1x Silver Version Gently Used, One Small Scratch Above Main Knob, In Great Condition otherwise. This amp is better than or as good as amps from Topping, Violectric, IFI,Burson, Schiit, Monolith, Fiio, Chord, RME, SMSL, Atom, Earman, and Ferrum amplifiers. The Strong, Silent Type Asgard 3 is a highly powerful, highly affordable, modular headphone amp and preamp that gives you a complete, single-box solution for all your desktop needs. It’s a re-thinking of the headphone amp that started it all (for Schiit, anyway—the original Asgard, introduced in June 2010, was our first product.) Asgard 3 features our unique Continuity™ topology that extends the benefits of Class A output, and accepts all the same modules as Jotunheim and Lyr 3. Asgard 3’s all-new Continuity output stage delivers 3.5W into 32 ohms—a whopping 3.5X more than any previous Asgard—while also running 500mW of Class A bias. What this means is you have tons of power for virtually any headphone—and, since full power is delivered to the ¼” jack, you don’t need balanced headphone cables to take advantage of it. At the same time, Asgard 3’s low noise floor means you are ready for the most sensitive IEMs. A Complete Desktop Control Center Select from the internal card or rear-panel analog input, and pick high or low gain with convenient front switches. Connect the preamp output to your powered monitors for a complete desktop system—or use it as a front end to your speaker power amplifier. Asgard 3 provides all the flexibility you need. Designed and Built in California By “designed and built in California this is what we mean: the vast majority of the total production cost of Asgard 3—chassis, boards, transformers, assembly, etc—goes to US companies manufacturing in the US. Our chassis are made minutes from our facility. Our PCBs are done just over the hill from us, or done in NorCal. Our transformers are also made in California. You get the picture. Frequency Response: 20Hz-20Khz, -0.1db, 2Hz-400KHz, -3dB Maximum Power, 16 ohms: 5W RMS per channel Maximum Power, 32 ohms: 3.5W RMS per channel Maximum Power, 50 ohms: 2.5W RMS per channel Maximum Power, 300 ohms: 600mW RMS per channel Maximum Power, 600 ohms: 300mW RMS per channel THD: Less than 0.002%, 20Hz-20KHz, at 1V RMS, high gain mode (worst case) IMD: Less than 0.002%, CCIF at 1V RMS, high gain mode (worst case) SNR: More than 115db, unweighted, referenced to 1V RMS, in low gain mode Crosstalk: Less than -82dB, 20Hz-20KHz, 300 ohm load Output Impedance: Less than 0.2 ohms in high or low gain mode Input Impedance: 22K ohms Gain: High = 6 (15.6dB) or Low = 1 (0dB), via rear switch Topology: Fully discrete, current feedback with Continuity™ constant-transconductance output stage and stacked power supply rails Protection: Standard muting relay for delayed turn-on and fast turn-off Power Supply: Internal 48VA power transformer with 4 separate power supply rails and over 20,000uf of filter capacitance Power Consumption: 30W Size: 9 x 6 x 2 Weight: 5 lbs

This auction is for a Schiit Asgard 3 Headphone Class A amp. Excellent working condition. No issues. Please see photos for details. Thanks for looking!

Class A Amp and Preamp Fits good in a stack. This is the latest revision of the Asgard, the Asgard 3. This also has the most expensive DAC option, the Multi-Bit DAC. Item externally has some scuffs, but internally is essentially factory new. Old stock from the warehouse, comes with no box, but does come with its original power cable.

Schiit Asgard 3 Class A Headphone Amp With DAC Module This Schiit Asgard 3 is in excellent like new condition! It includes the integrated ESS9028 DAC module with Schiit Unison USB-C. Also includes the power cable. Thanks for looking!

For sale is a used Schiit Audio Asgard 3 headphone amplifier in silver finish. It is in mint condition with no damage or scratches. All functions work. No DAC module is included. It is the 115 VAC version. Included is the Asgard 3, original packaging, USA power cord, manual and a pair of PYST Snake Oil 6 RCA cables. Free shipping to any US address. No returns.

Schiit Asgard 3 Modular Headphone Amp & Preamp. In excellent working condition. Comes with manual and power cord.

