Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World (e.g. India, Malaysia, Brasil, UAE, Canada, Australia, and all other countries outside of Europe, not mentioned in a separate item) - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World (e.g. India, Malaysia, Brasil, UAE, Canada, Israel, Australia, and all other countries outside of Europe, not mentioned in a separate item) - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Original Bedienungsanleitung für Verstärker Akai AM-35 in deutsch.Gedruckt in Japan.Guter Zustand, gelocht. Verkauf von Privat ohne Gewährleistung/Garantie.Keine Rücknahme.

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Original Bedienungsanleitung für Verstärker Akai AM-35 in deutsch.Gedruckt in Japan.Guter Zustand, gelocht. Verkauf von Privat ohne Gewährleistung/Garantie.Keine Rücknahme.

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Vor dem Verkauf wurde der Artikel auf seine Funktion überprüft. Den optischen Zustand können Sie den beigefügten Bildern entnehmen. Versand und Paypal sind möglich bei Kosten Übernahme. Bevorzugt ist eine Abholung. Bei etwaigen Fragen stehe ich Ihnen gerne zur Verfügung. Auslandsversand ist nur nach vorheriger Anfrage und eindeutiger Bestätigung durch mich möglich. Der Artikel wird sorgfältig verpackt, dennoch liegt die Verantwortung beim Käufer. Abholung ist die bevorzugte Option für beide Seiten. Schauen Sie auch gerne bei meinen anderen Auktionen vorbei – es gibt viel zu entdecken! Viel Spaß beim Stöbern! Bitte beachten Sie aus rechtlichen Gründen, dass es sich hierbei um einen Privatverkauf handelt und daher keine Gewährleistung oder Rückgaberecht gewährt wird. Gemäß geltendem EU-Recht handelt es sich um einen Privatverkauf nach §13 BGB, ohne jegliche Gewährleistung oder Rücknahme. Durch die Abgabe eines Gebots erklärt sich der Bieter ausdrücklich mit diesen Bedingungen einverstanden.

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Der AKAI AM-35 Stereo Receiver bietet ein hervorragendes Klangerlebnis für Musikliebhaber. Mit seiner Marke Akai und seiner Produktart als Stereo Receiver ist dieser Receiver perfekt für Musikliebhaber, die nach einer qualitativ hochwertigen Audioausgabe suchen. Der Receiver bietet eine Leistung von 35 Watt pro Kanal und verfügt über eine Fülle von Eingängen für verschiedene Audioquellen. Die Bedienung ist einfach und intuitiv, so dass Sie Ihre Musik ohne Komplikationen genießen können. Ein großartiges Produkt für jeden, der sich für Audioqualität begeistert.

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Der AKAI AM-35 Stereo Receiver bietet ein hervorragendes Klangerlebnis für Musikliebhaber. Mit seiner Marke Akai und seiner Produktart als Stereo Receiver ist dieser Receiver perfekt für Musikliebhaber, die nach einer qualitativ hochwertigen Audioausgabe suchen. Der Receiver bietet eine Leistung von 35 Watt pro Kanal und verfügt über eine Fülle von Eingängen für verschiedene Audioquellen. Die Bedienung ist einfach und intuitiv, so dass Sie Ihre Musik ohne Komplikationen genießen können. Ein großartiges Produkt für jeden, der sich für Audioqualität begeistert.

