Used but in like new condition Description from their site. The HiFimeDIY ES9023 DAC was developed by DIY (do-it-yourself) enthusiasts with the purpose of making a really good, but cheap DAC that could compete against regular commercial DAC’s costing many times as much. It uses a DAC chip from the highly regarded ESS Technology. The ES9023 chip is their simplest DAC chip which keeps many of the features of their bigger brothers at a minimal cost. Simple design with focus on the technical side You pay for the sound, not the enclosure. We use a small lightweight simple case, so that you don’t have to pay extra for a bigger, heavier and more expensive enclosure. The power supply in a sound device is very important for the sound quality. We use a high end ultra-low noise regulator (LT1763) and extra capacitors to smoothen the often noisy DC power from USB ports. The DAC can also be used together with the USB Isolator to further improve the power supply quality. The isolator will isolate the power from the PC and give a cleaner 5VDC power to the DAC. We have experienced improved clarity in soundstage and separation using this isolator together with the Hifimediy DAC’s. Works with: Mac, Windows and Linux computers, no drivers required Most newer Android devices (requires OTG adapter) Also reported to work with the Synology DS115J audio station Raspberry Pi Features Output from 3.5mm headphone connector Volume Level is controlled by the normal volume control keys on your computer (no need to use the volume control inside iTunes etc.) Normal line level output (2Vrms) when connected to amplifiers/preamps. For headphones the level decreases down to 1 Vrms for 32 ohm headphones Quality gold plated headphone connector Additional (bonus) features USB to optical converter. The 3.5mm output is a dual function plug. If you connect a 3.5mm optical cable it will send SPDIF optical signal, up to 96kHz. Can be used to connect your computer to another DAC or device that doesn’t have USB input. Highlights about Saber ES9023 DAC chip The sound goes straight out of the DAC chip to your headphones or amplifier. No capacitor (that colors the sound) is required, there is no DC voltage to remove! Normally a cap is required at the DAC output, it ads costs and reduces sound quality. Jitter Eliminator! The ES9023 utilISed patented HyperstreamTM architecture and Time Domain Jitter Eliminator. 112db DNR USB chip Savitech SA9023 Accepts 32kHz, 44.1kHz, 48khz, 88kHz and 96kHz sample rates. Many USB DAC’s use the cheaper PCM2704 usb receiver chips that can only accept up to 48kHz/16bit. Works in USB Adaptive mode, DAC async mode. or Tenor chip: (older version) USB chip TenorTE7022L Accepts 32kHz, 44.1kHz, 48khz 96kHz sample rates. Most USB DAC’s use the cheaper PCM2704 usb receiver chips that can only accept up to 48kHz/16bit. Works in USB Adaptive, DAC async mode ASIO driver: ASIO drivers can provide lower latency, and is to optional to use. Asio drivers is only recommended for advanced users, and is not required for normal audio playback. Savitech asio driver available here. Tenor Asio driver for TE7022 version can be downloaded here . Output levels Open 2.2Vrms 4.7Kohm 2.1Vrms 1.8Kohm 1.9Vrms 510ohm 1.5Vrms 330ohm 1.3Vrms 30ohm 1Vrms Note: Normally amplifier inputs are from 10K to 100K ohm. Normal headphones are from 32 ohm to 250ohm. Customer feedback – Very good value DAC!!! – Outstanding audio quality; better than my Maverick D2–for 1/5 the cost. – GREAT!!! This Little thing Sound so Big, smoth, with mutch details. Thank you – Great little DAC – Very fast delivery – highly recommended – What a great product. Listening to it right now coupled with a tube amp. – very small but does good the job – Très bon dac aux dimensions étonnement petites. – Wow – this sounds AMAZING! Very fast delivery too. EXCELLENT seller. – The DAC is fantastic. Thank You! – Excellent DAC – cheapest Saber that you will find anywhere! Model:UAE23

This HiFimeDIY UAE23 USB DAC is a great addition to any home audio setup. With its compatibility with Savitech and Sabre ES9023, it is perfect for those who want a high-quality audio experience. The DAC is in excellent working order and has been well taken care of. It will provide you with a clear and crisp sound that will enhance your listening experience. The brand ESS is known for its quality and this DAC is no exception. It is perfect for those who want to upgrade their home audio components without breaking the bank. It is easy to set up and use, and will provide you with hours of listening pleasure.

