Excellent condition Emotiva XPA-1 Gen 1 Differential Monoblock Amplifier. Includes original box. Note, the RCA plug is slightly loose. It works fine, however has some static if you wiggle the RCA too much while connected. The XLR balanced connection works flawlessly so I never used the unbalanced RCA. Local pickup or will ship at buyers expense Specs below: 1 ChannelTopology: Fully Discrete, Dual Differential, High Current, Short Signal Path Class A/BPower Output: 1000 watts RMS @ 4 ohm (0.1% THD); 500 watts RMS @ 8 ohm (0.1% THD)Power Band Response: 20 Hz to 20 kHz with less than .05 db deviation at rated powerBroadband Frequency Response: (-3db): 5Hz to 150kHzAmplifier Gain: 32dbSignal to Noise Ratio: 1 watt: >89db Full Power: >117dbInput Impedance: Unbalanced – 20kohms Balanced – 18kohmsTransformer Size: 1200VASecondary Capacitance: 120,000uFOutput Devices: 24Size: 17” W x 7.75” H x 19.5” D (depth is measured from front faceplate to end of protective rear panel rubber pieces)

Unit in good condition Minor scratches Brand Emotiva Model XPA-1L One unit only No other accessories included Power cord not included Parts only When switch is turned on amp just makes clicking noise constantly until turned off. Will not power on Free shipping Fast 1 day handling time

Emotiva XPA-1L, with selectable ClassA and Class A/B operating modes. Now you can have both: remarkable sound backed by real power.In Class A/B Mode, the XPA-1L is a potent, superb sounding, fully balanced mono-block Class A/Bamplifier – delivering 250 watts into 8 ohms (or 500 watts into 4 ohms) with incredibly low levels ofnoise and distortion. Flip the switch into Class A Mode and the XPA-1L transforms into a pure Class A,high bias 35 watt sweetheart... with a kick. If you exceed the 35 watt threshold, it seamlessly transitionsinto Class A/B mode when the signal level goes above 35 watts, allowing it to deliver its full power. Youget the awesome purity of Class A for power levels up to 35 watts, with none of the power limitations.(The XPA-1L does run a bit warmer in Class A Mode, but, hey, it’s worth it.) SpecificationsTopology:Fully balanced, fully discrete, quad differential, high current, short signal path,with user switchable Class A or Class A/B operation.Number of Channels:1Power Output (rated power; THD < 0.1%):250 watts into 8 Ohms; Class A/B operation.500 watts into 4 Ohms; Class A/B operation.35 watts Class A, transitioning to 250 watts Class A/B into 8 ohms; Class A operation.Note: In Class A mode, the XPA-1L operates in pure Class A mode at all power levels up to 35watts, at which point it automatically transitions into Class A/B mode.Rated Power Bandwidth (at rated power; 8 Ohm load):20 Hz to 20 kHz + / - 0.15 dB.Minimum Recommended Load Impedance:4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads).Frequency Response:10 Hz to 80 kHz (+ 0 / - 2 dB).THD + noise:< 0.005%Signal to Noise Ratio (8 Ohm load):> 90 dB at 1 watt (A-weighted).> 116 dB at rated power (A-weighted).Damping Factor (8 Ohm load):> 500 Speaker Output Connections:Audiophile grade five-way binding posts, gold plated with clear insulator, 1 pair.Power Supply:90,000 uF of storage capacitance.450 VA heavy duty toroidal transformer.Input Sensitivity (for rated power; 8 Ohm load):1800 mV.Gain:29 dB.Input Connections:Unbalanced (RCA); balanced (XLR); switchable.Input Impedance:50k ohms.Trigger:Trigger Input: 5 - 20 V (AC or DC); <10 mA input current required.Trigger Output: 12 VDC; can drive any load up to 100 mA.Power Requirements:115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched).Front Panel Controls and Indicators:Standby; push button (halo ring changes color to indicate Standby or On).Status LED; illuminates blue for normal operation, flashes red during power-up or when a faultoccurs (may be disabled by rear panel Status LED switch).Rear Panel Controls:AC Power switch; rocker switch (switches AC mains power).Status LED switch; small slide switch (disables front panel Status LED).Input selector; toggle switch (selects between balanced and unbalanced inputs). Shipping to Switzerland is same price as Germany and from within CH.

