Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #13 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches.Please refer to the photo. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwMounting nut/washerPHONO cableInstruction manual (copy)(Japanese)Mounting gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

HIER IM VERKAUFT STEHT EINER TECHNICS SA-DA 10 SURROUND AV RECEIVER. ER IST VOLL FUNKTIONSTCHTIG. GUTER GEPFLEGTEN ZUSTAND. SELTEN BENUTZT. FERNBEDIENUNG BEDIENUNGSANLEITUNG DIES IST EIN PRIVATVERKAUFT DAHER KEINE GARANTIE UND KEINE RCKNAHME.

Parting with my beloved Technics SA-GX910 receiver is one of the absolute hardest decisions Ive had to make. ???? This Technics receiver has been a faithful companion since I picked it up on clearance from Sears in March 1993. With two factory original remotes (an extra one courtesy of Sears), this gem has been my pride and joy, and its time to find it a new home where it will be equally cherished. Continue reading to discover the heartfelt reasons why this receiver has been such a cherished keeper for so many years. Specifications:Power Output: 125 watts per channel into 8? (stereo)Surround Output: 125W (front), 60W (center), 30W (rear)Frequency Response: 7Hz to 70kHzTotal Harmonic Distortion: 0.008%Damping Factor: 30Input Sensitivity: 3mV (MM), 200mV (line)Signal to Noise Ratio: 80dB (MM), 90dB (line)Speaker Load Impedance: 4? to 16?Digital Inputs: OpticalVideo Connections: Composite, SVHS A Personal Journey This receiver is not just an electronic device, it’s a piece of my history. From rocking the house during countless gatherings and parties to delivering perfect theater sound during quiet evenings, this receiver has been a centerpiece of my audio setup. Its been well-maintained and serviced by authorized technicians to ensure it remains in top-notch condition. I remember when I drooled over this model once Sears introduced it back in late 1991 and how I was amazed that a Technics receiver actually sounded this incredibly good, especially compared to many Pioneer, Kenwood, Marantz, Sherwood, & JVC branded receivers as well as the previous generation Technics receivers. Oh, the excitement of when it went on clearance, buying it with whatever money I had left in my checking account, rushing home, really struggling to haul the heavy beast up a couple flight of stairs on my own a step at a time to my apartment back then, and anxiously unboxing it, experiencing the thrill of setting it up, and the joy of experiencing its astounding sound quality with amazement. It was wonderful being the envy of many music lovers with this receiver back then. This was one of the last known powerhouse receivers that did not require a separate subwoofer to shake the walls, provided you had good high power handling front speakers. Why Its Special This Technics SA-GX910 is one of the last true Monster Powerhouse Receivers of its era. This gem is crafted with the finest components by Technics/Panasonic, delivering sound quality that rivals most Technics separate components. I know because I am an audiophile and I conducted many in store comparison tests back in Sears. I kind of now feel sorry for the salesperson I worked with. Lol Heres a taste of what makes this receiver extraordinary:Built-in MASH DAC with Optical Input: Perfect for your CD or DAT player, and compatible with certain modern sound cards (not all) with SPDIF out, up to 48kHz. Imagine the pristine audio quality this brings to your setup!Superior DSP/Surround Sound Processor: It outperforms even Onkyos legendary Motorola DSP from the 90s. Experience surround sound like never before with high output rear channels—something other receivers couldnt match back then.Vintage Rotary Tuning Knob: Smooth, weighted, and reminiscent of classic 70s analog receivers. Feel the nostalgia with every turn.True Metal Faceplate and Rugged Chassis: Unlike its 90s counterparts, this receiver boasts a solid metal faceplate and a thick steel chassis. Its built to last and feels substantial, with a weight that speaks to its quality. The only plastic items are the center display and buttons. The volume knob has a metal outer casting, and the tuning knob is solid aluminum. And theres more:Massive Power Transformer: This beast is heavy for a reason—its powerful transformer ensures robust, solid, and stable performance.4-Band Parametric Equalizer: Customize your sound with precision. Whether youre tweaking bass and treble or diving into detailed parametric adjustments, this receiver offers a lot of control for your sound. It even has 4 presets for you to save your hours of finely tuned EQ settings. This is perfect for saving your EQ night settings when you dont want to disturb others and its time to tone it down. Crank it up and youll quickly realize why you are definitely going to need more powerful front speakers—this receivers bass output is not for the faint of heart if thats your thing. Dont say I didnt warn you!! Made in Japan with meticulous attention to detail, the Technics SA-GX910 is more than just a receiver, its a testament to the golden age of audio equipment. Amplifier Excellence The SA-GX910 is equipped with one of the best New Class A amplifiers featuring the famed Synchro Bias, popular in many Technics amplifiers, from receivers to separate power amplifiers since 1983. This amplifier technology offers superior sound quality compared to the rather hollow sounding Class H+ amplifiers that were introduced shortly after, once Technics began cost-cutting. These changes ultimately led to the brands temporary demise before its resurgence in 2016 after many hard lessons learned. Compared to newer generation Technics receivers of the 90s and early 2000s before the brands demise, the sound quality of the SA-GX910 seriously outperformed them all, even outperformed the SA-TX50, SA-AX6/7, SA-TX1010, and SA-DA20 when seeking for an upgrade. Phono Preamp Quality This receiver also boasts a very decent sounding and well-built phono preamp that stands out from others of the same period. When turntables fell out of favor, many phono preamps were no longer built with quality components or care. The Technics SA-GX910 did not compromise on its phono preamp, ensuring excellent sound for vinyl enthusiasts. Condition and Extras The condition is very decent for its age, with barely noticeable blemishes on the front faceplate and some minor scratches on the sides from being in a stereo cabinet. There is a tiny, barely noticeable dent in the rear right top corner of the case cover. All in all, the condition is rated an A-, especially for wear and tear on a receiver this vintage. It still practically looks new and grabs attention with the mesmerizing parametric EQ display. Terms and Conditions Due to the nature of electronics, this receiver is being sold as-is, although I guarantee it will not be DOA. It will be packaged very cautiously and carefully to ensure safe delivery. Shipping Cost: Due to the heavy weight and careful packaging required, the shipping cost will be on the higher side. Packaging Details: The remotes will be carefully packaged, and I will pull off the volume and tuning knobs and wrap them in a bubble wrap package along with the remotes. Why, you might ask? Well both knobs have excess protrusion, and this extra step is to better protect the front faceplate and to prevent potential shipping damage to the faceplate and internal faceplate board if the shipper is careless. I had this happen to me with a Philips receiver I purchased years ago where it was banged on the front and the impact to the volume control broke the holder nut, causing the volume board inside the receiver to be severely damaged, rendering it DOA, so I understand how these things can go. You will just need to put the volume and tuning knobs back on the receiver after unpackaging it. No screws or torx tools required. Included Items: The sale includes both remotes and the power cord. While the Pinnacle PN2+ speakers that I used for surround sound, as seen in the pics, are not included in this sale, however, if youre interested send me a message, I will send you pics of the speakers, and make a good offer. As always, dont be shy to reach out to me with any questions about this receiver. Im the only original owner of this fantastic receiver so I will be glad to answer any questions. This receiver deserves a special place for you music lovers, and I hope it brings as much joy to you as it has to me.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #12 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches.Please refer to the photo. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwMounting nut/washerPHONO cableInstruction manual (copy)(Japanese)Mounting gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