HiFimeDIY UX1 ES9023 USB DAC+SPDIF/USB converter — Open Box Item — New and mint HiFimeDIY UX1 USB DAC (Sabre ES9023) + USB to SPDIF and SPDIF to USB converter This is a very nice small DAC powered by USB bus and with many useful additional features. In addition to the normal USB digital to analog audio conversion this DAC can send a SPDIF optical input to USB. And it can send a digital audio signal from a computer via USB to the SPDIF output. Please note: It does not do SPDIF to analog! It is powered from USB and doesn’t require external power supply. It has a digital volume control which will adjust the main volume level on the computer. The DAC chip is the famous Sabre ES9023 which has advanced jitter eliminator and are used in several of our other popular dacs. The headphone output is buffered by Texas Instruments’ TPA6120 current feedback power amplifier. Analoge outputs: It has two analog outputs using 3.5mm connectors. The one on the front is buffered by a headphone amplifier (TPA6120). The output on the back is direct output from the ES9023 chip. Both are controlled by the digital volume potmeter. Line output power is 2Vrms and headphone output is 250mW to 16ohm. Headphone output impedance is 10ohm Digital output: SPDIF digital output. The USB input signal is sent out through the SPDIF output. Digital input: SPDIF digital input is sent over USB to computer. Note: The SPDIF input is not sent to analog output! Input is 48kHz 16bit max. USB input: Works without drivers on Mac, Windows and Linux computer and accepts 32, 44, 48. 88 and 96 kHz sample rates and 16/24 bit. Led lights are indicating sample rate. Specifications: •Self powered from USB •Digital volume control •USB input: 32,44,48,88,96kHz,16/24bit. Sample rate indicated by LED lights •SPDIF input: 32,44,48kHz, 16 bit. •Audiophile Sabre ES9023 USB chip •Two analog outputs: One direct from the DAC chip and one buffered by headphone amp •USB adaptive transfer mode. DAC async mode with TXC 1ps oscillator •Weight 110g •Dimensions: Width 70mm, height 25mm, depth 65mm (85mm with volume knob and screws)

HiFimeDIY UX1 ES9023 USB DAC+SPDIF/USB converter — Open Box Item — New and mint HiFimeDIY UX1 USB DAC (Sabre ES9023) + USB to SPDIF and SPDIF to USB converter This is a very nice small DAC powered by USB bus and with many useful additional features. In addition to the normal USB digital to analog audio conversion this DAC can send a SPDIF optical input to USB. And it can send a digital audio signal from a computer via USB to the SPDIF output. Please note: It does not do SPDIF to analog! It is powered from USB and doesn’t require external power supply. It has a digital volume control which will adjust the main volume level on the computer. The DAC chip is the famous Sabre ES9023 which has advanced jitter eliminator and are used in several of our other popular dacs. The headphone output is buffered by Texas Instruments’ TPA6120 current feedback power amplifier. Analoge outputs: It has two analog outputs using 3.5mm connectors. The one on the front is buffered by a headphone amplifier (TPA6120). The output on the back is direct output from the ES9023 chip. Both are controlled by the digital volume potmeter. Line output power is 2Vrms and headphone output is 250mW to 16ohm. Headphone output impedance is 10ohm Digital output: SPDIF digital output. The USB input signal is sent out through the SPDIF output. Digital input: SPDIF digital input is sent over USB to computer. Note: The SPDIF input is not sent to analog output! Input is 48kHz 16bit max. USB input: Works without drivers on Mac, Windows and Linux computer and accepts 32, 44, 48. 88 and 96 kHz sample rates and 16/24 bit. Led lights are indicating sample rate. Specifications: •Self powered from USB •Digital volume control •USB input: 32,44,48,88,96kHz,16/24bit. Sample rate indicated by LED lights •SPDIF input: 32,44,48kHz, 16 bit. •Audiophile Sabre ES9023 USB chip •Two analog outputs: One direct from the DAC chip and one buffered by headphone amp •USB adaptive transfer mode. DAC async mode with TXC 1ps oscillator •Weight 110g •Dimensions: Width 70mm, height 25mm, depth 65mm (85mm with volume knob and screws)