Akai AM-35, Hi-Fi Audio Amplifier. Fully functional. Very good Made in Japan, 1990 - 1991. Original price (1991): DM 600, GBP 200, USD 380. Audio Power at 8 Ohm: 2 x 60 W DIN, or 2 x 90 W music Audio Power at 4 Ohm: 2 x 90 W DIN, or 2 x 130 W music Frequency band: 10 Hz - 60 kHz Total Harmonic Distortion: 0.005 % Signal-to-Noise ratio: 100 dB Inputs: Phono (MM), Tuner, CD, Aux, Tape 1, Tape 2, Tape 3 Outputs: Tape 1 (Rec), Tape 2 (Rec), Tape 3 (Rec), Headphones, 2 sets of Loudspeaker boxes Speakers: 4, 8 or 16 Ohm Tone controls: Bass (10 Hz) ± 8 dB, Treble (100 kHz) ± 8 dB, Subsonic filter Voltage: 220 V Dimensions: width 42.5 cm (16.7), depth 37 cm (14.6), height 15.6 cm (6.1) Weight: 9.6 kg (21 lbs) On offer is a classic Akai AM-35 integrated Hi-Fi amplifier. The model AM-35 is built entirely with Japanese discrete transistors, without integrated circuits in the amplifier or driver stages. Only the input equalizer for the phono stage and the tone control stage are each built around one Mitsubishi M5220P low-noise, low-distortion operational amplifier of low integration (two op-amps in one 8-pin package). The Akai AM-35 amplifier has a classic schematic – a push-pull end-stage with fully complementary power and driver transistor pairs, and a differential pre-driver stage. The pre-amp circuit is direct-coupled to Toshiba 2SK170BL J-FET transistors of vanishingly low noise figure. Direct coupling eliminates input capacitors, and the phase distortion they would introduce. The output power is delivered by Sanken 2SC3855 (NPN) and 2SA1491 (PNP) complementary transistors. The output transistors are mounted on a large aluminium heat-sink, and the amplifier case permits good natural ventilation. There is no fan to produce noise. The design with discrete components, direct coupling and fully complementary semiconductors serves for linearity of amplification. Indeed, the sound of the AM-35 is very precise, clean, not colored. The amplifier delivers an increasing power gracefully – without signs of fatigue, such as increasing noise or distortion. The amplifier has a standard set of tone controls and correctors, e.g. a subsonic filter, variable treble and bass controls, and a RIAA-correction of the Phono input (moving magnet). The Akai AM-35 has also a handy input/output switchboard, which enables the playback, record and tape-dubbing without reconnecting cables. With this amplifier, one can: - play a vinyl record and send the signal to a computer to digitally record it; - play a compact disk or cassette and send the signal to record it on a reel-to-reel tape deck. With a 3-head deck, one can listen to the new recording while it is being made; - connect an external equalizer (or sound processor) after all inputs and before the power amplifier (loop), e.g. use the Tape 3 Rec/Play connectors. If the equalizer itself has a Tape Play/Rec input/output and switch, the options become even richer. The correct cable connections and switches positions are explained in words and diagrams in the Akai Owners Manual (enclosed in the package). The amplifier can operate two sets of loudspeaker boxes – A and B. The sets can be independently switched on and off from the front panel. The amplifier construction is very solid, with an aluminium front panel, and knobs and handles of massive plastic in satin finish. The power switch and the inputs switchboard are equipped with indicator lights. The output connectors are sturdy color-coded screws (no spring clips), where the loudspeaker cables can be fastened reliably. The amplifier operates with a protective switch-on delay of a few seconds, and has a built-in overload protection. The sound is clean and precise, with bright treble, detailed mid-range, and natural, smooth bass. The amplifier is fully functional, with all controls, indicators and connectors in good working condition. The amplifier is in a very good cosmetic condition – without scratches, dents, peeled or rusted spots, without any odour or discoloration. There is a very minor, hair-thin wear of the black paint along a short stretch of the top rim of the front panel. There is a minor scratch on the back of the top panel (left edge). The spots are shown in close-up on two of the photos. The amplifier has been used carefully, in a smoke-free and pet-free household, at room temperature. The case was thoroughly cleaned inside and out. All switches, selectors and potentiometers were pump-dusted and deoxidized. I am selling the amplifier due to removal to a smaller apartment and downsizing my Hi-Fi system. The set contains: the Akai AM-35 amplifier two professional audio cables, with gold-plated RCA cinch connectors the Owners Manual (in English) the Service Manual (in English) with the amplifier schematic and circuit boards layout. The set will be packed in a sturdy cardboard box, protected with lots of elastic pads, styrofoam and soft wrapping. I will ship with BPost, DPD or GLS, in accordance with buyers choice. Once You buy the set, send me a message in eBay, of which shipping option You prefer. I will send You an eBay-invoice with the correct shipping cost, and You will pay on that invoice. Thank You! Economy shipping with DPD: to Belgium - $ 9 to Germany, Netherlands, Luxembourg - $ 15 to France, UK, Denmark, Austria, Italy, Poland - $ 25 to Spain, Portugal, Sweden, Finland - $ 32 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 35 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 53 to Ireland, Greece - $ 44 Economy shipping with BPost: to Belgium - $ 12 to France, Germany, Netherlands, Luxembourg - $ 45 to EU countries - $ 92 to Europe - $ 115 to USA, Mediterranean - $ 145 to rest of the World - $ 230 Economy shipping with GLS: to Belgium - $ 9 to France, Germany, Netherlands, Luxembourg - $ 22 to Denmark, Austria, Italy, Poland - $ 31 to Spain, Portugal, Sweden, Finland, Ireland - $ 41 to Hungary, Czech Republic, Slovakia, Slovenia, Croatia - $ 44 to Estonia, Latvia, Lithuania, Romania, Bulgaria - $ 73