Up for sale is my pristine Emotiva DR-1 pair of true monoblock power Amps. Comes with everything to include OEM box so you know it will ship safe and sound Here is the specs: The XPA-DR1 is a true monoblock power amplifier, and features a single Differential Reference Amplifier Module, in a true monoblock configuration, powered by its own dedicated 3 kW switch mode power supply. The XPA-DR1 provides massive power, superb dynamics, incredible resolution, and absolute control. If you’re looking for the very best sound quality, with virtually endless reserves of power against a jet black noise floor, this is the amplifier for you. The XPA-DR1 delivers 650 watts RMS into 8 Ohms, and 1000 watts RMS (that’s 1 kW) into 4 Ohms, with less than 0.1% THD. The Power Supply: The Foundation Of A Great Amplifier In amplifier design, everything starts with the power supply. The XPA-DR1 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions.

The Emotiva XPA-2. Gen 2 is a powerful and versatile power amplifier that offers high-quality audio output with its fully discrete, dual differential, high current, short signal path Class AB topology and single-ended L/R RCA and balanced XLR audio inputs. This unit, with its 300 watts of power per channel @ 8ohms in stereo, is ideal for any home audio or video setup, and its sleek black design is sure to fit in with any decor.With features like analog audio outputs and two channels for input and output, the Emotiva XPA-2. Gen 2 is a must-have for any serious audiophile. This unit, made by a trusted brand like Emotiva, is a beast of an amplifier for the money. This is high value power! It has a 15mm milled aluminum faceplate, a switch on the back to turn the 11 segment blue LED meter lights ON/OFF, audiophile gold plated 5-way binding posts, switchable stereo/mono operation, mains power switch on back, Standby On/Off on front center. This amplifier presents as new condition. Factory, heavy duty power cable, factory dust cover and original manual in excellent condition is included. Will ship in factory packaging which is a heavy duty cardboard outer shell which houses another heavy duty cardboard inner box which the amplifier actually resides in. The amplifier is encased in heavy duty molded foam with extra cardboard top and bottom plates. See pictures for visual desciption. One important note: I am the original owner, and I can say for certainty this item has been cared for during my ownership. You will see once you receive it and open it up. 300 watts per channel @ 8ohms in stereo500 watts per channel @ 4ohms in stereo1000 watts per channerl @ 8ohms in bridged mono modeDamping factor >50045,000 uF storage capacitance1200 VA heavy(!) duty toroidal transformer72.6lbs83.5lbs boxed

EMOTIVA XPA-200 Power Amplifier. 240 W per Channel. TESTED/WORKS (BFEB-12-114). Condition is Used. Shipped with FedEx Ground or FedEx Home Delivery. ABOUT US Faith Farm Ministries has been standing on the front lines in the war against addiction for 69 years. Our 10-month, men’s and women’s addiction recovery program, focuses strongly on the believer’s Biblical identity in Christ and being transformed by the renewing of the mind to the amazing Truth of the Gospel. Our program operates by a “thrift store” model, depending upon the Lord to provide our resources through donations of used saleable furniture, clothing, other household goods and unrestricted cash donations by the people in our community. This allows us to provide the program free of charge to those who come seeking recovery. “The Farm” serves up to 450 men and women from all walks of life, from every corner of the country, from every ethnicity and denominational background, who all come to seek recovery through a life in union with Jesus Christ and the power of the Holy Spirit. Our curriculum is accredited through our close partnership with a local Bible College & Seminary and we believe we are the only recovery mission in the world with college-accredited curriculum. Your purchase today provides direct support to the recovery of hundreds of sons, brothers, husbands, dads, daughters, sisters, wives & moms, and helps us to continue to minister salvation, healing, restoration, and hope. Thank you for bidding, thank you for buying, thank you for your prayers, and thank you for supporting Faith Farm Ministries.© 2020 Faith Farm Ministries. | All Rights Reserved |9538 US Hwy 441 Boynton Beach, FL 33472 | Fort Lauderdale Rescue Tabernacle, Inc., d/b/a Faith Farm Ministries is a 501(c)(3) organization.

Up for sale is my pristine Emotiva DR-1 pair of true monoblock power Amps. Comes with everything to include OEM box so you know it will ship safe and sound Here is the specs: The XPA-DR1 is a true monoblock power amplifier, and features a single Differential Reference Amplifier Module, in a true monoblock configuration, powered by its own dedicated 3 kW switch mode power supply. The XPA-DR1 provides massive power, superb dynamics, incredible resolution, and absolute control. If you’re looking for the very best sound quality, with virtually endless reserves of power against a jet black noise floor, this is the amplifier for you. The XPA-DR1 delivers 650 watts RMS into 8 Ohms, and 1000 watts RMS (that’s 1 kW) into 4 Ohms, with less than 0.1% THD. The Power Supply: The Foundation Of A Great Amplifier In amplifier design, everything starts with the power supply. The XPA-DR1 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions.

This Emotiva XPA-5 Gen 1 5-channel power amplifier is perfect for your home audio setup. It delivers high-quality sound with precise clarity and detail. With its sleek design, this power amplifier is a great addition to any home entertainment system. It is easy to use and provides an exceptional listening experience. Slight scratch/indent on top in pic.

Up for sale is my pristine Emotiva DR-1 pair of true monoblock power Amps. Comes with everything to include OEM box so you know it will ship safe and sound Here is the specs: The XPA-DR1 is a true monoblock power amplifier, and features a single Differential Reference Amplifier Module, in a true monoblock configuration, powered by its own dedicated 3 kW switch mode power supply. The XPA-DR1 provides massive power, superb dynamics, incredible resolution, and absolute control. If you’re looking for the very best sound quality, with virtually endless reserves of power against a jet black noise floor, this is the amplifier for you. The XPA-DR1 delivers 650 watts RMS into 8 Ohms, and 1000 watts RMS (that’s 1 kW) into 4 Ohms, with less than 0.1% THD. The Power Supply: The Foundation Of A Great Amplifier In amplifier design, everything starts with the power supply. The XPA-DR1 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions.

Up for sale is my pristine Emotiva DR-1 pair of true monoblock power Amps. Comes with everything to include OEM box so you know it will ship safe and sound Here is the specs: The XPA-DR1 is a true monoblock power amplifier, and features a single Differential Reference Amplifier Module, in a true monoblock configuration, powered by its own dedicated 3 kW switch mode power supply. The XPA-DR1 provides massive power, superb dynamics, incredible resolution, and absolute control. If you’re looking for the very best sound quality, with virtually endless reserves of power against a jet black noise floor, this is the amplifier for you. The XPA-DR1 delivers 650 watts RMS into 8 Ohms, and 1000 watts RMS (that’s 1 kW) into 4 Ohms, with less than 0.1% THD. The Power Supply: The Foundation Of A Great Amplifier In amplifier design, everything starts with the power supply. The XPA-DR1 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions.

See full item description, click here. Listed by Frooition Frooition | No-js Template | eBay design, eBay store design, eBay shop design, eBay template design, eBay listing design, eBay Listing Tool (ver:froo_no_js)

Emotiva XPA-6 Gen 3 Power AmplifierSIX | 6.0 200 Watts per ChannelLike new, very lightly used. Excellent, extremely clean condition. Works perfectly with no issues. Includes power cord, trigger cable and manual. Ships within 24-hours, usually same day. (from a smoke-free, pet-free environment) Fast Shipping!

1 Pair of Emotiva XPA HC1 Class A/B Mono Block Amplifiers 300 Watts @ 8 Ohms. I purchased these last March and are still under the manufacturers warranty (5Yrs total) Items are in great condition . Comes with original boxes and all paperwork. Specs: https://emotiva.com/products/hc-1

1 Pair of Emotiva XPA HC1 Class A/B Mono Block Amplifiers 300 Watts @ 8 Ohms. I purchased these last March and are still under the manufacturers warranty (5Yrs total) selling due to upgrading to a pair of much more expensive tube amplifiers. Comes with original boxes and all paperwork. Specs: https://emotiva.com/products/hc-1

Emotiva XPA-100 Mono amp- Audiophile mono block (one channel) amplifier; 400 watts at 4 Ohms; 250 watts at 8 Ohms- Fully discrete signal path, with class A/B output stage and massive power reserves- Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring I bought this about 8 years to power my center channel, I am down sizing and no longer need it. Comes with the owners manual and power cord.

Circuit TopologyA fully modular, fully differential, fully balanced audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection.NOTE: This is a fully balanced amplifier with a floating, differential output stage. The output terminals must NEVER be tied together or ground referenced. Doing so will cause immediate damage that is NOT covered under warranty. If you have any questions about speaker compatibility, please contact Emotiva for technical support.Audio SpecificationsThe XPA-DR1 features one Differential Reference™ Amplifier Module. Audio Specifications (One Differential Reference Amplifier Module):Power Output: 650 watts RMS into 8 Ohms at <0.1% THD. 1000 watts RMS into 4 Ohms at <0.1% THD.Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB).Broad Band Frequency Response: 20 Hz to 50 kHz +0/-2 dB.THD + noise: < 0.015%; at 100 watts RMS; 1 kHz; 8 Ohms.Signal to Noise Ratio (8 Ohm load): > 122 dB; ref FTC rated power; unbalanced input (A-weighted). > 96 dB; ref 1 watt; unbalanced input (A-weighted).Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads).Damping Factor (8 Ohm load): > 500.Input Sensitivity (for rated power; 8 Ohm load): 2.4 V.Gain: 29 dB.Maximum Power Consumption: 1,000 watts. Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore they are not at all characteristic of what you would expect when playing music or the sound track from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered to be a circuit requirement for normal operation.Input Impedance: 33 kOhms (balanced). 23.5 kOhms (unbalanced).Input And Output ConnectionsInput Connections: Unbalanced (RCA); balanced (XLR); one each, user selectable.Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.Trigger: Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA.Power RequirementsBetween 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).Front Panel Controls and IndicatorsStandby: push button (halo ring changes color to indicate Standby or On).Status LEDs: one per channel; blue. Status LEDs change to red to indicate a fault condition.Rear Panel ControlsAC Power switch: rocker switch (switches AC main power).Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs.Circuit Breaker: press button to reset circuit breaker.ProtectionThe XPA-DR1 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.MechanicalDimensions: 17” wide x 8” high x 19” deep (unboxed; including feet). 17” wide x 7” high x 19” deep (unboxed; without feet). 24-1/2” wide x 12” high x 24-3/4” deep (boxed).Weight: 35.5 lbs (unboxed). 40.5 lbs (boxed).

Up for sale is my pristine Emotiva DR-1 pair of true monoblock power Amps. Comes with everything to include OEM box so you know it will ship safe and sound Here is the specs: The XPA-DR1 is a true monoblock power amplifier, and features a single Differential Reference Amplifier Module, in a true monoblock configuration, powered by its own dedicated 3 kW switch mode power supply. The XPA-DR1 provides massive power, superb dynamics, incredible resolution, and absolute control. If you’re looking for the very best sound quality, with virtually endless reserves of power against a jet black noise floor, this is the amplifier for you. The XPA-DR1 delivers 650 watts RMS into 8 Ohms, and 1000 watts RMS (that’s 1 kW) into 4 Ohms, with less than 0.1% THD. The Power Supply: The Foundation Of A Great Amplifier In amplifier design, everything starts with the power supply. The XPA-DR1 features a custom-configured version of our high-current switch mode power supply (SMPS) - a lightweight, powerful, intelligent design capable of delivering over 3 kW of continuous power with absolute reliability and extremely high efficiency. Our cutting edge SMPS offers the dynamic attributes of a classic transformer-based design with none of the drawbacks. Like the best transformer-based power supplies, our SMPS delivers plenty of continuous power to enable our amplifier modules to live up to their full performance potential, and plenty of dynamic power to ensure that musical peaks will never be compressed or limited. However, compared to transformer-based designs, our SMPS is lighter and more efficient; it’s also fully regulated, which ensures optimum performance under a wider range of load conditions.

this is the big one, differentiail reference unit, super heavy, i will double box it, but as with my other auctions I will insure it for the purchase price, I will not be responsible if the shipper damages the package, its been alot lately, and not at the fault of BHB, we over pack if anything.

this is the big one, differentiail reference unit, super heavy, i will double box it, but as with my other auctions I will insure it for the purchase price, I will not be responsible if the shipper damages the package, its been alot lately, and not at the fault of BHB, we over pack if anything.

