The Yamaha T-33 Natural Sound AM FM Stereo Mono Radio Tuner is a black digital tuner unit that supports FM and AM modes. It has stereo L/R RCA audio outputs and a power of 120 W. This unit is designed for home audio use and features a single output. The model is Yamaha T-33. It has been tested and confirmed to be in working condition. Condition is pre owned. This tuner is in very good condition with no visible flaws or defects. The exterior case is clean with no cracks or splits.

Proceeds of this sale go to Charity. Up for you consideration is a PAIR of what I am calling Yamaha M-60M Monoblock power amplifiers. They in good to fair used physical condition, functionally fully working and upgraded. These are upgraded stock Yamaha M-60 Stereo power amplifiers to Monoblocks. Ergo, you need both of these for a stereo set-up and both are part of this auction. I did the following to convert these into monoblocs.Set voltages 10% higher for additional power/ headroom.Upgraded Audio outputs transistors to 230v/ 16A devices that are used in the Krell/Dagostino Relentless amplifier. The OEMs are 140v devices. I selected these Sanken outputs to keep the Yamaha sonic signature.Old capacitors in the signal path were upgraded to Nichicon Muse. Other caps checked to make sure they were in spec.Base current and output current to the output stage has been doubled. Each monoblocs now has Eight output devices plus eight Regulators for a total of 16 power transistors per monobloc.Bias for lower heat operation is set at 2 watts pure Class A. ie it runs on 2 watts pure class A all the time.The standard Auto class A is fully functional. And raises this between 15-25 watts pure class A if you desire to heat up your room. With this setting please do not stack anything on top of the mono-blocks to impede cooling.Used the second (un-used) RCA input to be capacitor coupled. So you can now use the R input as DC coupled, and the L input as AC coupled. Furthermore, you can use this to daisy chain more amplifiers by putting signal into the R input, and getting an AC coupled signal out from the L RCA.Both Monoblocs were designed the same in terms of both have the Right channel configured as the Master, driving the left channel in parallel, thus you will only see right channel inputs and outputs in both units. Gold plated speaker posts installed. All Speaker A, B and C are user selectable as stock. (For normal operation, keep A + B engaged)New LEDs installed to replace worn out lamps. Meters calibrated.Voltage set at 110v at the rear, you may set it to 120v if you wish, to have the amplifier run cooler, however you will lose about 20watts of power at 8 ohms. I have used larger outputs to be able to run at higher voltages, and as long as you keep the amplifiers cool, there is no harm. I would not recommend leaving the amplifiers on for extended periods of time. It just reduces the life of the product. Condition:Mixed bag, both units are used and vintage, so they are not MINT. However, they are quite presentable.One of the units has some dents underneath, but not visible unless you turn it upside down. In the rear it has some cracked glass on the edges, not very visible unless to take a flashlight and look. Id say they are in fair condition overall. Some scratches commiserate with age are present. Glue issue mitigated, new caps in audio path. Good for another 20 years. This been fully tested, bias is set. Class-A bias confirmed. I tested full power into 4 ohms and prior to clipping gave me more than 400 watts into 4 ohms (one combined channel driven, ie one monoblock). At 8 ohms, it pumps out over 200 watts before clipping. (closer to 245watts) Essentially, I have parallel bridged both channels. Doubled the outputs from stock. The amplifier is now more stable into lower impedances. UPGRADED speaker posts on this unit. The are 5 way Banana binding posts. The OEM could only accept bare wire. You can now use Banana jacks, spades, inserts and bare wire. Sounds amazing, soft, delicate, detailed, most importantly, because of an upgrade I did (will share details with the new owner) the sound is warm and less steely, especially in the mids. Please note: The shipping price is for one Unit, so please factor in shipping for both units is 2x what ebay shows. Please see all photos and ask questions if in doubt!