For sale is a used Schiit Audio Asgard 3 headphone amplifier in silver finish. It is in mint condition with no damage or scratches. All functions work. No DAC module is included. It is the 115 VAC version. Included is the Asgard 3, original packaging, USA power cord, manual and a pair of PYST Snake Oil 6 RCA cables. Free shipping to any US address. No returns.

Everything is in perfect working order. Comes with all the cables and cords. This set up costed me around $2000 when new.

I Got some new equipment in so Im trying to sell the old stuff! This is a Schiit stack featuring the Asgard 3 (Amp) and Modius (DAC), both are in pristine condition since all they really did was sit my shelf through out the years. I have the original box and cables, however, the Modius power cable crapped out on me so I replaced it with a more robust one. Im also including some RCAs and a long type C to micro cable! Please look up reviews for these two units before buying to see if its right for you! Reviews by WaveTheory: [Asgard 3]https://www.youtube.com/watch?v=3HsoR1oK78M [Modius]https://www.youtube.com/watch?v=00hvK8hez_4&t=71s

Everything is in perfect working order. Comes with all the cables and cords. This set up costed me around $2000 when new.

Schiit Asgard 3 Headphone AMP with Built in ES9028 DAC!

Silver Schiit Asgard 3 in excellent condition. Selling because I am downsizing my collection. Only power cord included.

Introducing the Schiit Asgard 3 Headphone Amp/Preamp/Silver, a high-quality audio device designed to enhance your music listening experience. This preamp features stereo L/R RCA audio inputs and outputs, with 2 channels and 2 inputs, and is made in the United States. The amplifier class is A, ensuring a clear and powerful sound. This Schiit Asgard 3 is perfect for those who want to elevate their home audio system. Its a versatile device that can be used as a preamp or headphone amp, making it a great addition to any setup. With its sleek silver design, this preamp is not only functional but also stylish. Get ready to enjoy a superior sound quality with the Schiit Asgard 3.

Purchased 7 months ago from Schiit. Incredible dynamics micro and macro....however...Im more partial toward my Schiit Lyr 3I like a tubier sound. Hard to make decision. But some Schitt has to go.Power cord included. So far cant locate original boxLike new..and barely used No scratches and no damage...unlike other Schitt Asgards on ebay

For sale is a Schiit Stack - Asgard 3, Modius. Everything works and is in great condition. Comes with power cords. Shipping to the lower 48 only.

1x Silver Version Gently Used, One Small Scratch Above Main Knob, In Great Condition otherwise. The Strong, Silent Type Asgard 3 is a highly powerful, highly affordable, modular headphone amp and preamp that gives you a complete, single-box solution for all your desktop needs. It’s a re-thinking of the headphone amp that started it all (for Schiit, anyway—the original Asgard, introduced in June 2010, was our first product.) Asgard 3 features our unique Continuity™ topology that extends the benefits of Class A output, and accepts all the same modules as Jotunheim and Lyr 3. Asgard 3’s all-new Continuity output stage delivers 3.5W into 32 ohms—a whopping 3.5X more than any previous Asgard—while also running 500mW of Class A bias. What this means is you have tons of power for virtually any headphone—and, since full power is delivered to the ¼” jack, you don’t need balanced headphone cables to take advantage of it. At the same time, Asgard 3’s low noise floor means you are ready for the most sensitive IEMs. A Complete Desktop Control Center Select from the internal card or rear-panel analog input, and pick high or low gain with convenient front switches. Connect the preamp output to your powered monitors for a complete desktop system—or use it as a front end to your speaker power amplifier. Asgard 3 provides all the flexibility you need. Designed and Built in California By “designed and built in California this is what we mean: the vast majority of the total production cost of Asgard 3—chassis, boards, transformers, assembly, etc—goes to US companies manufacturing in the US. Our chassis are made minutes from our facility. Our PCBs are done just over the hill from us, or done in NorCal. Our transformers are also made in California. You get the picture. Frequency Response: 20Hz-20Khz, -0.1db, 2Hz-400KHz, -3dB Maximum Power, 16 ohms: 5W RMS per channel Maximum Power, 32 ohms: 3.5W RMS per channel Maximum Power, 50 ohms: 2.5W RMS per channel Maximum Power, 300 ohms: 600mW RMS per channel Maximum Power, 600 ohms: 300mW RMS per channel THD: Less than 0.002%, 20Hz-20KHz, at 1V RMS, high gain mode (worst case) IMD: Less than 0.002%, CCIF at 1V RMS, high gain mode (worst case) SNR: More than 115db, unweighted, referenced to 1V RMS, in low gain mode Crosstalk: Less than -82dB, 20Hz-20KHz, 300 ohm load Output Impedance: Less than 0.2 ohms in high or low gain mode Input Impedance: 22K ohms Gain: High = 6 (15.6dB) or Low = 1 (0dB), via rear switch Topology: Fully discrete, current feedback with Continuity™ constant-transconductance output stage and stacked power supply rails Protection: Standard muting relay for delayed turn-on and fast turn-off Power Supply: Internal 48VA power transformer with 4 separate power supply rails and over 20,000uf of filter capacitance Power Consumption: 30W Size: 9 x 6 x 2 Weight: 5 lbs

