This is a service only listing for any parts I have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace the Electrolytic Capacitors in the Power Supplies, Amplifier sections, and Tuner Audio sections. Ill upgrade the audio caps with nichicon, ELNA, Rubycon, and Panasonic audio grades while preferring 105C and/or higher voltage rated caps for the power supplies. I can also install any capacitors that you provide as desired. Note that replacing the power switch is an additional $35. If you hear a sizzling sound as you slowly push it on or off, then its time to replace it. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or Otherwise) that youd like to Buy and have repaired and/or recapped, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good

UNIT IS IN USED CONDITION. TESTED & WORKING. EXCELLENT HIGH QUALITY AMP. AMAZING SOUND. BUILT IN PHONO STAGE. GOOD WORKING ORDER. COSMETICALLY SOME RUBS / SIGNS OF USE. A SMALL PORTION OF THE TOP OF THE CASE IS A LITTLE SUNKEN DOWN DUE TO ANOTHER UNIT PREVIOUS STORED ON TOP. PURELY AESTHETIC AND DOES NOT AFFECT THE UNITS FUNCTIONALITY. CONSULT PHOTOS IN DETAIL FOR EXACT ITEM YOU WILL RECEIVE. TESTED & WORKING. USED CONDITION SpecificationsPower output: 35 watts per channel into 8? (stereo)Frequency response: 20Hz to 20kHzTotal harmonic distortion: 0.03%Damping factor: 100Input sensitivity: 2.5mV (MM), 170mV (line)Signal to noise ratio: 76dB (MM), 103.5dB (line)Dimensions: 435 x 110 x 310mmWeight: 6.9kgYear: 1996

Condition Unit has been Tested and Working Unit shows some signs of use, wear and scuffs. Additional Detail Power Cord Included No Power Adapter Included No other accessory included (We ONLY include what is in the pictures). Please contact us via the eBay message system if you have any questions. _____________________________________________________________________________________________________ Thank you for shopping with SF Goodwill! Your generous purchase from Goodwill makes a big difference for local people struggling with unemployment. Your purchase funds job programs and services for people overcoming challenges like homelessness, former incarceration, lack of job skills and limited education. We create second chances through training and the dignity of work. Payment: ??????Payments are due within 7 days from auction end date. Shipping: ??????We do not ship to PO Boxes or Military Addresses (ie: APO/FPO/DPO/etc) Combined Shipping: Yes, We Offer Combined Shipping Discounts! Item with the highest shipping price will be billed at full price shipping, additional items: 75% off each shipping cost Most orders qualify for an automatic combined shipping discount, simply check out and pay! Some items cannot be combined in shipping (fragile, oversize or heavy items) We cannot apply a combined shipping discount after payment has been made Please send us a direct message if you need help, or require a custom combined shipping invoice. Local Pickup: Were offering local pickup effective 11/1/2023. Once the auction has ended, choose the local pickup option during checkout. If you have any issues choosing local pickup, please let us know. Once checkout via local pickup has been completed, please allow 24-48 hours to contact you and schedule your order pickup. Local Pickup is by appointment only. We will not accept on the spot pickups. Orders must be picked up within 7-days of the scheduled appointment. Pickup extensions will not be offered. Contact us for the local pickup instructions. Order Issues and Questions: Problems with your order? Were here to help! Please contact us via the eBay message system if you have any issues with your order. Due to our high volume of sales, please allow 24-48 hours for us to respond to your messages. ______________________________________________________________________________________________________ Our Mission: Each year, nonprofit Goodwill of San Francisco, San Mateo and Marin breaks the cycle of poverty for thousands of local people through our transformative free training and work placement programs. Goodwill serves anyone who comes through our doors with a willingness to work. Job Creation: From skills training to job coaching that leads to employment, we identify and develop job-readiness skills on both a personal and professional level, plus offer a variety of employment support services. Employment at Goodwill: Our 21 retail stores, 25 attended donation centers and 2 warehouses employ more than 600 people and provide training and employment opportunities for individuals seeking to learn and build work skills that lead to career pathways. Employment with Top Bay Area Companies: Our experienced employment coaches connect work-ready job seekers with open positions at a range of companies throughout San Francisco, San Mateo and Marin counties. Impacts: Last year, Goodwill of San Francisco, San Mateo and Marin placed our participants in 636 jobs and transitional employment opportunities. In addition, education, job training, and employment services were provided to 3,200 people in our three-county region, and 10,300 visits were made to our Comprehensive Access Point Job Center.

Nad 8020e tweeter Tested working Will be re-tested prior to shipping. Good cosmetic condition. There are two breaks in the plastic trim where the screw holes are. Please see photos. Everything in the photos is included. If its not photographed, its not included Myref#.S10 -pnk479

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good

This is a diagnostic only listing for an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models.

