1 Pair of Emotiva XPA HC1 Class A/B Mono Block Amplifiers 300 Watts @ 8 Ohms. I purchased these last March and are still under the manufacturers warranty (5Yrs total) selling due to upgrading to a pair of much more expensive tube amplifiers. Comes with original boxes and all paperwork. Specs: https://emotiva.com/products/hc-1

Emotiva XPA-100 Mono amp- Audiophile mono block (one channel) amplifier; 400 watts at 4 Ohms; 250 watts at 8 Ohms- Fully discrete signal path, with class A/B output stage and massive power reserves- Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring I bought this about 8 years to power my center channel, I am down sizing and no longer need it. Comes with the owners manual and power cord.

Circuit TopologyA fully modular, fully differential, fully balanced audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection.NOTE: This is a fully balanced amplifier with a floating, differential output stage. The output terminals must NEVER be tied together or ground referenced. Doing so will cause immediate damage that is NOT covered under warranty. If you have any questions about speaker compatibility, please contact Emotiva for technical support.Audio SpecificationsThe XPA-DR1 features one Differential Reference™ Amplifier Module. Audio Specifications (One Differential Reference Amplifier Module):Power Output: 650 watts RMS into 8 Ohms at <0.1% THD. 1000 watts RMS into 4 Ohms at <0.1% THD.Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB).Broad Band Frequency Response: 20 Hz to 50 kHz +0/-2 dB.THD + noise: < 0.015%; at 100 watts RMS; 1 kHz; 8 Ohms.Signal to Noise Ratio (8 Ohm load): > 122 dB; ref FTC rated power; unbalanced input (A-weighted). > 96 dB; ref 1 watt; unbalanced input (A-weighted).Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads).Damping Factor (8 Ohm load): > 500.Input Sensitivity (for rated power; 8 Ohm load): 2.4 V.Gain: 29 dB.Maximum Power Consumption: 1,000 watts. Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore they are not at all characteristic of what you would expect when playing music or the sound track from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered to be a circuit requirement for normal operation.Input Impedance: 33 kOhms (balanced). 23.5 kOhms (unbalanced).Input And Output ConnectionsInput Connections: Unbalanced (RCA); balanced (XLR); one each, user selectable.Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.Trigger: Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA.Power RequirementsBetween 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).Front Panel Controls and IndicatorsStandby: push button (halo ring changes color to indicate Standby or On).Status LEDs: one per channel; blue. Status LEDs change to red to indicate a fault condition.Rear Panel ControlsAC Power switch: rocker switch (switches AC main power).Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs.Circuit Breaker: press button to reset circuit breaker.ProtectionThe XPA-DR1 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.MechanicalDimensions: 17” wide x 8” high x 19” deep (unboxed; including feet). 17” wide x 7” high x 19” deep (unboxed; without feet). 24-1/2” wide x 12” high x 24-3/4” deep (boxed).Weight: 35.5 lbs (unboxed). 40.5 lbs (boxed).

Up for sale is my pristine Emotiva DR-1 pair of true monoblock power Amps. Comes with everything to include OEM box so you know it will ship safe and sound Here is the specs: The XPA-DR1 is a true monoblock power amplifier, and features a single Differential Reference Amplifier Module, in a true monoblock configuration, powered by its own dedicated 3 kW switch mode power supply. The XPA-DR1 provides massive power, superb dynamics, incredible resolution, and absolute control. If you’re looking for the very best sound quality, with virtually endless reserves of power against a jet black noise floor, this is the amplifier for you. The XPA-DR1 delivers 650 watts RMS into 8 Ohms, and 1000 watts RMS (that’s 1 kW) into 4 Ohms, with less than 0.1% THD. The Power Supply: The Foundation Of A Great Amplifier In amplifier design, everything starts with the power supply. The XPA-DR1 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions.

this is the big one, differentiail reference unit, super heavy, i will double box it, but as with my other auctions I will insure it for the purchase price, I will not be responsible if the shipper damages the package, its been alot lately, and not at the fault of BHB, we over pack if anything.

this is the big one, differentiail reference unit, super heavy, i will double box it, but as with my other auctions I will insure it for the purchase price, I will not be responsible if the shipper damages the package, its been alot lately, and not at the fault of BHB, we over pack if anything.