HiFimeDIY UX1 ES9023 USB DAC+SPDIF/USB converter — Open Box Item — New and mint HiFimeDIY UX1 USB DAC (Sabre ES9023) + USB to SPDIF and SPDIF to USB converter This is a very nice small DAC powered by USB bus and with many useful additional features. In addition to the normal USB digital to analog audio conversion this DAC can send a SPDIF optical input to USB. And it can send a digital audio signal from a computer via USB to the SPDIF output. Please note: It does not do SPDIF to analog! It is powered from USB and doesn’t require external power supply. It has a digital volume control which will adjust the main volume level on the computer. The DAC chip is the famous Sabre ES9023 which has advanced jitter eliminator and are used in several of our other popular dacs. The headphone output is buffered by Texas Instruments’ TPA6120 current feedback power amplifier. Analoge outputs: It has two analog outputs using 3.5mm connectors. The one on the front is buffered by a headphone amplifier (TPA6120). The output on the back is direct output from the ES9023 chip. Both are controlled by the digital volume potmeter. Line output power is 2Vrms and headphone output is 250mW to 16ohm. Headphone output impedance is 10ohm Digital output: SPDIF digital output. The USB input signal is sent out through the SPDIF output. Digital input: SPDIF digital input is sent over USB to computer. Note: The SPDIF input is not sent to analog output! Input is 48kHz 16bit max. USB input: Works without drivers on Mac, Windows and Linux computer and accepts 32, 44, 48. 88 and 96 kHz sample rates and 16/24 bit. Led lights are indicating sample rate. Specifications: •Self powered from USB •Digital volume control •USB input: 32,44,48,88,96kHz,16/24bit. Sample rate indicated by LED lights •SPDIF input: 32,44,48kHz, 16 bit. •Audiophile Sabre ES9023 USB chip •Two analog outputs: One direct from the DAC chip and one buffered by headphone amp •USB adaptive transfer mode. DAC async mode with TXC 1ps oscillator •Weight 110g •Dimensions: Width 70mm, height 25mm, depth 65mm (85mm with volume knob and screws)

HiFimeDIY UX1 ES9023 USB DAC+SPDIF/USB converter — Open Box Item — New and mint HiFimeDIY UX1 USB DAC (Sabre ES9023) + USB to SPDIF and SPDIF to USB converter This is a very nice small DAC powered by USB bus and with many useful additional features. In addition to the normal USB digital to analog audio conversion this DAC can send a SPDIF optical input to USB. And it can send a digital audio signal from a computer via USB to the SPDIF output. Please note: It does not do SPDIF to analog! It is powered from USB and doesn’t require external power supply. It has a digital volume control which will adjust the main volume level on the computer. The DAC chip is the famous Sabre ES9023 which has advanced jitter eliminator and are used in several of our other popular dacs. The headphone output is buffered by Texas Instruments’ TPA6120 current feedback power amplifier. Analoge outputs: It has two analog outputs using 3.5mm connectors. The one on the front is buffered by a headphone amplifier (TPA6120). The output on the back is direct output from the ES9023 chip. Both are controlled by the digital volume potmeter. Line output power is 2Vrms and headphone output is 250mW to 16ohm. Headphone output impedance is 10ohm Digital output: SPDIF digital output. The USB input signal is sent out through the SPDIF output. Digital input: SPDIF digital input is sent over USB to computer. Note: The SPDIF input is not sent to analog output! Input is 48kHz 16bit max. USB input: Works without drivers on Mac, Windows and Linux computer and accepts 32, 44, 48. 88 and 96 kHz sample rates and 16/24 bit. Led lights are indicating sample rate. Specifications: •Self powered from USB •Digital volume control •USB input: 32,44,48,88,96kHz,16/24bit. Sample rate indicated by LED lights •SPDIF input: 32,44,48kHz, 16 bit. •Audiophile Sabre ES9023 USB chip •Two analog outputs: One direct from the DAC chip and one buffered by headphone amp •USB adaptive transfer mode. DAC async mode with TXC 1ps oscillator •Weight 110g •Dimensions: Width 70mm, height 25mm, depth 65mm (85mm with volume knob and screws)

HiFimeDIY UX1 ES9023 USB DAC+SPDIF/USB converter — Open Box Item — New and mint HiFimeDIY UX1 USB DAC (Sabre ES9023) + USB to SPDIF and SPDIF to USB converter This is a very nice small DAC powered by USB bus and with many useful additional features. In addition to the normal USB digital to analog audio conversion this DAC can send a SPDIF optical input to USB. And it can send a digital audio signal from a computer via USB to the SPDIF output. Please note: It does not do SPDIF to analog! It is powered from USB and doesn’t require external power supply. It has a digital volume control which will adjust the main volume level on the computer. The DAC chip is the famous Sabre ES9023 which has advanced jitter eliminator and are used in several of our other popular dacs. The headphone output is buffered by Texas Instruments’ TPA6120 current feedback power amplifier. Analoge outputs: It has two analog outputs using 3.5mm connectors. The one on the front is buffered by a headphone amplifier (TPA6120). The output on the back is direct output from the ES9023 chip. Both are controlled by the digital volume potmeter. Line output power is 2Vrms and headphone output is 250mW to 16ohm. Headphone output impedance is 10ohm Digital output: SPDIF digital output. The USB input signal is sent out through the SPDIF output. Digital input: SPDIF digital input is sent over USB to computer. Note: The SPDIF input is not sent to analog output! Input is 48kHz 16bit max. USB input: Works without drivers on Mac, Windows and Linux computer and accepts 32, 44, 48. 88 and 96 kHz sample rates and 16/24 bit. Led lights are indicating sample rate. Specifications: •Self powered from USB •Digital volume control •USB input: 32,44,48,88,96kHz,16/24bit. Sample rate indicated by LED lights •SPDIF input: 32,44,48kHz, 16 bit. •Audiophile Sabre ES9023 USB chip •Two analog outputs: One direct from the DAC chip and one buffered by headphone amp •USB adaptive transfer mode. DAC async mode with TXC 1ps oscillator •Weight 110g •Dimensions: Width 70mm, height 25mm, depth 65mm (85mm with volume knob and screws)