Up for you consideration is a PAIR of what I am calling Yamaha M-60M Monoblock power amplifiers. They in good to fair used physical condition, functionally fully working and upgraded. I have upgraded a couple of stock Yamaha M-60 Stereo power amplifiers to Monoblocks. So, you need both of these for a stereo set-up. Both are part of this auction. I did the following to convert these into monoblocs. Set voltages 10% higher for additional power/ headroom.Upgraded Audio outputs to 230v/ 16A devices that are used in the Krell/Dagostino Relentless amplifier. The OEMs are 140v devices. I kept both Sanken outputs to keep the Yammy sonic signature.Old capacitors in the signal path upgraded to Nichicon Muse. Other caps checked to make sure they were in spec.Base current and output current to the output stage has been doubled. Each monoblocs now has Eight output devices plus eight Regulators for a total of 16 power transistors per monobloc.Bias for lower heat operation is set at 2 watts pure Class A. ie it runs on 2 watts pure class A all the time.The standard Auto class A is fully functional. And raises this between 15-25 watts pure class A if you desire to heat up your room. With this setting please do not stack anything on top of the mono-blocks to impede cooling.Used the second (un-used) RCA input to be capacitor coupled. So you can now use the R input as DC coupled, and the L input as AC coupled. Furthermore, you can use this to daisy chain more amplifiers by putting signal into the R input, and getting an AC coupled signal out from the L RCA.Both Monoblocs were designed the same in terms of both have the Right channel configured as the Master, driving the left channel in parallel, thus you will only see right channel inputs and outputs in both units. Gold plated speaker posts installed. All Speaker A, B and C are user selectable as stock. (For normal operation, keep A + B engaged)New LEDs installed to replace worn out lamps. Meters calibrated.Voltage set at 110v at the rear, you may set it to 120v if you wish, to have the amplifier run cooler, however you will lose about 20watts of power at 8 ohms. I have used larger outputs to be able to run at higher voltages, and as long as you keep the amplifiers cool, there is no harm. I would not recommend leaving the amplifiers on for extended periods of time. It just reduces the life of the product. Condition:Mixed bag, both units are used and vintage, so they are not MINT. However, they are quite presentable.One of the units has some dents underneath, but not visible unless you turn it upside down. In the rear it has some cracked glass on the edges, not very visible unless to take a flashlight and look. Id say they are in fair condition overall. Some scratches commiserate with age are present. Glue issue mitigated, new caps in audio path. Good for another 20 years. This been fully tested, bias is set. Class-A bias confirmed. I tested full power into 4 ohms and prior to clipping gave me more than 400 watts into 4 ohms (one combined channel driven, ie one monoblock). At 8 ohms, it pumps out over 200 watts before clipping. (closer to 245watts) Essentially, I have parallel bridged both channels. Doubled the outputs from stock. The amplifier is now more stable into lower impedances. UPGRADED speaker posts on this unit. The are 5 way Banana binding posts. The OEM could only accept bare wire. You can now use Banana jacks, spades, inserts and bare wire. Sounds amazing, soft, delicate, detailed, most importantly, because of an upgrade I did (will share details with the new owner) the sound is warm and less steely, especially in the mids. Please see all photos and ask questions if in doubt!

ONLY EU SHIPPING !!!! Yamaha JB-0029 Headphones Mono LUXEMBOURG : 7 EURNL : 10 EURFRANCE : 15 EUR (sauf DOM TOM)SPAIN : 18 EURGERMANY : 12 EURITALY : 18 EUR...ONLY EU SHIPPING !!!!