Emotiva XPA1 Gen 2 Monoblock Amplifier Pair XLNT Hard To Find! Easily the most desirable of Emotiva’s high power amplifier line since they began producing them and NO LONGER available as Emotiva has switched to class D designs. The Gen 2 model builds on the original XPA-1 Monoblocks with a massive 600w power rating at 8ohm and 1000w at 4. There is likely no speaker that these monsters can not handle with aplomb. Have been previously handling a pair of Revel Studio 2 listed separately. Additionally, the Gen 2 model Can be run in straight class A mode via a front panel switch. This particular pair is in excellent overall cosmetic condition with some minor nicks and very light scratches in a few spots. NEVER in a smoking household and never abused, these have been lovingly cared for and sound sonically excellent as well. Ready to take your audio system home theater setup to the next level. Includes original boxes, packing and power cables. Due to weight these are LOCAL PICKUP ONLY.

My girlfriend is moving in with me and I have to downsize my hifi gear.Therefore, Im selling my beloved pair of Emotiva XPA-1 One 2 power amplifiers. They are in mint condition without any scratches and I have the original packaging. This is a pair of very powerful amplifiers that can be driven in pure class A or in A/B. https://hometheaterhifi.com/reviews/amplifier/power-amplifier/emotiva-xpa-1-gen-2-monoblock-power-amplifier-review/ The price is for a pair and I can bring it to Germany close to the Swiss border for EU buyers but due to the weight I cant offer shipping.

The power amplifier performs the simple but critical job of boosting the output signals from each channel of your stereo preamp or surround sound processor to the level necessary to drive your loudspeakers. While this may seem trivial, a really good power amp is essential to having a great audio system, because any flaws in the performance of your power amp are going to limit the performance of your entire system. Every amplifier in the new Third Generation XPA series was carefully designed to deliver superb technical performance, unsurpassed sound quality, and an exceptionally accurate and dynamic rendition of all types of music, thus ensuring that your entire system will sound its absolute best. Each individual XPA amplifier is modular, and can be customized to provide exactly the power and number of channels you need today, and expanded later if your needs change; and multiple matching chassis enable you to add even more channels, or more power, for a near endless variety of options. The new XPA-11 is an eleven-channel audiophile quality power amplifier. The XPA-11 is populated with three of our High-Powered Single Channel Modules, and four of our Stereo Modules, for a total of three high-powered channels and eight lower-powered channels. This combination is ideal for a surround sound system that is used for both music and home theater listening, and includes height speakers. The three front speakers, which are the most critical for both music and home theater listening, are powered by the three high-powered channels. The surround channels, and the height channels, are driven by the lower powered stereo modules. Even though the channels differ in terms of maximum power output, they feature perfectly matched electrical characteristics, and the same superb Class A/B sound quality. The XPA-11 is perfect for powering:A 7.1.4 or 5.1.6 Dolby Atmos or DTS-X systemA 7.1 or 7.2 channel system that also includes two pairs of smaller speakers in other zonesConfiguration: 3 x High-Powered Single-Channel Modules4 x Stereo ModulesThe power output capabilities of the various channels on the XPA-11 were optimized to provide the best sound quality in real-world listening conditions; the front channels, which are the most critical for both dynamic music reproduction and crystal clear dialog, receive the most power. (This is especially the case if your system features large tower speakers in the front, a large center channel speaker, bookshelf or wall mounted surrounds, and ceiling mounted height speakers.) Power output (High-Powered Single Channel Modules):300 watts/channel RMS into 8 Ohms; two channels driven490 watts/channel RMS into 4 Ohms; two channels drivenPower output (Stereo Modules): 65 watts/channel RMS into 8 Ohms; two channels driven 100 watts/channel RMS into 4 Ohms; two channels drivenWhy You Need A Dedicated Power AmplifierMost experts agree that, if you want the absolute best sound quality and technical performance, separate components are the way to go. Our new Third Generation XPA series power amplifiers are all designed from the ground up to perform a single critical task – to accurately reproduce every detail and nuance of your music. By focusing all of our efforts on that one goal, we’ve been able to design an amplifier that performs its job with remarkable precision, and avoids most of the compromises that limit lesser designs. Experience Meets Cutting Edge TechnologyWhen we set out to design the latest version of our XPA series of amplifiers, we analyzed everything in every amplifier we’ve ever made, from front to back, inside and out. By combining years of design experience, with a thorough understanding of recent advances in audio technology, we were able to determine several areas where we could improve on our previous designs. After carefully weighing all the options, we kept the best features of our previous models, added some new technology where we determined it would actually deliver significant improvements, and optimized several operating parameters to ensure that it would all work together flawlessly. The new Third Generation represents a significant improvement for our highly acclaimed XPA series of amplifiers – and delivers improvements in both technical performance and sound quality.All of the models in our new Third Generation XPA amplifier family are designed to reproduce today’s high definition movie sound tracks and music sources with awesome realism, amazing finesse and precision, and without the slightest hint of strain or signal compression. They deliver a listening experience that is far above anything you can achieve with multi-purpose components like receivers, or with other amplifiers in their modest price range. We’re talking about real-world power and fidelity that you can immediately hear and appreciate. Designed and Assembled in the USA with Globally Sourced ComponentsAll of our new Third Generation XPA power amplifiers, including the XPA-11, are designed, assembled, and tested in the USA. Assembling products here in the USA gives us exceptional control over every facet of the design and production process, which helps us build the highest quality products for our customers while minimizing unnecessary complications and production delays. Each Emotiva amplifier is carefully designed with premium components to deliver a stunningly capable, reliable, and refined system. Note: To ensure that amplifier channels are always installed properly, and function to our specifications, amplifier modules must be installed by Emotiva, or by your local authorized Emotiva service representative.FEATURED SPECIFICATIONSAudioPower output (High-Powered Single Channel Modules): 300 watts/channel RMS into 8 Ohms; two channels driven | 490 watts/channel RMS into 4 Ohms; two channels drivenPower output (Stereo Modules): 65 watts/channel RMS into 8 Ohms; two channels driven | 100 watts/channel RMS into 4 Ohms; two channels drivenAudiophile quality Class A/B output stage.Balanced and unbalanced inputs for compatibility with a wide variety of preamps and surround sound processors.Design TopologyClass A/B output stage; Optimized Class H power supply topology on High-Powered Single Channel Modules for improved efficiency.Regulated switch mode power supply combines massive power capability, high reliability, excellent performance, and reduced weight.FeaturesFully modular construction for optimum flexibility.Universal AC power automatically selects the proper line voltage for easy installation in a wide variety of locations.Comprehensive yet transparent protection circuitry protects from most common fault conditions without degrading sound quality. HardwareDimensions: 17” x 19” x 8” (including feet) Weight: 53 pounds (unboxed) Power Requirements: 100 – 250 VAC 50/60 Hz (automatically detected).

Emotiva Audio XPA-100 Gen 2 - Mono Block Power Amplifier, 400 Watts at 4 Ohm. XLR / RCA Input Single Owner, no issues with this amp, rock solid, quiet, no fans, runs cool even at full loads. Audiophile mono block (one channel) amplifier; 400 watts at 4 Ohms; 250 watts at 8 Ohms Fully discrete signal path, with class A/B output stage and massive power reserves Balanced and unbalanced inputs; dual full-sized speaker outputs to facilitate bi-wiring. I dont have the 4 feet for this unit, but they are not needed unless you are stacking amps. Generic feet can added easily.This amp has the Grey front panels, not the standard black ones on the Gen-2, but this is a Gen-2 Model.

Emotiva XPA HC-1 High Current Monoblock Amplifier. Mint condition. Local pickup only, no shipping.