This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This NAD C315BEE has been fitted with a new Balance Potentiometer (Dual MN Taper) and a suitable small knob to fit its knurled shaft. All of the other components are original except as below; I upgraded the Speaker Relay. The original relay had become intermittent on one channel.. Ive upgraded the audio capacitors to nichicon FW and Fine Gold, with Rubycon at the Preamp Outputs. The Power Supply Main caps have been upgraded to 63V nichicon, while the others are Panasonic, Chemicon, etc. For added versatility, I have repurposed the (fixed line level) Tape Output RCA Jacks to be (variable level) Preamp Outputs suitable for a powered Subwoofer, external Power Amp, etc. Im also including a new 6-button learning remote programmed for Mute On/Off, Volume Up/Down, and 3 Input Selects DISC, CD, and AUX. I can reprogram as requested. Cosmetically, this unit is in excellent shape except for 2 small cracks in the front panel near the volume control. They are a bit hard to see or photograph under normal lighting. Please see photos. Full refund within 60 days. Buyer pays return shipping. Please message me with any questions, corrections, etc. ******* Chapter Two ******* The NAD C315BEE is a surprisingly powerful Integrated Amp disguised as the entry level NAD C series model. Rated at 40 NAD watts per channel, the 45 Volt Main Rails and 10,000uF Main Caps provide plenty of IHF Power as well. While the reviewers are quite complimentary of this model, some have mentioned their desire for Preamp Outputs which this customized unit provides. It should be noted that the Standby Mode draws similar power and generates similar heat to the ON Mode. I recommend turning OFF the Main Switch on the Rear Panel when not in use.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

NAD Verstärker NAD C 316BEE V2 - B-Ware - Aussteller - Super Verstärker Gewährleistung bis 04.04.2027 NAD C 316BEE V2Klirrfaktor (20 Hz – 20 kHz) <0,03 % an 300 Ohm bei 2 V Ausgangssignal Geräuschspannungsabstand >100 dB (A-gewichtet, 32 Ohm, 2 V Ausgangssignal, Verstärkungsfaktor Eins) Frequenzgang ±0,3 dB (20 Hz – 20 kHz) Ausgangsimpedanz 8 Ohm Dauerausgangsleistung an 8 und 4 Ohm 2 x 40 W (20 Hz-20 kHz bei angegebenem Klirrfaktor, beide Kanäle angesteuert) Klirrfaktor (20 Hz – 20 kHz) <0.03 % (250 mW bis 40 W, 8 und 4 Ohm) Geräuschspannungsabstand >95 dB (A-gewichtet, 500 mV Eingang, 1 W Ausgang an 8 Ohm) >97 dB (A-gewichtet, 500 mV Eingang, Verstärkungsfaktor Eins an 32 Ohm) Clipping-Leistung (bei 1 kHz 0,1 % Klirrfaktor) >45 W an 8 Ohm >60 W an 4 Ohm Impulsleistung 2 x 90 W an 8 Ohm 2 x 120 W an 4 Ohm 2 x 170 W an 2 Ohm Dämpfungsfaktor >200 (8 Ohm, 1 kHz) Frequenzgang ±0,3 dB (20 Hz – 20 kHz, Klangregelung abgeschaltet) Höhen: ± 5 dB bei 10 kHz Bässe: ± 8 dB bei 100 Hz Kanaltrennung >70 dB (1 kHz) Maximaler Eingangspegel 4,3 V (1 kHz, Klirrfaktor 0,1 %) Eingangsempfindlichkeit (für 40 W an 8 Ohm) 200 mV Standby-Stromverbrauch <0,5 W Klirrfaktor (20 Hz – 20 kHz) <0,03 % (1 W an 40 W, 8 und 4 Ohm) Geräuschspannungsabstand >75 dB mit IHF MM Abtaster (A-gewichtet, 5 mV Eingang 1 kHz und 1 W Ausgang an 8 Ohm) Frequenzgang (RIAA Entzerrung) +0,3 dB (20 Hz – 20 kHz, Klangregelung abgeschaltet) Maximaler Eingangspegel 71 mV (1 kHz, Klirrfaktor 0,1 %) Eingangsempfindlichkeit (für 40 W an 8 Ohm) 2,95 mV Abmessungen (B x H x T) 435 x 90 x 285 mm Gewicht 5,5 kg