Up for you consideration is a PAIR of what I am calling Yamaha M-60M Monoblock power amplifiers. They in good to fair used physical condition, functionally fully working and upgraded. I have upgraded a couple of stock Yamaha M-60 Stereo power amplifiers to Monoblocks. So, you need both of these for a stereo set-up. Both are part of this auction. I did the following to convert these into monoblocs. Set voltages 10% higher for additional power/ headroom.Upgraded Audio outputs to 230v/ 16A devices that are used in the Krell/Dagostino Relentless amplifier. The OEMs are 140v devices. I kept both Sanken outputs to keep the Yammy sonic signature.Old capacitors in the signal path upgraded to Nichicon Muse. Other caps checked to make sure they were in spec.Base current and output current to the output stage has been doubled. Each monoblocs now has Eight output devices plus eight Regulators for a total of 16 power transistors per monobloc.Bias for lower heat operation is set at 2 watts pure Class A. ie it runs on 2 watts pure class A all the time.The standard Auto class A is fully functional. And raises this between 15-25 watts pure class A if you desire to heat up your room. With this setting please do not stack anything on top of the mono-blocks to impede cooling.Used the second (un-used) RCA input to be capacitor coupled. So you can now use the R input as DC coupled, and the L input as AC coupled. Furthermore, you can use this to daisy chain more amplifiers by putting signal into the R input, and getting an AC coupled signal out from the L RCA.Both Monoblocs were designed the same in terms of both have the Right channel configured as the Master, driving the left channel in parallel, thus you will only see right channel inputs and outputs in both units. Gold plated speaker posts installed. All Speaker A, B and C are user selectable as stock. (For normal operation, keep A + B engaged)New LEDs installed to replace worn out lamps. Meters calibrated.Voltage set at 110v at the rear, you may set it to 120v if you wish, to have the amplifier run cooler, however you will lose about 20watts of power at 8 ohms. I have used larger outputs to be able to run at higher voltages, and as long as you keep the amplifiers cool, there is no harm. I would not recommend leaving the amplifiers on for extended periods of time. It just reduces the life of the product. Condition:Mixed bag, both units are used and vintage, so they are not MINT. However, they are quite presentable.One of the units has some dents underneath, but not visible unless you turn it upside down. In the rear it has some cracked glass on the edges, not very visible unless to take a flashlight and look. Id say they are in fair condition overall. Some scratches commiserate with age are present. Glue issue mitigated, new caps in audio path. Good for another 20 years. This been fully tested, bias is set. Class-A bias confirmed. I tested full power into 4 ohms and prior to clipping gave me more than 400 watts into 4 ohms (one combined channel driven, ie one monoblock). At 8 ohms, it pumps out over 200 watts before clipping. (closer to 245watts) Essentially, I have parallel bridged both channels. Doubled the outputs from stock. The amplifier is now more stable into lower impedances. UPGRADED speaker posts on this unit. The are 5 way Banana binding posts. The OEM could only accept bare wire. You can now use Banana jacks, spades, inserts and bare wire. Sounds amazing, soft, delicate, detailed, most importantly, because of an upgrade I did (will share details with the new owner) the sound is warm and less steely, especially in the mids. Please see all photos and ask questions if in doubt!

Up for you consideration is a PAIR of what I am calling Yamaha M-60M Monoblock power amplifiers. They in good to fair used physical condition, functionally fully working and upgraded. I have upgraded a couple of stock Yamaha M-60 Stereo power amplifiers to Monoblocks. So, you need both of these for a stereo set-up. Both are part of this auction. I did the following to convert these into monoblocs. Set voltages 10% higher for additional power/ headroom.Upgraded Audio outputs to 230v/ 16A devices that are used in the Krell/Dagostino Relentless amplifier. The OEMs are 140v devices. I kept both Sanken outputs to keep the Yammy sonic signature.Old capacitors in the signal path upgraded to Nichicon Muse. Other caps checked to make sure they were in spec.Base current and output current to the output stage has been doubled. Each monoblocs now has Eight output devices plus eight Regulators for a total of 16 power transistors per monobloc.Bias for lower heat operation is set at 2 watts pure Class A. ie it runs on 2 watts pure class A all the time.The standard Auto class A is fully functional. And raises this between 15-25 watts pure class A if you desire to heat up your room. With this setting please do not stack anything on top of the mono-blocks to impede cooling.Used the second (un-used) RCA input to be capacitor coupled. So you can now use the R input as DC coupled, and the L input as AC coupled. Furthermore, you can use this to daisy chain more amplifiers by putting signal into the R input, and getting an AC coupled signal out from the L RCA.Both Monoblocs were designed the same in terms of both have the Right channel configured as the Master, driving the left channel in parallel, thus you will only see right channel inputs and outputs in both units. Gold plated speaker posts installed. All Speaker A, B and C are user selectable as stock. (For normal operation, keep A + B engaged)New LEDs installed to replace worn out lamps. Meters calibrated.Voltage set at 110v at the rear, you may set it to 120v if you wish, to have the amplifier run cooler, however you will lose about 20watts of power at 8 ohms. I have used larger outputs to be able to run at higher voltages, and as long as you keep the amplifiers cool, there is no harm. I would not recommend leaving the amplifiers on for extended periods of time. It just reduces the life of the product. Condition:Mixed bag, both units are used and vintage, so they are not MINT. However, they are quite presentable.One of the units has some dents underneath, but not visible unless you turn it upside down. In the rear it has some cracked glass on the edges, not very visible unless to take a flashlight and look. Id say they are in fair condition overall. Some scratches commiserate with age are present. Glue issue mitigated, new caps in audio path. Good for another 20 years. This been fully tested, bias is set. Class-A bias confirmed. I tested full power into 4 ohms and prior to clipping gave me more than 400 watts into 4 ohms (one combined channel driven, ie one monoblock). At 8 ohms, it pumps out over 200 watts before clipping. (closer to 245watts) Essentially, I have parallel bridged both channels. Doubled the outputs from stock. The amplifier is now more stable into lower impedances. UPGRADED speaker posts on this unit. The are 5 way Banana binding posts. The OEM could only accept bare wire. You can now use Banana jacks, spades, inserts and bare wire. Sounds amazing, soft, delicate, detailed, most importantly, because of an upgrade I did (will share details with the new owner) the sound is warm and less steely, especially in the mids. Please see all photos and ask questions if in doubt!