NAD Model 3120 Integrated Amp MM/MC (Classic Audiophile) Superb Orig. Box/Manual. Recently checked by tech. in Good workig condition! Check ebay right now to see how many other 3120s are for aution right now. As you have become aware the less auctions for a certain models becomes apparent. This was the last iteration of 3020B. A giant killer was used in many older reviews. This unit has a small discoloration on the top back left corner. Iwill be moving in the near future and wont be taking much of my big collection with me. Please take a good look at the pics as youare getting what you see. thanks for looking/bidding, see my other auctions. ebayer since 1999. thanks

This is a service only listing for any parts I have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace the Electrolytic Capacitors in the Power Supplies, Amplifier sections, and Tuner Audio sections. Ill upgrade the audio caps with nichicon, ELNA, Rubycon, and Panasonic audio grades while preferring 105C and/or higher voltage rated caps for the power supplies. I can also install any capacitors that you provide as desired. Note that replacing the power switch is an additional $35. If you hear a sizzling sound as you slowly push it on or off, then its time to replace it. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or Otherwise) that youd like to Buy and have repaired and/or recapped, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

UNIT IS IN USED CONDITION. TESTED & WORKING. EXCELLENT HIGH QUALITY AMP. AMAZING SOUND. BUILT IN PHONO STAGE. GOOD WORKING ORDER. COSMETICALLY SOME RUBS / SIGNS OF USE. A SMALL PORTION OF THE TOP OF THE CASE IS A LITTLE SUNKEN DOWN DUE TO ANOTHER UNIT PREVIOUS STORED ON TOP. PURELY AESTHETIC AND DOES NOT AFFECT THE UNITS FUNCTIONALITY. CONSULT PHOTOS IN DETAIL FOR EXACT ITEM YOU WILL RECEIVE. TESTED & WORKING. USED CONDITION SpecificationsPower output: 35 watts per channel into 8? (stereo)Frequency response: 20Hz to 20kHzTotal harmonic distortion: 0.03%Damping factor: 100Input sensitivity: 2.5mV (MM), 170mV (line)Signal to noise ratio: 76dB (MM), 103.5dB (line)Dimensions: 435 x 110 x 310mmWeight: 6.9kgYear: 1996

NAD Electronics Instruction Manual for NAD 3130 Integrated Amplifier - installation & operation. In very good condition. No tears. A few minor pale spots on front corner as seen in photo. Printed 1986

This is a service only listing to Restore and Re Cap one NAD 3140 amplifier that YOU send to me. The shipping charge is for the return trip back to you in the same box sent. Installation of four Banana Jack/Binding Posts for SPEAKER_A are included.

This NAD 3140 has been upgraded and custom retrofitted to eliminate the thermal issues that plagued this model throughout its production. There are overheating 2-watt resistors in the preamp power supply that bake (and prematurely deteriorate) the surrounding purple electrolytic caps to a golden brown. I have relocated these resistors on terminal strips above and away from the other components. See the last photo. A second set of overheating resistors that supply the front panel LEDs (of all things!) has been eliminated by upgrading the ancient LEDs with much lower power versions. The soft clipping circuit has been updated to the latest Zener diode version (per the Service Bulletin) but with four 1 watt zeners instead of two 1/2 watt zeners to reduce the overheating that was occurring in that area as well. I have installed four Banana Jack/Binding Posts for SPEAKER_A in addition to the original Spring Terminals. The standard 3/4 spacing accommodates paired plugs. I have replaced ALL of the electrolytic capacitors. The four 4700uF Main Caps have been upgraded from 50V to 63V since they are actually charging up to 51V in this unit (NAD was notorious for this). The other power supply caps have been upgraded to higher voltage and/or 105C temp ratings. The audio caps have been upgraded to ELNA, nichicon MUSE BP, FW, and Fine Gold Audio as well as Vishay Film in the Bass_EQ and Control amps. I also replaced many of the 0.1 disc caps that were looking old and baked and worn with new multi-layer ceramics. I have upgraded the 4 very sensitive Bias and Offset adjustments to multi-turn trimpots. They allow a more precise adjustment that is less likely to drift or be accidentally disturbed. I have cleaned the switches with Deoxit D5 and cleaned/lubed the pots with Deoxit Fader F5. Cosmetically, this unit is in good condition. It has a few scrapes on the top cover and the front panel. Please see photos. Full refund within 60 days. Buyer pays return shipping. Please message me with any questions, corrections, etc. ******* Chapter TWO ******* It seems clear to me that the design goal of the NAD 3140 was to be twice as good as the iconic 3020. It is rated at twice the RMS power (40 WPC), has two phono inputs, two source selection switches (listen and record), two Bass_EQ contours, two tape loops, two sets of speaker outputs, two led power meters, and even two power transformers that are wired in series to behave as one massive chunk of iron. All that combined with over twice the Main Capacitance provides a Dynamic Power IHF rating of 80 WPC at 8 ohms, 130 WPC at 4 ohms, and 160 WPC at 2 ohms. The 3140 is an all-discrete design. The sophisticated 7-transistor MM/MC Phono Preamp has both Phono_1 and Phono_2 input jacks DC coupled to an FET gate with no coupling capacitor. A very unique feature of the 3140 is its 5-transistor 12db BASS_EQ Amplifier stage that can be selected to extend the low frequency response of almost any speaker by an octave centered around 45 Hz (Tower Speakers) or 70 Hz (Bookshelf Speakers). While the additional demands on the power amplifier can be significant, this amp can deliver. Another unique feature is the S.L.C. or Speaker Lead Compensation feedback in the Power Amplifier. It is meant to compensate for long and/or light gauge speaker wire, but I find it pleasing under all conditions, and usually leave it on. NOTE: Unlike most power amplifiers, the 3140 connects to all Speakers as if in a bridged configuration. The Negative Speaker terminals are NOT common ground. They are actually the S.L.C. feedback for each channel.