This NAD C315BEE has been fitted with a new Balance Potentiometer (Dual MN Taper) and a suitable small knob to fit its knurled shaft. All other components are original except as below; I replaced the Speaker Relay and series resistor. The original relay often becomes intermittent over time, so its best to replace it as a preventative measure. Ive upgraded the audio capacitors to nichicon FW and Fine Gold, with Rubycon at the Preamp Outputs. The Power Supply Main caps have been upgraded to 63V nichicon, while the others are Panasonic, Chemicon, etc. For added versatility, I have repurposed the (fixed line level) Tape Output RCA Jacks to be the (variable level) Preamp Outputs suitable for a powered Subwoofer, external Power Amp, etc. Im also including a new 6-button learning remote programmed for Mute On/Off, Volume Up/Down, and 3 Input Selects DISC, CD, and AUX. I can reprogram as requested. Cosmetically, this unit is in excellent shape inside and out. Please see photos. Full refund within 60 days. Buyer pays return shipping. Please message me with any questions, corrections, etc. ******* Chapter Two ******* The NAD C315BEE is a surprisingly powerful Integrated Amp disguised as the entry level NAD C series model. Rated at 40 NAD watts per channel, the 45 Volt Main Rails and 10,000uF Main Caps indicate plenty of IHF Power as well. While the reviewers are quite complimentary of this model, some have mentioned their desire for Preamp Outputs which this customized unit provides. It should be noted that the Standby Mode draws similar power and generates similar heat to the ON Mode. I recommend turning OFF the Main Switch on the Rear Panel when not in use.

We use a 48 hour courier service but please allow up to 3 days handling time as a lot of our items are large and timeconsuming to package. Many thanks :) fully working and tested.Practically unmarked. great soudning, and the phono stage is particularly good. MM & MC phono no evident operaional issues. SpecificationsPower output: 30 watts per channel into 8? (stereo)Frequency response: 20Hz to 20kHzTotal harmonic distortion: 0.03%Input sensitivity: 0.2mV (MC), 2.5mV (MM), 150mV (line)Signal to noise ratio: 76dB (MC), 76dB (MM), 85dB (line)Dimensions: 420 x 108 x 381mmWeight: 6.9kgYear: 1985 Please inspect the pictures (please also use the zoom function on the photos) and be sure of what you are buying, please don’t buy this if you are at all unsure, I will answer any questions you have, just email BEFORE PURCHASING. This is a used item and has been fairly described to the best of our ability, it has not been serviced by us, just described in it’s current operational and cosmetic order. If you are not happy with any item, we can arrange collection from you for a full refund (even if you are outside the UK) We will not provide any partial refunds and will not cover any restoration, detailed or internal cleaning, repairs or modification costs. Any questions regarding out of eBay deals will be ignored Any items suspected missing in transit, must be reported to us within 10 days. Shipping We ship using a 24 hour courier. Please allow up to 3 days handling time as a lot of our items are large and take time to package well. Collections Collections from our unit in Bordon are available on Wednesdays and Fridays. Visit our storeHi-Fi Hangar Vintage hifi specialists Other PROJECTS, SPARES & REPAIRS HI-FI & AUDIO EQUIPMENT AMPLIFIERS DISK PLAYERS (CD/DVD/MD/SACD) TUNERS CASSETTE/TAPE DECKS SPEAKERS STUDIO EQUIPMENT TURNTABLES/RECORD PLAYERS CARTRIDGES TONEARMS MERCHANDISE T-SHIRTS ACCESSORIES Payment We take payment through the ebay managed payment system, Shipping We ship using a 24 hour courier. Please allow up to 3 days handling time as a lot of our items are large and take time to package well. _gsrx_vers_1652 (GS 9.7.4 (1652))

