This is an early (Two piece main weight) SME 3009 series 2 Not improved arm with a very low 4 digit serial number 2746 *The little plastic clip that holds down the arm is broken - it still sits flat on the stand but would fall if moved - I have ordered an NOS complete clip -and will include this This does not include the head shell. Everything else is there including new rubber plate mounts, I will pack this up perfectly and ship insured to the USA by UPS 2nd Day. International sales are through eBay global shipping. It does not get better than this for that meticulous 1960s turntable restoration. Its hard to know what to ask for something like this that is so very rare in this condition This tonearm was meticulously rebuilt and modified by SMETONEARMS.com years ago and not been installed since. This is a description of the SMETONEARMS processes that can also be found on their website - SME arm it is completely broken down to its most basic of components.- All parts are checked for acceptable tolerances.- All parts are put through a two stage acid bath and then sent through our sonic cleaners.- Unacceptable parts are discarded & replaced with New Old Stock SME British-made parts.- All external components are refinished to their brilliant original factory finish, shine & luster.- The two sets of pillar bearings are extracted and sonically cleaned.- We can also upgrade the pillar bearings to ABEC 9 Ceramic Roller Bearings from SKF in France for a nominal fee of $35.00 per bearing. Once this process is completed the re-wiring can begin - - We install a double continuous uninterrupted 1.25 meter run of one of the finest Cardas tonearm cables in the world. - The 4 X 33 Awg Cardas fully shielded Litz Wire - Highly shielded through a myriad of shielding processes to safeguard against outside RF interference. - Thanks to its Litz coating & Golden Section Stranding Conductors it is also one of the most musical tonearm wires in the world. - Once the arm has been wired it is then terminated at the end of the 1.25 meter run with Neutrik RCA connectors or Neutrik XLR connectors employing a superb strain relief system. - We have found these Neutrik connectors to be superior connectors due to the employment of this superb strain relief system.

This is an early (Two piece main weight) SME 3009 series 2 Not improved arm with a very low 4 digit serial number 2746 *The little plastic clip that holds down the arm is broken the piece is included - it still sits fin on the stand but would fall if moved - I have ordered an NOS complete clip -and will include this This does not include the head shell. Everything else is there including new rubber plate mounts, I will pack this up perfectly and ship insured to the USA by UPS 2nd Day. International sales are through eBay global shipping. It does not get better than this for that meticulous 1960s turntable restoration. Its hard to know what to ask for something like this that is so very rare in this condition This tonearm was meticulously rebuilt and modified by SMETONEARMS.com years ago and not been installed since. This is a description of the SMETONEARMS processes that can also be found on their website - SME arm it is completely broken down to its most basic of components.- All parts are checked for acceptable tolerances.- All parts are put through a two stage acid bath and then sent through our sonic cleaners.- Unacceptable parts are discarded & replaced with New Old Stock SME British-made parts.- All external components are refinished to their brilliant original factory finish, shine & luster.- The two sets of pillar bearings are extracted and sonically cleaned.- We can also upgrade the pillar bearings to ABEC 9 Ceramic Roller Bearings from SKF in France for a nominal fee of $35.00 per bearing. Once this process is completed the re-wiring can begin - - We install a double continuous uninterrupted 1.25 meter run of one of the finest Cardas tonearm cables in the world. - The 4 X 33 Awg Cardas fully shielded Litz Wire - Highly shielded through a myriad of shielding processes to safeguard against outside RF interference. - Thanks to its Litz coating & Golden Section Stranding Conductors it is also one of the most musical tonearm wires in the world. - Once the arm has been wired it is then terminated at the end of the 1.25 meter run with Neutrik RCA connectors or Neutrik XLR connectors employing a superb strain relief system. - We have found these Neutrik connectors to be superior connectors due to the employment of this superb strain relief system.