Zum Verkauf steht mein Schiit Asgard 3 mit dual AK 4490 DAC, der Verstärker wurde die letzten Jahre von mir benutzt, wird jetzt aber aufgrund eines Umstiegs auf ein Class D Verstärker verkauft.Der Verstärker funktioniert Tadellos, jedoch hat das DAC ein kleines Problem, wenn kein USB Kabel verbunden ist, gibt es ein Hochfrequentes piepen über den Kopfhöreranschluss aus, dieses verschwindet sofort, sobald ein der Verstärker per USB Kabel mit dem Computer/der Audioquelle verbunden wird. Das Problem bestand schon immer, daher weiß ich nicht, ob es bei diesem DAC normal ist oder ob es sich um einen kleinen Defekt handelt.Es gibt bei Schiit direkt auch verschiedene DAC Karten, die man kaufen und einbauen kannIm reinen Verstärker Modus mit externem DAC gibt es dieses Piepen nichtDer Kopfhörerverstärker ist nun einige Jahre alt und hat dementsprechend ein paar Gebrauchspuren, welche den Bildern entnommen werden können (kleine Oberflächliche Kratzer)Neupreis knapp 480€380€ AMP100€ DAC CardFrequency Response: 20Hz-20Khz, -0.1db, 2Hz-400KHz, -3dBMaximum Power, 16 ohms: 5W RMS per channelMaximum Power, 32 ohms: 3.5W RMS per channelMaximum Power, 50 ohms: 2.5W RMS per channelMaximum Power, 300 ohms: 600mW RMS per channelMaximum Power, 600 ohms: 300mW RMS per channelTHD: Less than 0.002%, 20Hz-20KHz, at 1V RMS, high gain mode (worst case)IMD: Less than 0.002%, CCIF at 1V RMS, high gain mode (worst case)SNR: More than 115db, unweighted, referenced to 1V RMS, in low gain modeCrosstalk: Less than -82dB, 20Hz-20KHz, 300 ohm loadOutput Impedance: Less than 0.2 ohms in high or low gain modeInput Impedance: 22K ohmsGain: High = 6 (15.6dB) or Low = 1 (0dB), via rear switchTopology: Fully discrete, current feedback with Continuity™ constant-transconductance output stage and stacked power supply railsProtection: Standard muting relay for delayed turn-on and fast turn-offPower Supply: Internal 48VA power transformer with 4 separate power supply rails and over 20,000uf of filter capacitancePower Consumption: 30WPrivatverkauf, daher keine Garantie, Gewährleistung oder Rückgabe möglich.