NAD Verstärker NAD C 316BEE V2 - B-Ware - Aussteller - Super Verstärker Gewährleistung bis 04.04.2027 NAD C 316BEE V2Klirrfaktor (20 Hz – 20 kHz) <0,03 % an 300 Ohm bei 2 V Ausgangssignal Geräuschspannungsabstand >100 dB (A-gewichtet, 32 Ohm, 2 V Ausgangssignal, Verstärkungsfaktor Eins) Frequenzgang ±0,3 dB (20 Hz – 20 kHz) Ausgangsimpedanz 8 Ohm Dauerausgangsleistung an 8 und 4 Ohm 2 x 40 W (20 Hz-20 kHz bei angegebenem Klirrfaktor, beide Kanäle angesteuert) Klirrfaktor (20 Hz – 20 kHz) <0.03 % (250 mW bis 40 W, 8 und 4 Ohm) Geräuschspannungsabstand >95 dB (A-gewichtet, 500 mV Eingang, 1 W Ausgang an 8 Ohm) >97 dB (A-gewichtet, 500 mV Eingang, Verstärkungsfaktor Eins an 32 Ohm) Clipping-Leistung (bei 1 kHz 0,1 % Klirrfaktor) >45 W an 8 Ohm >60 W an 4 Ohm Impulsleistung 2 x 90 W an 8 Ohm 2 x 120 W an 4 Ohm 2 x 170 W an 2 Ohm Dämpfungsfaktor >200 (8 Ohm, 1 kHz) Frequenzgang ±0,3 dB (20 Hz – 20 kHz, Klangregelung abgeschaltet) Höhen: ± 5 dB bei 10 kHz Bässe: ± 8 dB bei 100 Hz Kanaltrennung >70 dB (1 kHz) Maximaler Eingangspegel 4,3 V (1 kHz, Klirrfaktor 0,1 %) Eingangsempfindlichkeit (für 40 W an 8 Ohm) 200 mV Standby-Stromverbrauch <0,5 W Klirrfaktor (20 Hz – 20 kHz) <0,03 % (1 W an 40 W, 8 und 4 Ohm) Geräuschspannungsabstand >75 dB mit IHF MM Abtaster (A-gewichtet, 5 mV Eingang 1 kHz und 1 W Ausgang an 8 Ohm) Frequenzgang (RIAA Entzerrung) +0,3 dB (20 Hz – 20 kHz, Klangregelung abgeschaltet) Maximaler Eingangspegel 71 mV (1 kHz, Klirrfaktor 0,1 %) Eingangsempfindlichkeit (für 40 W an 8 Ohm) 2,95 mV Abmessungen (B x H x T) 435 x 90 x 285 mm Gewicht 5,5 kg

ACHTUNG VERSAND NUR AUF EIGENE GEFAHR UND BEI VOLLER KOSTEN ÜBERNAHME.AUSLANDS VERSAND MÖGLICH . BITTE VERSANDKOSTEN VOR GEBOT NACHFRAGEN Sehr gute Heim Anlage der Spitzenklasse. Hochwertige High-end Stereoanlage von NAD NAD Vollverstärker 319 Modell: 319 ( In Fachwerkstatt Klangregler ersetzt und auf Funktion Geprüft ) Typ: Vollverstärker Baujahre: 1997 - 1999 Farbe: Schwarz Neupreis ca.: 1800 DM NAD 5 Fach CD Spieler 513 Modell: 523 Typ: Karussell-CD-Wechsler Baujahre: 1996 - 2001 Hergestellt in: Japan Farbe: Schwarz Neupreis ca.: 850 DM NAD Tape deck 618 Modell: 616 Typ: Doppel-Kassetten Tape Deck Baujahre: 1995 - 2001 Hergestellt in: Japan Farbe: Schwarz Neupreis ca.: 898 DM NAD RDS Tuner 414 Modell: 414 Typ: Tuner Baujahre: 1996 - 1998 Farbe: Schwarz Abmessungen (BxHxT): 435 x 96 x 319 mm Gewicht: 3,5 kg Neupreis ca.: 400 DM Technische Daten UKW/MW Empfang MOSFET Eingangsstufe Trennschärfe: 60 dB ZF-Unterdrückung: 90 dB Signal/Rauschabstand: >76 dB(Mono), >66dB (Stereo) 30 Stationsspeicherplätze automatischer Sendersuchlauf RDS Keine Fernbedienung mehr vorhanden. Aber Steuerung über Multi-pilot möglich. Anlage ist angeschlossen und kann Probe gehört werden. Test mit Lautsprecher Focal Chorus V möglich die können dann noch dazu erworben werden. „Ich schließe jegliche Sach­mangelhaftung aus.“ „Die Haftung auf Schaden­ersatz wegen Verletzungen von Gesundheit, Körper oder Leben und grob fahr­lässiger und/oder vorsätzlicher Verletzungen meiner Pflichten als Verkäufer bleibt uneinge­schränkt.“

Unit has been recapped. All caps replaced with high quality caps. Brown glue removed. Boards reflowed approx. 75%. Cleaned and inspected. Unit bias and DC offset set to factory specs. All controls cleaned. Unit tested and sounding great. Face and case has some minor wear and tear. The bal. works. Tested with scope. It is a little loose and it grabs to the left. Would have liked to replace but can not find one. 10 hours of work it and the buyer will enjoy for a long time to come.