Zum Verkauf steht ein erstklassiger Yamaha Verstärker für extrem sauberen und warmen Klang. Modell: AX-630 Leistung: 220V / 430W / 50Hz * weitere technische Details entnehmen Sie bitte den Bildern Zustand: - gebraucht, aber gut erhalten - wird nicht mehr genutzt; zuletzt getestet am 02.01.2025 - aus tierfreiem Nichtraucherhaushalt

ONLY EU SHIPPING !!!! Yamaha JB-0029 Headphones Mono LUXEMBOURG : 7 EURNL : 10 EURFRANCE : 15 EUR (sauf DOM TOM)SPAIN : 18 EURGERMANY : 12 EURITALY : 18 EUR...ONLY EU SHIPPING !!!!

Up for you consideration is a PAIR of what I am calling Yamaha M-60M Monoblock power amplifiers. They in good to fair used physical condition, functionally fully working and upgraded. I have upgraded a couple of stock Yamaha M-60 Stereo power amplifiers to Monoblocks. So, you need both of these for a stereo set-up. Both are part of this auction. I did the following to convert these into monoblocs. Set voltages 10% higher for additional power/ headroom.Upgraded Audio outputs to 230v/ 16A devices that are used in the Krell/Dagostino Relentless amplifier. The OEMs are 140v devices. I kept both Sanken outputs to keep the Yammy sonic signature.Old capacitors in the signal path upgraded to Nichicon Muse. Other caps checked to make sure they were in spec.Base current and output current to the output stage has been doubled. Each monoblocs now has Eight output devices plus eight Regulators for a total of 16 power transistors per monobloc.Bias for lower heat operation is set at 2 watts pure Class A. ie it runs on 2 watts pure class A all the time.The standard Auto class A is fully functional. And raises this between 15-25 watts pure class A if you desire to heat up your room. With this setting please do not stack anything on top of the mono-blocks to impede cooling.Used the second (un-used) RCA input to be capacitor coupled. So you can now use the R input as DC coupled, and the L input as AC coupled. Furthermore, you can use this to daisy chain more amplifiers by putting signal into the R input, and getting an AC coupled signal out from the L RCA.Both Monoblocs were designed the same in terms of both have the Right channel configured as the Master, driving the left channel in parallel, thus you will only see right channel inputs and outputs in both units. Gold plated speaker posts installed. All Speaker A, B and C are user selectable as stock. (For normal operation, keep A + B engaged)New LEDs installed to replace worn out lamps. Meters calibrated.Voltage set at 110v at the rear, you may set it to 120v if you wish, to have the amplifier run cooler, however you will lose about 20watts of power at 8 ohms. I have used larger outputs to be able to run at higher voltages, and as long as you keep the amplifiers cool, there is no harm. I would not recommend leaving the amplifiers on for extended periods of time. It just reduces the life of the product. Condition:Mixed bag, both units are used and vintage, so they are not MINT. However, they are quite presentable.One of the units has some dents underneath, but not visible unless you turn it upside down. In the rear it has some cracked glass on the edges, not very visible unless to take a flashlight and look. Id say they are in fair condition overall. Some scratches commiserate with age are present. Glue issue mitigated, new caps in audio path. Good for another 20 years. This been fully tested, bias is set. Class-A bias confirmed. I tested full power into 4 ohms and prior to clipping gave me more than 400 watts into 4 ohms (one combined channel driven, ie one monoblock). At 8 ohms, it pumps out over 200 watts before clipping. (closer to 245watts) Essentially, I have parallel bridged both channels. Doubled the outputs from stock. The amplifier is now more stable into lower impedances. UPGRADED speaker posts on this unit. The are 5 way Banana binding posts. The OEM could only accept bare wire. You can now use Banana jacks, spades, inserts and bare wire. Sounds amazing, soft, delicate, detailed, most importantly, because of an upgrade I did (will share details with the new owner) the sound is warm and less steely, especially in the mids. Please see all photos and ask questions if in doubt!

