SNELL TYPE CV 3 WAY, 5 SPEAKER - 8 OHM / 40-250 WATT TOWER SPEAKERS. CONSECUTIVE SERIAL NUMBERS. THERE WAS A SMALL HOLE ON THE WOOFER THAT WAS REPAIRED AS CAN BE SEEN IN THE PICTURES, BUT HAS NO AFFECT ON THE OPERATION OF THE SPEAKERS. BESIDES THAT THESE SPEAKERS ARE IN VERY GOOD CONDITION AND SOUND AMAZING. THE SPEAKERS WEIGH OVER 110 LBS A PEICE. IF YOU HAVE ANY CONCERNS, PLEASE CONTACT US PRIOR TO YOUR PURCHASE. (LOCAL PICK UP ONLY)

Diese Wandhalterung scheint ein Vorläufermodel der aktuellen SoundXtra Halterung SDXDH250WM1011 zu sein. Ich hatte sie für einen Denon Home 250 im Einsatz und sie hat gut gehalten.

Vintage Hafler 9505 Transnova Power Amplifier Working 250 Watt Per Channel Works Great. Tested and Working. Uses a standard three prong cable which is not included. Sold as is . Power output: 250 watts per channel into 8? (stereo), 750 watts into 8? (mono)Frequency response: 20Hz to 20kHzTotal harmonic distortion: 0.1%Damping factor: 100Gain: 29 dBInput sensitivity: 1.58VSignal to noise ratio: 100dBDimensions: 19 x 12.5 x 5.25 inchesWeight: 50lbs

FOR SALE IS A NAIM NAP 250 POWER AMPLIFIER,A NAIM NAC 32.5S WITH MC PHONO BOARDS AND A NAIM SNAPS THE NAP 250 AND NAC 32.5S COME IN THERE ORIGINAL BOXES THE NAIM 250 POWER UP AND SO DOES THE SNAPS (VERY VERY FAINT LED LIGHT) BUT THERE ARE NO CABLES OR LEADS SO THE 32.5S HAS NOT BEEN TRIED THEY ARE CHROME BUMPERS AND IN OVERALL GOOD/VERY CONDITION PLEASE SEE PHOTOS, BUT IM SELLING THESE AS SPARES OR REPAIR AS IM SURE THEY WILL NEED A SERVICE AND MAY NOT WORK ( EVEN THOUGH I WAS ASSURED THEY DID) ONLY ASKING £1450 SOMEBODY COULD GET A BARGAIN

Naim snaic cable SNAXO 24 to NAP250 Custom 2x 4pin DIN to XLR Active Crossover Basically this will convert you snaxo so that the channels can be split horizonally instead of vertically without having to mess about with getting perfect matching amps. With the cable method you can always revert back to left and right. Picture is for illustration only but I will use chord cables. I can make the snaxo 4 pins to XLR (NAP 250) or 4 pins (NAP 180). Naims intention are to have 2x 250s equal amps but they are not dual mono constructed we all know no 2 amps are the same which is why we want to split them vertically to get it working symmetrically otherwise you an uneven left and right sounding system. For a fully active system that cost nearly 10k that is a major correction.Typical setup.Linn LP12Naim NAC 52 preampNaim SupercapNaim Snaxo 24 <----Naim Hicap2x Naim 250 NAPNaim SBL SpeakersI can also make it so that you can use the NAP 250 for the lower end and the NAP180 for the top end. Happy to post or collection is available.

Naim 4-Pin to XLR SNAIC Genuine. Good used condition. RRP 199 new! Genuine authentic Black NAIM interconnect 4pin din to XLR Designed to connect Naim preamp to power Naim 250 amplifier Compatible with: Power Amplifiers: NAP 250 Length 1.2m

Naim snaic cable SNAXO 24 to NAP250 Custom 2x 4pin DIN to XLR Active Crossover Basically this will convert you snaxo so that the channels can be split horizonally instead of vertically without having to mess about with getting perfect matching amps. With the cable method you can always revert back to left and right. Picture is for illustration only but I will use chord cables. I can make the snaxo 4 pins to XLR (NAP 250) or 4 pins (NAP 180). Naims intention are to have 2x 250s equal amps but they are not dual mono constructed we all know no 2 amps are the same which is why we want to split them vertically to get it working symmetrically otherwise you an uneven left and right sounding system. For a fully active system that cost nearly 10k that is a major correction.Typical setup.Linn LP12Naim NAC 52 preampNaim SupercapNaim Snaxo 24 <----Naim Hicap2x Naim 250 NAPNaim SBL SpeakersI can also make it so that you can use the NAP 250 for the lower end and the NAP180 for the top end. Happy to post or collection is available.

Naim snaic cable SNAXO 24 to NAP250 Custom 2x 4pin DIN to XLR Active Crossover Basically this will convert you snaxo so that the channels can be split horizonally instead of vertically without having to mess about with getting perfect matching amps. With the cable method you can always revert back to left and right. Picture is for illustration only but I will use chord cables. I can make the snaxo 4 pins to XLR (NAP 250) or 4 pins (NAP 180). Naims intention are to have 2x 250s equal amps but they are not dual mono constructed we all know no 2 amps are the same which is why we want to split them vertically to get it working symmetrically otherwise you an uneven left and right sounding system. For a fully active system that cost nearly 10k that is a major correction.Typical setup.Linn LP12Naim NAC 52 preampNaim SupercapNaim Snaxo 24 <----Naim Hicap2x Naim 250 NAPNaim SBL SpeakersI can also make it so that you can use the NAP 250 for the lower end and the NAP180 for the top end. Happy to post or collection is available.