Emotiva XPA1 Gen 2 Monoblock Amplifier Pair XLNT Hard To Find! Easily the most desirable of Emotiva’s high power amplifier line since they began producing them and NO LONGER available as Emotiva has switched to class D designs. The Gen 2 model builds on the original XPA-1 Monoblocks with a massive 600w power rating at 8ohm and 1000w at 4. There is likely no speaker that these monsters can not handle with aplomb. Have been previously handling a pair of Revel Studio 2 listed separately. Additionally, the Gen 2 model Can be run in straight class A mode via a front panel switch. This particular pair is in excellent overall cosmetic condition with some minor nicks and very light scratches in a few spots. NEVER in a smoking household and never abused, these have been lovingly cared for and sound sonically excellent as well. Ready to take your audio system home theater setup to the next level. Includes original boxes, packing and power cables. Due to weight these are LOCAL PICKUP ONLY.

My girlfriend is moving in with me and I have to downsize my hifi gear.Therefore, Im selling my beloved pair of Emotiva XPA-1 One 2 power amplifiers. They are in mint condition without any scratches and I have the original packaging. This is a pair of very powerful amplifiers that can be driven in pure class A or in A/B. https://hometheaterhifi.com/reviews/amplifier/power-amplifier/emotiva-xpa-1-gen-2-monoblock-power-amplifier-review/ The price is for a pair and I can bring it to Germany close to the Swiss border for EU buyers but due to the weight I cant offer shipping.

