From a Sansui FR3060.

From a Sansui FR3060.Full set of feet.Nice simple screw mount with rubber shock cushion.Would fit other tables with a flat bottom or simple screw hole mounting.About 1 3/4 inch diameter, 5/8 inch thick.Comes with short machine screw threads screws. For other uses, you need to supply the screws.

Good used universal headshell from a Sansui FR3060.Standard interchangeable mount. Will fit many other turntables and brands.Does not have a cartridge or screws. Depending on cartridge, the screws are different length anyway.Nice condition, includes finger lift.

Good used hinges from a Sansui FR3060.Standard interchangeable mount. Will fit many other turntables and brands.As long as the rear plinth panel will accept wood screws, the bottom can be mounted.The cover part is a metal plate that uses 2 holes (each) through the cover.The hinge is a removeable design. The cover parts slide lock into the bottom hinge part.Great for custom made plinth and cover setup.Spring loaded.

This is an Original and Physical Operating Manual Condition: This is not a photocopy nor any type of reprint. This Operating Manual may contain some small damages such as small notes made by previous technicians, small aging stains, slight bends / tear, rusty staples (since it has several years old). Shipping: All the items are water-protected by several layers of cling-film and covered by stereofoam so they dont bend or get smashed. Combined Shipping: If youd wish to buy more than 1 item and save on shipping costs, send me a quick message so we can discuss if it is possible to do so. Worldwide Shipment Available.

Vintage Headshell for SANSUI FR-3060,SR-2020,SR-4040,SR-4050,FR-3080,FR-4060,SR-3030 no stylus and sold as is

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

SANSUI FR-3060 VINTAGE TURNTABLE / Tested And Working . Condition is For parts or not working. Shipped with USPS Ground Advantage.

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Sansui FR-3060 turntable. This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *