MSRP: $25,000 for the pair Used, mint condition Uses IEC C19 power cables (Included) Including extra set of tubes. Ships in original box. Will ship individually (two separate packages) @ 90 lbs each, totaling 180 lbs. Since any listing 150 lbs and above is required by eBay to be classified as freight, and these will not be shipped freight, the initial shipping price is not accurate. Please DO NOT PAY without receiving an accurate quote from us. Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

MSRP: $25,000 for the pair Used, mint condition Uses IEC C19 power cables (Included) Including extra set of tubes. Ships in original box. Will ship individually (two separate packages) @ 90 lbs each, totaling 180 lbs. Since any listing 150 lbs and above is required by eBay to be classified as freight, and these will not be shipped freight, the initial shipping price is not accurate. Please DO NOT PAY without receiving an accurate quote from us. Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

MSRP: $25,000 for the pair Used, mint condition Uses IEC C19 power cables (Included) Including extra set of tubes. Ships in original box. Will ship individually (two separate packages) @ 90 lbs each, totaling 180 lbs. Since any listing 150 lbs and above is required by eBay to be classified as freight, and these will not be shipped freight, the initial shipping price is not accurate. Please DO NOT PAY without receiving an accurate quote from us. Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

MSRP: $25,000 for the pair Used, mint condition Uses IEC C19 power cables (Included) Including extra set of tubes. Ships in original box. Will ship individually (two separate packages) @ 90 lbs each, totaling 180 lbs. Since any listing 150 lbs and above is required by eBay to be classified as freight, and these will not be shipped freight, the initial shipping price is not accurate. Please DO NOT PAY without receiving an accurate quote from us. Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

MSRP: $25,000 for the pair Used, mint condition Uses IEC C19 power cables (Included) Ships in original box. Will ship individually (two separate packages) @ 90 lbs each, totaling 180 lbs. Since any listing 150 lbs and above is required by eBay to be classified as freight, and these will not be shipped freight, the initial shipping price is not accurate. Please DO NOT PAY without receiving an accurate quote from us. Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

MSRP: $25,000 for the pair Used, mint condition Uses IEC C19 power cables (Included) Ships in original box. Will ship individually (two separate packages) @ 90 lbs each, totaling 180 lbs. Since any listing 150 lbs and above is required by eBay to be classified as freight, and these will not be shipped freight, the initial shipping price is not accurate. Please DO NOT PAY without receiving an accurate quote from us. Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

MSRP: $12,500 Used, mint condition Uses IEC 19 power cable (Included) Manual: https://audioresearch.com/wp-content/uploads/2021/08/REF250_Manual.pdf Specifications: POWER OUTPUT: 250 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 250 watts, below .04% at 1 watt. Approximate actual power available at “clipping” 270 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.) POWER BANDWIDTH: (-3dB points) 5Hz to 70kHz. FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.5Hz to 110 kHz. INPUT SENSITIVITY: 2.4V RMS Balanced for rated output. (25.5 dB gain into 8 ohms.) INPUT IMPEDANCE: 200K ohms Balanced. OUTPUT TAPS: 4, 8, 16 ohms. OUTPUT REGULATION: Approximately 0.9dB 16 ohm load to open circuit (Damping factor approximately 10). OVERALL NEGATIVE FEEDBACK: 8.8dB. SLEW RATE: 20 volts/microsecond. RISE TIME: 1.5 microseconds. HUM & NOISE: Less than 0.2mV RMS – 110dB below rated output (IHF-A weighted, input shorted, 16 ohm output). POWER SUPPLY ENERGY STORAGE: Approximately 900 joules. POWER REQUIREMENTS: 105-130VAC 60Hz (260- 250VAC 50Hz) 770 watts at rated output, 1000 watts maximum, 380 watts at “idle,” 1 watt off. TUBES REQUIRED: 3 Matched pair KT120 (Power output V1-6); 1 Matched pair KT120 (Driver V8- 9); 2 6H30 (Gain stage V7 and Regulator Driver V10); 1 6550C (Regulator V11). DIMENSIONS: 19 (48.3 cm) W x 8.75 (22.2 cm) H x 19.5 (49.5 cm) D. Handles extend 1.5 (3.8 cm) forward Important Note on Shipping: eBay estimates of shipping costs are not accurate and do not include insurance or adult signature requirement. Please contact us for a more accurate quote. No shipping to Vietnam, China or Hong Kong. Please do not submit payment until you have received an invoice from us with accurate shipping costs. We reserve the right to hold the item or cancel the transaction if actual shipping costs are not paid.

Amplifier Audio Research reference 110 For sale Power amplifier Audi? Research REFERENCE high definition.220 v. POWER OUTPUT110 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.3% at 110 watts, below .003% at 1 watt. Approximate actual power available at clipping: 120 watts (1 kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, the maximum power will be adversely affected, although a listening standpoint this is not very critical.) POWER BANDWIDTH( -3dB) 12Hz to 60kHz.FREQUENCY RESPONSE(-3dB at 1 watt) 0.6Hz to 90kHz. INPUT SENSITIVITY1.8V RMS BAL for rated output. (24dB Bal gain into 8 ohms.) INPUT IMPEDANCE300K ohms Balanced.OUTPUT TAPS4, 8 and 16 ohms OUTPUT REGULATIONApproximately 0.7dB 16 ohm load to open circuit OVERALL NEGATIVE FEEDBACK12dBDAMPING FACTORApproximately 12DISTORTION-SLEW RATE10 V/µsRISE TIME3.5 µsHUM & NOISELess than 0.2mV RMS -106dB below rated output (IHF weighted, input shorted). POWER SUPPLY ENERGY STORAGEApproximately 520 joules.POWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 630 watts at rated output, 800 watts maximum, 410 watts at idle. For those confused by the variety of devices from AR, I will explain that only the REFERENCE series actually plays,all the rest just sound somehow.This machine plays!You could even say it sings!Yes, AR has its own sound and its own vision of the process, but if youve ever heard the right path with AR, you wont exchange it for any other.It is not for nothing that the company actually stood at the origins of Hi End, like McIntosh, Krell, etc. and still exists. In general, you need to select the right components for it at its level and you will get sound of such quality that I think audio happiness is guaranteed to you. The amplifier is in excellent condition, no breakdowns and has no problems and I am sure will not have any.

Synergistic Research Orange Reference Audiophile Fuse 20mm T10A. Mit OVP

Referencia absoluta.y embalaje original. Una etapa tiene vlvulas kt 120 como nuevas!! . Muy pocas horas. Puestas en Sarte Audio .