The power amplifier performs the simple but critical job of boosting the output signals from each channel of your stereo preamp or surround sound processor to the level necessary to drive your loudspeakers. While this may seem trivial, a really good power amp is essential to having a great audio system, because any flaws in the performance of your power amp are going to limit the performance of your entire system. Every amplifier in the new Third Generation XPA series was carefully designed to deliver superb technical performance, unsurpassed sound quality, and an exceptionally accurate and dynamic rendition of all types of music, thus ensuring that your entire system will sound its absolute best. Each individual XPA amplifier is modular, and can be customized to provide exactly the power and number of channels you need today, and expanded later if your needs change; and multiple matching chassis enable you to add even more channels, or more power, for a near endless variety of options. The new XPA-11 is an eleven-channel audiophile quality power amplifier. The XPA-11 is populated with three of our High-Powered Single Channel Modules, and four of our Stereo Modules, for a total of three high-powered channels and eight lower-powered channels. This combination is ideal for a surround sound system that is used for both music and home theater listening, and includes height speakers. The three front speakers, which are the most critical for both music and home theater listening, are powered by the three high-powered channels. The surround channels, and the height channels, are driven by the lower powered stereo modules. Even though the channels differ in terms of maximum power output, they feature perfectly matched electrical characteristics, and the same superb Class A/B sound quality. The XPA-11 is perfect for powering:A 7.1.4 or 5.1.6 Dolby Atmos or DTS-X systemA 7.1 or 7.2 channel system that also includes two pairs of smaller speakers in other zonesConfiguration: 3 x High-Powered Single-Channel Modules4 x Stereo ModulesThe power output capabilities of the various channels on the XPA-11 were optimized to provide the best sound quality in real-world listening conditions; the front channels, which are the most critical for both dynamic music reproduction and crystal clear dialog, receive the most power. (This is especially the case if your system features large tower speakers in the front, a large center channel speaker, bookshelf or wall mounted surrounds, and ceiling mounted height speakers.) Power output (High-Powered Single Channel Modules):300 watts/channel RMS into 8 Ohms; two channels driven490 watts/channel RMS into 4 Ohms; two channels drivenPower output (Stereo Modules): 65 watts/channel RMS into 8 Ohms; two channels driven 100 watts/channel RMS into 4 Ohms; two channels drivenWhy You Need A Dedicated Power AmplifierMost experts agree that, if you want the absolute best sound quality and technical performance, separate components are the way to go. Our new Third Generation XPA series power amplifiers are all designed from the ground up to perform a single critical task – to accurately reproduce every detail and nuance of your music. By focusing all of our efforts on that one goal, we’ve been able to design an amplifier that performs its job with remarkable precision, and avoids most of the compromises that limit lesser designs. Experience Meets Cutting Edge TechnologyWhen we set out to design the latest version of our XPA series of amplifiers, we analyzed everything in every amplifier we’ve ever made, from front to back, inside and out. By combining years of design experience, with a thorough understanding of recent advances in audio technology, we were able to determine several areas where we could improve on our previous designs. After carefully weighing all the options, we kept the best features of our previous models, added some new technology where we determined it would actually deliver significant improvements, and optimized several operating parameters to ensure that it would all work together flawlessly. The new Third Generation represents a significant improvement for our highly acclaimed XPA series of amplifiers – and delivers improvements in both technical performance and sound quality.All of the models in our new Third Generation XPA amplifier family are designed to reproduce today’s high definition movie sound tracks and music sources with awesome realism, amazing finesse and precision, and without the slightest hint of strain or signal compression. They deliver a listening experience that is far above anything you can achieve with multi-purpose components like receivers, or with other amplifiers in their modest price range. We’re talking about real-world power and fidelity that you can immediately hear and appreciate. Designed and Assembled in the USA with Globally Sourced ComponentsAll of our new Third Generation XPA power amplifiers, including the XPA-11, are designed, assembled, and tested in the USA. Assembling products here in the USA gives us exceptional control over every facet of the design and production process, which helps us build the highest quality products for our customers while minimizing unnecessary complications and production delays. Each Emotiva amplifier is carefully designed with premium components to deliver a stunningly capable, reliable, and refined system. Note: To ensure that amplifier channels are always installed properly, and function to our specifications, amplifier modules must be installed by Emotiva, or by your local authorized Emotiva service representative.FEATURED SPECIFICATIONSAudioPower output (High-Powered Single Channel Modules): 300 watts/channel RMS into 8 Ohms; two channels driven | 490 watts/channel RMS into 4 Ohms; two channels drivenPower output (Stereo Modules): 65 watts/channel RMS into 8 Ohms; two channels driven | 100 watts/channel RMS into 4 Ohms; two channels drivenAudiophile quality Class A/B output stage.Balanced and unbalanced inputs for compatibility with a wide variety of preamps and surround sound processors.Design TopologyClass A/B output stage; Optimized Class H power supply topology on High-Powered Single Channel Modules for improved efficiency.Regulated switch mode power supply combines massive power capability, high reliability, excellent performance, and reduced weight.FeaturesFully modular construction for optimum flexibility.Universal AC power automatically selects the proper line voltage for easy installation in a wide variety of locations.Comprehensive yet transparent protection circuitry protects from most common fault conditions without degrading sound quality. HardwareDimensions: 17” x 19” x 8” (including feet) Weight: 53 pounds (unboxed) Power Requirements: 100 – 250 VAC 50/60 Hz (automatically detected).

Emotiva Audio XPA-100 Gen 2 - Mono Block Power Amplifier, 400 Watts at 4 Ohm. XLR / RCA Input Single Owner, no issues with this amp, rock solid, quiet, no fans, runs cool even at full loads. Audiophile mono block (one channel) amplifier; 400 watts at 4 Ohms; 250 watts at 8 Ohms Fully discrete signal path, with class A/B output stage and massive power reserves Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring. I dont have the 4 feet for this unit, but they are not needed unless you are stacking amps. Generic feet can added easily.This amp has the Grey front panels, not the standard black ones on the Gen-2, but this is a Gen-2 Model.

Emotiva XPA HC-1 High Current Monoblock Amplifier. Mint condition. Local pickup only, no shipping.