NAD Electronics Instruction Manual for NAD 3130 Integrated Amplifier - installation & operation. In very good condition. No tears. A few minor pale spots on front corner as seen in photo. Printed 1986

This is a service only listing for any parts I have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace the Electrolytic Capacitors in the Power Supplies, Amplifier sections, and Tuner Audio sections. Ill upgrade the audio caps with nichicon, ELNA, Rubycon, and Panasonic audio grades while preferring 105C and/or higher voltage rated caps for the power supplies. I can also install any capacitors that you provide as desired. Note that replacing the power switch is an additional $35. If you hear a sizzling sound as you slowly push it on or off, then its time to replace it. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or Otherwise) that youd like to Buy and have repaired and/or recapped, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

NAD 451 GENUINE REMOTE CONTROL FOR C317 C320 C350 C370 C740, Perfect Working.

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good

EINGESTELLT MIT

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good

Thorens TD125 Original Wooden Plinth New & Unused Owned From New & Never Used Super Rare Looks Great Will Come With The Original Box Please Look At The Photos For Condition The Plinth Will Be Very Well Packed And You Will Receive It Exactly As Seen In The Photos International Buyers Please Contact Us For An Accurate Shipping Quote

NAD 314 Stereo Integrated Amplifier 35 Watts Per Channel. Near perfect condition. Ive had this for nearly 30 years and most of the time its been used as a pre-amp for the phono stage. The power output has hardly been used. Its all in perfect working order. Only selling because of a recent upgrade. May collect if you want to Any questions please ask Thanks for looking

Who knew what power and sophistication lurked within the modest confines of the NAD 3125! It is clearly a Proton in disguise, with the telltale Power Transformer (last photo) and overall elegance of design. Schematically, the 3125 contains a Souped Up version of the original 3020 Power Amp design with Higher Voltage Main Rails and TWICE the Main Capacitance of the original 3020, 3020x and 3220PE spinoffs, as well as its own 7125 Receiver. Who knew? My favorite feature is the Bass EQ contour that extends the low end of almost any speaker by taking advantage of this High Power/Current capability. This is the second 3125 Ive serviced, both of which had many original ELNA Electrolytic caps that tested really bad, as in open or as a high value resistor. I have upgraded the Power Supply caps to nichicon, Panasonic, TDK and Chemicon. The 4 Main Caps are NIC. A single transistor Line Input Buffer and low noise OP-AMP design allows for unusually low value audio coupling and filter capacitors. As such, I have upgraded 3 pairs of Electrolytic audio coupling caps with Metal Film for non-polar operation and better performance. The other audio coupling pairs have been upgraded to Philips, ELNA BP, and nichicon MUSE BP. I have also upgraded the Power Amp Bias and Offset adjustments to multi-turn trimmers which are more precise and less likely to drift. I have re-soldered the rear RCA jacks, the front switches, controls, and headphone jack, and much of the main board itself. I then cleaned the solder side with Flux Remover and Alcohol. It looks better than new. The input select switches were showing signs of physical aging and deterioration, so I reinforced them with cable ties and several coats of craft glue. They are now as strong as ever. The original AC power plug has also been replaced, as the old one just looked shabby. Cosmetically, this unit is is very good condition with surface scratches here and there. Please see photos. The top cover and front panel are a single metal piece. The funky plastic side panels could easily be replaced by nice, stained wood panels, etc. Full refund within 60 days. Buyer pays return shipping. Please message me with any questions, corrections, etc.

NAD 3140 speaker connectors 12-2095 NAD part #: 12-2095 good