We use a 24 hour courier service but please allow up to 3 days handling time as a lot of our items are large and timeconsuming to package. Many thanks :) Description: Here we have an SME 3012 12” vintage tonearm It has some later parts form a series III and an RCA conversion. The headshell is an Ortofon SPU type (has a few soldering iron marks on the underside) onw of the wires has coen adrift on the output, near the RCA plugs and the headshell collar has seized on the wand, ad will need freeing. It will also need a further detailed clean.sold for light restoration. a few light marks on the wand. Please inspect the pictures (please also use the zoom function on the photos) and be sure of what you are buying, please don’t buy this if you are at all unsure, I will answer any questions you have, just email BEFORE PURCHASING. This is a used item and has been fairly described to the best of our ability. If you are not happy with any item, we can arrange collection from you for a full refund (even if you are outside the UK) We will not provide any partial refunds and will not cover any restoration, detailed or internal cleaning, repairs or modification costs. Any questions regarding out of eBay deals or part ex will be ignored as this is not allowed under ebay listing rules. Any items suspected missing in transit, must be reported to us within 10 days. We take payments through the ebay managed payments system. Shipping We ship using a 24 hour courier. Please allow up to 3 days handling time as a lot of our items are large and take time to package well. Collections We take payments through the ebay managed payments system. Visit our store!Hi-Fi Hangar Vintage hifi specialists Other PROJECTS, SPARES & REPAIRS HI-FI & AUDIO EQUIPMENT AMPLIFIERS DISK PLAYERS (CD/DVD/MD/SACD) TUNERS CASSETTE/TAPE DECKS SPEAKERS STUDIO EQUIPMENT TURNTABLES/RECORD PLAYERS CARTRIDGES TONEARMS MERCHANDISE T-SHIRTS ACCESSORIES Payment We take payments through the ebay managed payment system Shipping We ship using a 24 hour courier. Please allow up to 3 days handling time as a lot of our items are large and take time to package well. _gsrx_vers_1545 (GS 9.4.1 (1545))

Garrard 301 Turntable - SME 3009 S2 improved arm and Shure V15 iii cart FULLY RESTORED. This is absolutely immaculate and is ready for another 60 years service. The turntable was originally built in April 1964. I will ship fully insured but I would prefer collection so you can satisfy yourself and buy with confidence. Although the details state shipping insurance is set at £500, I will pay extra to have it insured for the full purchase price. As plinths are very personal this is a basic design using a solid oak top and frame, biscuit used on all four mitres and 4 semi hemisphere sorbothane supports. Linn Sondek style feet. The 301 turntable was recently fully serviced by Ray Clarke at Classic Turntable Company Limited (April 2023) Ray is considered the best in his field and his work is highly regarded. https://www.classichifi-shop.co.uk The SME 3009 series 2 improved arm was completely restored by Audio Oregami (April 2023) http://www.audioorigami.co.uk/tone-arm-rewires/ The arm comes with a Shure V15 mkiii and has a brand new Jico VN35HE stylus installed with less than 1 hour of use for testing. Turntable service details: Strip and remove all parts Clean polish Chassis Shot Blast Chassis Powder Coat Chassis Acid remove Cadmium off linkage and replate with zinc pasivated gold Replace rubber grommets Strip Spindle Check wear and replace bushes Ultrasonic clean spindle re oil and rebuild Strip motor – Re place oil felts and re oil & assemble Replace Suppressor Replace any broken / cracked plastic components Check idler wheel bushes and replace if needed Re condition idler wheel or replace if worn Use new / replated screws for assembly Fit new motor springs Replace motor spring dampers Polish eddy brake disc Fit new Idler wheel springs Refit newly plated linkage / grease/ reset Replace motor clamp Adjust motor pulley size to get speed central on speed control Fit a new mains cable with soldered ends and insulate sleeves Re-cut platter strobe. Tone arm full restoration included full rewire plus external cable upgrade with the super ofc cable and modified gold neutrix phonos and sep. earth lead.

Genuine SME replacement part for the classic tonearm. postage discount given for multiple items.