Enhance your music experience with this Yamaha Powered Subwoofer. The 8-inch driver size and 70 watts RMS power provide a powerful bass effect, making it compatible with various brands and systems. The silver cube shape and plastic material add a touch of elegance to your home decor. This subwoofer comes with wired connectivity and RCA audio inputs, making it easy to connect to your Yamaha audio system. Its adjustable volume and impedance of 8 ohms ensure a smooth and clear sound. Upgrade your home audio experience with the Yamaha YST-SW030 model.

Up for you consideration is a PAIR of what I am calling Yamaha M-60M Monoblock power amplifiers. They in good to fair used physical condition, functionally fully working and upgraded. I have upgraded a couple of stock Yamaha M-60 Stereo power amplifiers to Monoblocks. So, you need both of these for a stereo set-up. Both are part of this auction. I did the following to convert these into monoblocs. Set voltages 10% higher for additional power/ headroom.Upgraded Audio outputs to 230v/ 16A devices that are used in the Krell/Dagostino Relentless amplifier. The OEMs are 140v devices. I kept both Sanken outputs to keep the Yammy sonic signature.Old capacitors in the signal path upgraded to Nichicon Muse. Other caps checked to make sure they were in spec.Base current and output current to the output stage has been doubled. Each monoblocs now has Eight output devices plus eight Regulators for a total of 16 power transistors per monobloc.Bias for lower heat operation is set at 2 watts pure Class A. ie it runs on 2 watts pure class A all the time.The standard Auto class A is fully functional. And raises this between 15-25 watts pure class A if you desire to heat up your room. With this setting please do not stack anything on top of the mono-blocks to impede cooling.Used the second (un-used) RCA input to be capacitor coupled. So you can now use the R input as DC coupled, and the L input as AC coupled. Furthermore, you can use this to daisy chain more amplifiers by putting signal into the R input, and getting an AC coupled signal out from the L RCA.Both Monoblocs were designed the same in terms of both have the Right channel configured as the Master, driving the left channel in parallel, thus you will only see right channel inputs and outputs in both units. Gold plated speaker posts installed. All Speaker A, B and C are user selectable as stock. (For normal operation, keep A + B engaged)New LEDs installed to replace worn out lamps. Meters calibrated.Voltage set at 110v at the rear, you may set it to 120v if you wish, to have the amplifier run cooler, however you will lose about 20watts of power at 8 ohms. I have used larger outputs to be able to run at higher voltages, and as long as you keep the amplifiers cool, there is no harm. I would not recommend leaving the amplifiers on for extended periods of time. It just reduces the life of the product. Condition:Mixed bag, both units are used and vintage, so they are not MINT. However, they are quite presentable.One of the units has some dents underneath, but not visible unless you turn it upside down. In the rear it has some cracked glass on the edges, not very visible unless to take a flashlight and look. Id say they are in fair condition overall. Some scratches commiserate with age are present. Glue issue mitigated, new caps in audio path. Good for another 20 years. This been fully tested, bias is set. Class-A bias confirmed. I tested full power into 4 ohms and prior to clipping gave me more than 400 watts into 4 ohms (one combined channel driven, ie one monoblock). At 8 ohms, it pumps out over 200 watts before clipping. (closer to 245watts) Essentially, I have parallel bridged both channels. Doubled the outputs from stock. The amplifier is now more stable into lower impedances. UPGRADED speaker posts on this unit. The are 5 way Banana binding posts. The OEM could only accept bare wire. You can now use Banana jacks, spades, inserts and bare wire. Sounds amazing, soft, delicate, detailed, most importantly, because of an upgrade I did (will share details with the new owner) the sound is warm and less steely, especially in the mids. Please see all photos and ask questions if in doubt!