You are bidding on 1 NAD 316BEE v2 amplifier (OPEN BOX) Ive kept this amp in the box for several months. I havent used it because of its lack of a sub out, and tower speakers arent an option for me at this point, so Im letting it go. Its just as powerful as advertised. It was purchased from an authorized retailers outlet store. In full disclosure, the left speaker terminals on the back are a bit loose (the amp arrived that way). Im assuming its an easy fix. The amp will ship in the original box with the manual and remote. Overview of the Specs: 40 watts x 2 channels into 4 or 8 ohms (20-20,000 Hz) at 0.03% THD (dynamic power 90 watts)signal-to-noise ratio: 95 dBPowerDrive-S™ technology for more dynamic power outputlarge toroidal power transformer for a strong, low-noise power supplyrotary bass and treble controls with defeat switch for tone control bypass5 RCA audio inputs including 1 MM phono inputfront-panel minijack input for connecting a portable music playerHeadphone jackSpeaker binding post terminals (one set of 4)remote controldimensions: 17-1/8W x 3-1/4H x 11-5/16Dweight: 12.1 lbs. The amp will ship via USPS. To the winning bidder, enjoy!

You are bidding on 1 NAD 316BEE v2 amplifier (OPEN BOX) Ive kept this amp in the box for several months. I havent used it because of its lack of a sub out, and tower speakers arent an option for me at this point, so Im letting it go. Its just as powerful as advertised. It was purchased from an authorized retailers outlet store. In full disclosure, the left speaker terminals on the back are a bit loose (the amp arrived that way). Im assuming its an easy fix. The amp will ship in the original box with the manual and remote. Overview of the Specs: 40 watts x 2 channels into 4 or 8 ohms (20-20,000 Hz) at 0.03% THD (dynamic power 90 watts)signal-to-noise ratio: 95 dBPowerDrive-S™ technology for more dynamic power outputlarge toroidal power transformer for a strong, low-noise power supplyrotary bass and treble controls with defeat switch for tone control bypass5 RCA audio inputs including 1 MM phono inputfront-panel minijack input for connecting a portable music playerHeadphone jackSpeaker binding post terminals (one set of 4)remote controldimensions: 17-1/8W x 3-1/4H x 11-5/16Dweight: 12.1 lbs. The amp will ship via USPS. To the winning bidder, enjoy!

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good

This is a service only listing for any parts I already have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit suitable for use with Intelligent Power Strips, etc. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. or WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. Realign Power Amps for 0mV Offset and specified Bias. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

Zum Shop NAD 3140 NostalgieDEFEKT für Bastler Lagerfund Wir räumen unser Lager gerade auf. Hier kommt ein defektes Schätzchen für Bastler und Sammler. Der Verstärker geht nicht an, daher als Ersatzteilspendernur nutzbar. Allgemein Hersteller: NAD Modell: 3140 Typ: Vollverstärker Hergestellt in: Japan Farbe: schwarz !!! Keine Garantie keine Rücknahme !!! Schaut auch auf unsere anderen Auktionen ... Schnapper sind garantiert !!! Bei Fragen oder Wünschen können sie uns gerne anrufen Tel: 0511/441046 Viele Grüße Vom Art&Voice Team aus Hannover

This is a service only listing for any parts I already have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Replace Power Switch and Upgrade Muting circuit. Experience has shown that the power switch is almost always worn out. The exact replacement now costs $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch and upgrade the muting to be all electronic, just like the 3225PE and 701. This makes the unit suitable for use with Intelligent Power Strips, etc. Note that I have raised the price $24 to include this service instead of asking for an additional $35 after the fact. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. or WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. Realign Power Amps for 0mV Offset and specified Bias. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.