DESCRIPTION: 100% original SME Factory Made 3009 or 3012 metal clasp arm rest *** Shipping: Any item sold with a value in excess of £10 will be shipped with a minimum of a signature requirement upon delivery. The actual cost of shipping is charged we do not profit in any way from shipping costs IMPORTANT INFORMATION PLEASE READ: Buyers with less than 10 positive feedbacks, 96% positive feedback or private feedback ratings should email me prior to committing to bid / buy Any item sold with a value of £40+ must be shipped with insurance Payment via Pay Pal must be received within 48 hrs of purchase Your item will be dispatched as soon as payment is received Via Pay pal in £GBP ****THANK YOU FOR VISITING SIGNIFICANTSOUND****

SME Shure 3012 Tone Arm acquired from the estate of an audiophile. This tone arm and its required weights, etc. were packed away in a box. Original cable with multiplug and RCA plugs/ground is included. I noticed that the back part of the tone arm which holds the weight and is attached by a piece of rubber is starting to disintegrate. So, the back of the tone arm that holds the weight feels a little loose due to the weak rubber connection. Thats the best way I can explain this flaw. The small weight attached by monofilament is present along with the spring holder, and the other double weight. I know less than Nothing about this tone arm so please base your bid on the included auction photos. Again, I dont know if this unit is working, complete, etc. Offered for Restoration/Parts and sold as is. What you see is Exactly what you get. NO UNPLEASANT SURPRISES. Shipping includes packing/handling/and insurance. US SALES ONLY, (Ships to the 48 US Mainland States.) PAYMENT OPTIONS: All Ebay accepted payment methods including PayPal . For items valued at $100.00 or more there is SIGNATURE REQUIRED at the door upon delivery. We will only ship to the address listed on Ebay. All merchandise is sold as is. There are no refunds, and all sales are final. That is to protect us from the few dishonest Ebayers who play switch and blame, parts pirates, etc. We state the condition of the item to the best of our ability. Since most of the equipment we sell is vintage or preowned, there are no warrantees or guarantees on any of the items we sell. Look through our past auctions, we tell it the way it is. If you have any questions feel free to email us about the auction youre interested in. We will respond as quickly as possible. We use FedEx exclusively for shipping. Most items are hand packed in house. We pack each item differently depending on size, weight, shape, etc. Your item will be packed as if we were sending it to ourselves. You will not be disappointed with our packing skills. We use Kinkos FedEx or a private packing service for excessively large and heavy items. We include insurance free of charge on all of the items that we sell. We will only ship to a legitimate street address. FedEx does not ship to P.O. boxes. WE ONLY SHIP WITHIN THE CONTINENTAL USA (48 States.) Your item will be shipped within 1 - 5 business days after receiving payment. A confirmation email will be sent when your item has been shipped. Fedex ground takes anywhere from 2-8 working days for delivery, depending on your location in relation to ours. Please have patience. As previously stated, I send out a confirmation email the day your item is shipped. We have no control over FedEx. I promise you, it will get there! All items are cleaned and disinfected on the exterior before photos are taken and again before shipment unless stated in my auction. You wont receive any dirty, smelly, smoke stained items from this seller. We do not open up working units to inspect or to clean. Under no circumstances will an auction be terminated early, it is unfair to my fellow Ebayers and to the seller. We are no longer accepting bids from 0 FeedBack members or bidders. By bidding on this auction you are agreeing to the conditions stated above. Thank you for your understanding and good luck.

Up for sale is an SME FD200 box plus accessories suitable for the 3009 & 3012 series tonearms. Please note that the damper tank is NOT included nor available. This box and its contents are presented as recently found after decades of storage. The box is in near mint condition and truly exceptional for its age. Included inside is - - Assorted fixings - Right opening arm rest for 3009/ 3012 & R-series - Control lever for 3009 - Series II unimproved control lever - FD-2014 cartridge seating compound. This is not guaranteed to be useable due to it being a ?40 year old compound, but it is soft and malleable. Will be sent very well packed via Royal Mail 1st Class Recorded. UK sale only. Thank you for taking and interest in this item!

Tonearm SME 3012 for part or restore The tube is bent For sale like the picture Armboard include No return Shipping international with tracking