Yamaha JB-0029 Kopfhörer Made in Japan Rar. Mono Super ! Yamaha JB-0029 Headphones Mono Super Rar . Super Sound !

Yamaha T-33 Natural Sound AM FM Stereo Mono Radio Tuner Tested Working.

Yamaha JB-0029 Kopfhörer Made in Japan Rar. Mono Super ! Yamaha JB-0029 Headphones Mono Super Rar . Super Sound !

This Yamaha Natural Sound MX M70 Mono Power Amplifier is a vintage amplifier that offers exceptional sound quality. With its black color and sleek design, it is a perfect addition to any home audio setup. The amplifier has one channel and one input, making it easy to use and set up. The MX-M70 is a reliable and durable power amplifier that is ideal for any music enthusiast. It is a great choice for those who want to experience high-quality sound without compromising on style. This amplifier is perfect for home use and is sure to impress any audiophile.

Yamaha JB-0029 Kopfhörer Made in Japan Rar. Mono Super ! Yamaha JB-0029 Headphones Mono Super Rar . Super Sound !

Analog Mono Input Board XQ114 ANI1-2Aus einem vollfunktionsfähigen Yamaha 02R Version 2 Mischpult ausgebaut Aus dem Handbuch:1x Input channel (like 9 to 16) These are balanced phone jack connectors. The nominal input level is –60 dB to +4 dB. Wiring is sleeve–ground, tip–hot (+), and ring–cold (–). They can be used with balanced or unbalanced plugs. Alles wie auf den Bildern zu sehen ! Angebotsinhalt / siehe Bilder gebraucht guter Zustand Versand erfolgt ausschließlich als versichertes Paket ! trotz allem gilt folgendes: Privatverkauf unter Ausschluss jeglicher Garantie / gesetzlicher Gewährleistung Keine Rücknahme. Mit Abgabe eines Gebotes erklärt sich der Bieter mit diesen Bedingungen einverstanden.

Enhance your audio experience with this Yamaha powered subwoofer. With a RMS power of 70 watts and impedance of 8 ohms, it delivers powerful bass that will elevate your music or movie soundtracks. The subwoofer is designed in a sleek silver cube shape, made of durable plastic material, and measures 12 inches in length and width and 14 inches in height. It is compatible with a universal range of brands, including Yamaha, and has a driver size of 8 inches. Featuring a wired connectivity option with RCA audio inputs, this subwoofer comes with a system configuration of 1 + subwoofer, allowing you to adjust the volume according to your preferences. Get ready to take your entertainment to the next level with this Yamaha YST-SW030 model subwoofer.

Yamaha JB-0029 Kopfhörer Made in Japan Rar. Mono Super ! Yamaha JB-0029 Headphones Mono Super Rar . Super Sound !

ONLY EU SHIPPING !!!! Yamaha JB-0029 Headphones Mono LUXEMBOURG : 7 EURNL : 10 EURFRANCE : 10 EUR (sauf DOM TOM)SPAIN : 12 EURGERMANY : 10 EURITALY : 12 EUR...ONLY EU SHIPPING !!!!

Yamaha JB-0029 Kopfhörer Made in Japan Rar. Mono Super ! Yamaha JB-0029 Headphones Mono Super Rar . Super Sound !

Yamaha JB-0029 Kopfhörer Made in Japan Rar. Mono Super ! Yamaha JB-0029 Headphones Mono Super Rar . Super Sound !