TECHNICS SA DA 10 Receiver Technics SA-DA10 AV Control Stereo Receiver with cable Specifications Tuning range: FM, MW Power output: 100 watts per channel into 6? (stereo) Surround output: 100W (front), 100W (center), 100W (rear) Frequency response: 10Hz to 70kHz Total harmonic distortion: 1% Input sensitivity: 3mV (MM), 200mV (line) Signal to noise ratio: 80dB (MM), 100dB (line) Channel separation: 55dB (line) Output: 200mV (line) Speaker load impedance: 4? to 16? Digital inputs: coaxial, optical Video Connections: composite, SVHS Dimensions: 430 x 180 x 370mm Weight: 12.7kg

This Technics SA-DA10 AV Control Stereo Receiver is a fantastic addition to any home audio setup. With its superior sound quality and advanced technology, this A/V receiver is sure to impress even the most discerning audiophile. The receiver is in great condition and has been well-maintained, ensuring that it will provide many years of reliable use. Featuring a sleek design and easy-to-use controls, this Technics SA-DA10 receiver is the perfect choice for anyone looking to take their home audio experience to the next level. Whether you're watching movies, listening to music, or gaming, this receiver delivers crisp, clear sound that will immerse you in the action. So why wait? Add this amazing receiver to your collection today and start enjoying the ultimate in home audio performance! Works great and remote works as well! Upgraded my system so no need for this anymore.

Exc cond . Works Great! No remote. This is a Mosfet Amp. it has a warmer ,some say tube like sound. USA shipping only

This sale is for:*Technics SA-DA10 Control Stereo Receiver*Technics EUR-51984 Remote Controller.*Power cordThis is a beautiful receiver, timeless design despite its modern looks. Great build quality It produces a rich detailed sound with great body and top end detail. This receiver was tested and it works great! Technics SA-DA10 PROVIDES AN EXCELLENT SOUND!Overall the unit is in GREAT used condition, shining!! The Technics Logo is missing on the left front corner, sorry! Please take a good look at the photos they are very clear and zoomable. Ask any questions, Ill be happy to answer! Please be advised - this receiver is getting hot and need good ventilation! The fan is turn ON automatically when the Volume control is rising up. All lights and indicators are working great. This Technics is looking perfect and sounds amazing! Please take a note - the Return is not accepted in this sale! I cant afford this Beautiful Unit to be drifted up and down across the country! Please be SURE you want this wonderful Technics! I guarantee it is in very good working condition! It sounds great and looks amazing!SpecificationsTuning range: FM, MWPower output: 100 watts per channel into 6? (stereo)Surround output: 100W (front), 100W (center), 100W (rear)Frequency response: 10Hz to 70kHzTotal harmonic distortion: 1%Input sensitivity: 3mV (MM), 200mV (line)Signal to noise ratio: 80dB (MM), 100dB (line)Channel separation: 55dB (line)Output: 200mV (line)Speaker load impedance: 4? to 16?Digital inputs: coaxial, opticalVideo Connections: composite, SVHSDimensions: 17 x 7 x 14 1/2Weight: 28lbAccessories: remote control Thanks for visiting my sale page! Please see my other Vintage Audio/Video gears for sale!

Exc cond . Works Great! No remote. This is a Mosfet Amp. it has a warmer ,some say tube like sound. USA shipping only

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #11 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.There is some tarnish on the arm base.Other appearance is a beautiful product without any noticeable scratches. Please refer to the photo. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwMounting nut/washerPHONO cableInstruction Manual (copy) (Japanese)Mounting gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Originally supplied with audio/video receiver model: Technics SA-DA10Model: EUR51984Part Number: EUR51984Catalogue No.: 22512Battery Required : AA Battery 2 pack

Exc cond . Works Great! No remote. This is a Mosfet Amp. it has a warmer ,some say tube like sound. USA shipping only

Exc cond . Works Great! No remote. This is a Mosfet Amp. it has a warmer ,some say tube like sound. USA shipping only

Exc cond . Works Great! No remote. This is a Mosfet Amp. it has a warmer ,some say tube like sound. USA shipping only