This listing is for a used Emotiva XPA-5 Generation 1, five-channel audio amplifier. It includes the amplifier, power cable, and original packaging. It is in good working order, from a no pet/no-smoking home and well taken care of. There are light blemishes associated with normal use, but the unit works well and has been our primary home theater amplifier for years, only to be replaced with a recent upgrade. Here are the specifications: Specifications: - 5 – independent mono blocks @ 200 wpc into 8 ohms; 350 wpc into 4 ohms - Class A/B design with short signal path - Triple Darlington with Toshiba output stages - Dual Differential input Balanced (XLR) and Un-balanced (RCA) - Audiophile quality 5 way binding post - THD+N at rated power output: 0.007% - S/N ratio: >100db 10 to 120Khz (-3db) and 20 to 20 (with less than .15db deviation) 32db gain structure - 1600VA toroidal transformer - 60,000uF secondary capacitance - 70 pounds - 17” W x 8” H x 19” D Listed on multiple sites. Local pickup only. Thank you for looking, and feel free to ask any questions.

Emotiva Audio XPA-100 Gen 2 - Mono Block Power Amplifier, 400 Watts at 4 Ohm. XLR / RCA Input Single Owner, no issues with this amp, rock solid, quiet, no fans, runs cool even at full loads. Audiophile mono block (one channel) amplifier; 400 watts at 4 Ohms; 250 watts at 8 Ohms Fully discrete signal path, with class A/B output stage and massive power reserves Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring. I dont have the 4 feet for this unit, but they are not needed unless you are stacking amps. Generic feet can added easily.This amp has the Grey front panels, not the standard black ones on the Gen-2, but this is a Gen-2 Model.

Emotiva Audio XPA-200 2 Channel Power Amplifier, 150 watts into an 8 ohm load and 240 watts into a 4 ohm load (both at <1% THD) Single Owner, no issues with this amp, rock solid, quiet, no fans, runs cool even at full loads. Fully discrete signal path, with class A/B output stage and massive power reserves Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring. Also Selling the Mono XPA-100 amp to match.

Emotiva Audio XPA-200 2 Channel Power Amplifier, 150 watts into an 8 ohm load and 240 watts into a 4 ohm load (both at <1% THD) Single Owner, no issues with this amp, rock solid, quiet, no fans, runs cool even at full loads. Fully discrete signal path, with class A/B output stage and massive power reserves Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring. Also Selling the Mono XPA-100 amp to match.

Up for sale is a pair of the legendary Emotiva XPA-1L monoblock power amplifiers. These amplifiers are famous for user selectable bias level. The amplifier is rated 250 W of class A/B power into 8 ohms / 500 W into 4 ohms. The user can opt for the first 35 watts to be delivered in class A operation via a front panel switch. Class A amplifiers are highly prized for their lack of cross-over distortion. Normally class A capable amplifiers are very expensive. The Emotiva XPA-1L was very affordable at $699 each when released. General specifications:Frequency response: 10 Hz - 80 kHzTHD: 0.005%Damping factor: 500Gain: 29 dBSignal-to-noise ratio: 116 dBRCA and XLR inputs12 volt trigger input and output (allows daisy chaining the trigger signal)90,000 uF power supply capacitance450 VA transformerIEC power connection and cordDimensions: 17 W x 3.875” H x 19” deep (note this is a very deep amplifier, make sure it will fit into your audio rack)Weight: 35 poundsAmplifiers are in excellent condition (9/10) and ship with original power cords and factory double boxes. These were in my dedicated listening room for the last 5 years and have seen light use. I am the 2nd owner; the original owner purchased them Jan 2014.

Presenting a rare gem: the Emotiva XPA-1L Monoblock Power Amplifier Class A & A/B. This exceptional pair is in excellent condition and offers an extraordinary audio experience.You can access the monoblock manual at https://www.manualslib.com/manual/678573/Emotiva-Xpa-1l.html. Key Features:- Power Output: 35W Class A or 250W Class A/B per channel at 8 Ohms- Impressive Sound: Delivering a beautiful audio performance in details- Sturdy Build: Each unit weighs a substantial 45 lb (including the box) (shipping calculation here combines both units).

