For the very best sound quality, we recommend optimising your system by using Townshend F1 Fractal™ Interconnects and F1 Fractal™ Speaker Cables. Female XLR to Phono and Phono to male XLR adaptor cables are available separately, enabling full balanced operation. Specifications: Frequency response: 8Hz-100kHz +/- 0.1dB Maximum signal level: 4V RMS 8Hz; 10V RMS 20Hz Maximum DC offset : 5mV. (For undistorted 8Hz) Distortion: Less than 0.01% at 400Hz, 10V (2nd and 3rd harmonic only) Impedance: At 0dB, input impedance is 20kohm; At -10dB (normal listening) input impedance is 200k Inputs: 6 pairs RCA phono sockets (gold plated); One 3.5mm stereo socket on front panel. Outputs: 2 pairs RCA phono sockets (gold plated) Dimensions: 135 (W) x 326 (D) x 53 (H) mm Weight: 2kg Manufacturer : Townshend Model : Allegri+ Passive Serial Number : 178 Packaging : Original Accessories Included : N/A Price When New : ? Shipping Shipping cost:Please contact us or check listing info. If you are outside the UK you will need a shipping quote BEFORE buying. Delivery time:48 hours Payment We accept the following payment methods: Paypal Credit/Debit Card BACS Please contact us if you have any questions. Service Established in 2003, 2ndhandhifi is the UKs largest stockist of used quality audio equipment. All items are checked before despatch and guaranteed for 30 days for ebay buyers to give you peace of mind that the item will arrive safely and work exactly as per ebay descriiptions. This means that all items described as used will be in good working order but may show minimal cosmetic marks resulting from everyday use. Any more significant cosmetic issues will be highlighted in the listing if present. We accept most payment methods but card payment to our shop is preferred. We use a reputable overnight courier service - items will be despatched next working day for delivery the next working day after that, but you are welcome to collect from our sister shop in Stockton on Tees if you prefer. Check our feedback if you have any doubts about the validity of this auction or us! We are a business so (although most times we do) we cannot always answer emails over the weekend so please try to ask Monday to Friday. Important 1. If there is no buy it now price stated, please dont ask - it is intended to be an auction which will run until its end time. 2. If you are outside the UK mainland please ask us for a shipping quote BEFORE placing a bid or clicking “Buy it Now”. If you dont ask, it means you will accept our quote. We do not cut corners on shipping, we only use reliable shipping companies, and we dont profit from the shipping prices we quote. 3. For any item where there is no original packaging the shipping costs include the cost to package the item to ensure safe delivery. Larger items may be shipped on a pallet - but this usually will be stated in the listing. 4. If you win the auction or buy the item, we expect you to pay and we will issue a non payment against you if you dont. Such auctions/listings cost us time (and therefore money). Requests to cancel will be rejected.