1x Silver Version Gently Used, One Small Scratch Above Main Knob, In Great Condition otherwise. The Strong, Silent Type Asgard 3 is a highly powerful, highly affordable, modular headphone amp and preamp that gives you a complete, single-box solution for all your desktop needs. It’s a re-thinking of the headphone amp that started it all (for Schiit, anyway—the original Asgard, introduced in June 2010, was our first product.) Asgard 3 features our unique Continuity™ topology that extends the benefits of Class A output, and accepts all the same modules as Jotunheim and Lyr 3. Asgard 3’s all-new Continuity output stage delivers 3.5W into 32 ohms—a whopping 3.5X more than any previous Asgard—while also running 500mW of Class A bias. What this means is you have tons of power for virtually any headphone—and, since full power is delivered to the ¼” jack, you don’t need balanced headphone cables to take advantage of it. At the same time, Asgard 3’s low noise floor means you are ready for the most sensitive IEMs. A Complete Desktop Control Center Select from the internal card or rear-panel analog input, and pick high or low gain with convenient front switches. Connect the preamp output to your powered monitors for a complete desktop system—or use it as a front end to your speaker power amplifier. Asgard 3 provides all the flexibility you need. Designed and Built in California By “designed and built in California this is what we mean: the vast majority of the total production cost of Asgard 3—chassis, boards, transformers, assembly, etc—goes to US companies manufacturing in the US. Our chassis are made minutes from our facility. Our PCBs are done just over the hill from us, or done in NorCal. Our transformers are also made in California. You get the picture. Frequency Response: 20Hz-20Khz, -0.1db, 2Hz-400KHz, -3dB Maximum Power, 16 ohms: 5W RMS per channel Maximum Power, 32 ohms: 3.5W RMS per channel Maximum Power, 50 ohms: 2.5W RMS per channel Maximum Power, 300 ohms: 600mW RMS per channel Maximum Power, 600 ohms: 300mW RMS per channel THD: Less than 0.002%, 20Hz-20KHz, at 1V RMS, high gain mode (worst case) IMD: Less than 0.002%, CCIF at 1V RMS, high gain mode (worst case) SNR: More than 115db, unweighted, referenced to 1V RMS, in low gain mode Crosstalk: Less than -82dB, 20Hz-20KHz, 300 ohm load Output Impedance: Less than 0.2 ohms in high or low gain mode Input Impedance: 22K ohms Gain: High = 6 (15.6dB) or Low = 1 (0dB), via rear switch Topology: Fully discrete, current feedback with Continuity™ constant-transconductance output stage and stacked power supply rails Protection: Standard muting relay for delayed turn-on and fast turn-off Power Supply: Internal 48VA power transformer with 4 separate power supply rails and over 20,000uf of filter capacitance Power Consumption: 30W Size: 9 x 6 x 2 Weight: 5 lbs

For sale is a barely used Schiit Audio Asgard 3 headphone amp. In great condition and works great. Comes with the power cord. Shipping in the lower 48 only.

Works perfectly, power cable included

Selling Schiit Asgard 3 black variant. Comes with original packaging and power supply. Item is in mint condition with no defects. 100% functional. Selling because I upgraded.

Used Schiit Asgard 3 Headphone Amp & Preamp for sale. Everything is in good, used condition. I will only ship to a US address.

This listing is for Schiit Brand Model Number #Asgard 3 With Multibit DAC #01304505. Please refer to all photos for more details as they are the best part of the description. Photos are of the actual item that you will receive. Schiit Brand Model Number #Asgard 3 With Multibit DAC #01304505 Description Our SKU: ERCA000057000US-8STR48MA_R Item Brand: Schiit Item MPN: This listing is for Schiit Brand Model Number #Asgard 3 With Multibit DAC #01304505. Please refer to all photos for more details as they are the best part of the description. Photos are of the actual item that you will receive. Please let us know if you have any questions regarding a past or future purchase. Check out our entire store for more great products and deals!! Warranty Our inventory is purchased from various different manufacturers, retailers, and 3rd party sources. We do not represent or make any claim regarding any manufacturers warranty. We do however make every possible attempt to accurately describe the inventory we sell and stand behind it. We offer a no-questions asked 30-day return policy on everything we sell if the item is in the same condition it was sold in. If you have any issues at all with your purchase please feel free to contact us, we want to make it right!! Shipping All items are carefully packed and properly protected for shipment. We use several different carriers and choose the most economical for the item and destination based on the estimated handling and transit time. Please make every attempt possible to verify that part/product being purchased is correct for your application In the event of shipping damage, item not as expected, or any other reason to desire to return the product, please feel to contact us. At this time we do not offer internation shipping. About 8TEN Industries Since 2016, 8TEN Industries has been a leading asset recovery provider supporting national retailers, brands, and manufacturers. Our 60,000 square foot processing and distribution facility located in Cass City, Michigan has allowed us to become industry leader in turning difficult problems for manufacturers into great deals for our customers. More Items Store Contact Follow Us 8TEN Industries