Listed here is one piece of a pair of Emotiva XPA-1L Monoblock Power Amplifier Class A & A/B with S/N 1335. The other piece (S/N 1582) is listed separately to follow some eBay requirement. You will want to purchase both pieces together to complete the pair. They both are in excellent conditions. The monoblock manual can be found https://www.manualslib.com/manual/678573/Emotiva-Xpa-1l.html You may also want to check out the separately listed Emotiva MC-700 7.1 Channel 4K HDR Surround Sound Processor.

Listed here is one piece of a pair of Emotiva XPA-1L Monoblock Power Amplifier Class A & A/B with S/N 1582. The other piece (S/N 1335) is listed separately to follow some eBay requirement. You will want to purchase both pieces together to complete the pair. They both are in excellent conditions. The monoblock manual can be found https://www.manualslib.com/manual/678573/Emotiva-Xpa-1l.html You may also want to check out the separately listed Emotiva MC-700 7.1 Channel 4K HDR Surround Sound Processor.

My girlfriend is moving in with me and I have to downsize my hifi gear.Therefore, Im selling my beloved pair of Emotiva XPA-1 One 2 power amplifiers. They are in mint condition without any scratches and I have the original packaging. This is a pair of very powerful amplifiers that can be driven in pure class A or in A/B. https://hometheaterhifi.com/reviews/amplifier/power-amplifier/emotiva-xpa-1-gen-2-monoblock-power-amplifier-review/ The price is for a pair and I can bring it to Germany close to the Swiss border for EU buyers but due to the weight I cant offer shipping.

Product Specifications: Emotiva XPA-3 Gen 1 Multi-Channel Power Amplifier Accessories: Not IncludedDescription: Unit has been tested to verify functionality. If not stated you will only receive what is seen in the photos.Appearance: Unit is in very good pre-owned/used condition with minor cosmetic damage. ---Please feel free to contact us if you have any additional questions about the product. If choosing Local Pickup: Local Pickup Policy All items must be picked up within 14 days of purchase.Any item not picked up within 14 days of purchase will be cancelled, refunded and relisted without notification.All items picked up must be picked up by the individual named in the profile.No 3rd party pickups without prior approval.Identification is required to be shown when picking up all ordersAll pick-up orders must be paid for prior to pick-up. Payments will not be accepted on-site - no exceptions.No Walk-Ins. If you have not scheduled and received a confirmation of your pick up time, we will not be able to accommodate your pick up.Local pickup must be scheduled prior to arrival by contacting Customer Service.The pickup address for all items is 1080 N. 7th Street, San Jose, CA 95112Local pickup is available by appointment only and must be picked up within 14 days.

For your consideration, a new open-box Emotiva XPA-100 Monoblock Power Amplifier. Perfect cosmetic and functional condition complete with original box, styrofoam inserts, manual, power cord, auxiliary cord and dust cover. Clean, complete, tested and working; laser film is still on the display. Original box is missing two dog flaps on the top or the box, but I’ll be overbox the original box when I ship it. Please see photos as what you see is exactly what you will receive. Please let me know if you have any questions. Thanks!

EMOTIVA XPA-100 Monoblock Power Amplifier in original box Signature Required upon delivery Very well taken care of. Upgraded to larger amp. Please note this amp powers one single speaker. Please see all pictures and research before making purchase. Please look at all pictures to make sure this is what you want, before making purchase.I Leave positive feedback when positive is left for me.Feel free to contact me with any questions you may have and I will do my best to help.I work days so please understand that it may take a few days to ship out.I do NOT offer local pick up. Thank you

My girlfriend is moving in with me and I have to downsize my hifi gear.Therefore, Im selling my beloved pair of Emotiva XPA-1 One 2 power amplifiers. They are in mint condition without any scratches and I have the original packaging. This is a pair of very powerful amplifiers that can be driven in pure class A or in A/B. https://hometheaterhifi.com/reviews/amplifier/power-amplifier/emotiva-xpa-1-gen-2-monoblock-power-amplifier-review/ The price is for a pair and I can bring it to Germany close to the Swiss border for EU buyers but due to the weight I cant offer shipping.