Der AKAI AM-35 Stereo Receiver bietet ein hervorragendes Klangerlebnis für Musikliebhaber. Mit seiner Marke Akai und seiner Produktart als Stereo Receiver ist dieser Receiver perfekt für Musikliebhaber, die nach einer qualitativ hochwertigen Audioausgabe suchen. Der Receiver bietet eine Leistung von 35 Watt pro Kanal und verfügt über eine Fülle von Eingängen für verschiedene Audioquellen. Die Bedienung ist einfach und intuitiv, so dass Sie Ihre Musik ohne Komplikationen genießen können. Ein großartiges Produkt für jeden, der sich für Audioqualität begeistert.

Der AKAI AM-35 Stereo Receiver bietet ein hervorragendes Klangerlebnis für Musikliebhaber. Mit seiner Marke Akai und seiner Produktart als Stereo Receiver ist dieser Receiver perfekt für Musikliebhaber, die nach einer qualitativ hochwertigen Audioausgabe suchen. Der Receiver bietet eine Leistung von 35 Watt pro Kanal und verfügt über eine Fülle von Eingängen für verschiedene Audioquellen. Die Bedienung ist einfach und intuitiv, so dass Sie Ihre Musik ohne Komplikationen genießen können. Ein großartiges Produkt für jeden, der sich für Audioqualität begeistert.

Akai AM-35 edler Stereo Vollverstärker Geprüft und getestet: Voll funktionsfähig Guter Zustand, leichte Gebrauchsspuren vorhanden, Netzkabelhalterung am Gerät wackelt etwas, technisch ohne Einfluss, siehe Bilder. Zustand wie abgebildet siehe Bilder. Bitte beachten Sie die Bilder, diese sind Teil der Artikelbeschreibung. Lieferumfang wie abgebildet Ohne weiteres Zubehör! Keine Fernbedienung! Keine Anleitung! Versandkosten beziehen sich auf den Versand innerhalb Deutschlands Internationale Versandkosten bitte vor dem Kauf erfragen! Worlwide Shipping!!! Please ask for the shipping costs to your Country : ) !

Der AKAI AM-35 Stereo Receiver bietet ein hervorragendes Klangerlebnis für Musikliebhaber. Mit seiner Marke Akai und seiner Produktart als Stereo Receiver ist dieser Receiver perfekt für Musikliebhaber, die nach einer qualitativ hochwertigen Audioausgabe suchen. Der Receiver bietet eine Leistung von 35 Watt pro Kanal und verfügt über eine Fülle von Eingängen für verschiedene Audioquellen. Die Bedienung ist einfach und intuitiv, so dass Sie Ihre Musik ohne Komplikationen genießen können. Ein großartiges Produkt für jeden, der sich für Audioqualität begeistert.

AKAI AM-35 Stereo Integrated Amplifier Made in Japan!!! Allgemein Hersteller: AkaiModell: AM-35Typ: VollverstärkerBaujahre: 1990 - 1992Hergestellt in: JapanFarben: Schwarz Fernbedienung: neinLeistungsaufnahme: 500 W max.Abmessungen: 425 x 156 x 370 mm (BxHxT)Gewicht: 9,6 kgNeupreis ca.: 599 DM Normal 0 21 false false false DE X-NONE X-NONE Zustand: Gebraucht mit normalen Gebrauchsspuren. Technisch einwandfrei. Lieferumfang: wie abgebildet / OHNE weiteres Zubehör Bitte die restlichen technischen Daten im Internet anschauen,sowie die Bilder Da ich ein Privatverkäufer bin, schließe ich jegliche Garantie oder ein Umtauschrecht aus.