HiFimeDIY UX1 ES9023 USB DAC+SPDIF/USB converter — Open Box Item — New and mint HiFimeDIY UX1 USB DAC (Sabre ES9023) + USB to SPDIF and SPDIF to USB converter This is a very nice small DAC powered by USB bus and with many useful additional features. In addition to the normal USB digital to analog audio conversion this DAC can send a SPDIF optical input to USB. And it can send a digital audio signal from a computer via USB to the SPDIF output. Please note: It does not do SPDIF to analog! It is powered from USB and doesn’t require external power supply. It has a digital volume control which will adjust the main volume level on the computer. The DAC chip is the famous Sabre ES9023 which has advanced jitter eliminator and are used in several of our other popular dacs. The headphone output is buffered by Texas Instruments’ TPA6120 current feedback power amplifier. Analoge outputs: It has two analog outputs using 3.5mm connectors. The one on the front is buffered by a headphone amplifier (TPA6120). The output on the back is direct output from the ES9023 chip. Both are controlled by the digital volume potmeter. Line output power is 2Vrms and headphone output is 250mW to 16ohm. Headphone output impedance is 10ohm Digital output: SPDIF digital output. The USB input signal is sent out through the SPDIF output. Digital input: SPDIF digital input is sent over USB to computer. Note: The SPDIF input is not sent to analog output! Input is 48kHz 16bit max. USB input: Works without drivers on Mac, Windows and Linux computer and accepts 32, 44, 48. 88 and 96 kHz sample rates and 16/24 bit. Led lights are indicating sample rate. Specifications: •Self powered from USB •Digital volume control •USB input: 32,44,48,88,96kHz,16/24bit. Sample rate indicated by LED lights •SPDIF input: 32,44,48kHz, 16 bit. •Audiophile Sabre ES9023 USB chip •Two analog outputs: One direct from the DAC chip and one buffered by headphone amp •USB adaptive transfer mode. DAC async mode with TXC 1ps oscillator •Weight 110g •Dimensions: Width 70mm, height 25mm, depth 65mm (85mm with volume knob and screws)

Das Gerät ist einsatzbereit, sie müssen es nur noch ein einschalten.Installiert ist Rune Audio, es funktioniert einwandfrei. Geliefert:1x Audiophonics RaspTouch inlusive I-Sabre V3 DAC ES9023,Raspberry Pi, 7“ Touch Display, Netzteil Es gibt zahlreiche andere Softwarelösungen, die installiert werden können und all Ihre Erwartungen erfüllen: Volumio, piCorePlayer, MoOde Audio, Max2Play, RoPieee,Rune AudioRoon Ready... Je nach gewählter Software können Sie auf die folgenden Funktionen zugreifen: Volle und unbegrenzte Multiroom-UnterstützungFernwiedergabe von Audiodateien, die auf einem mit dem Netzwerk verbundenen Medienserver (NAS) gespeichert sindFernablesen von einer UPnP-QuelleLesen von einer USB-Quelle (Festplatte, USB-Stick)Verwaltung des DLNA-ProtokollsQobuz-UnterstützungAirPlay-UnterstützungRoon Bridge Ronn Ready Anschlussmöglichkeiten Der RaspTouch I-sabre 9023 V3 bietet ein einfaches und effizientes Anschlusssystem, mit dem Sie Ihr Audiosystem in vollen Zügen genießen können. So finden wir die Konnektivität des Raspberry Pi mit 4 USB-A 2.0 Ports, einem Micro SD Port, einem Ethernet Port und einem Remote HDMI Ausgang. Der analoge Audioausgang erfolgt über RCA Stereo. 7? Touch Display Der RaspTouch wird mit einem Netzteil geliefert, das an den 5,5/2,1-mm-Gleichstromanschluss auf der Rückseite des Geräts angeschlossen wird. Der Netzschalter an der Seite ermöglicht es Ihnen, das Gerät sauber auszuschalten, indem Sie das System ausschalten, bevor Sie den Strom abschalten. Der DAC Der RaspTouch basiert auf einem ESS ES9023 DAC, der die HyperStream-Architektur integriert und Abtastraten von bis zu 24bit 192kHz umsetzen kann, und bietet eine sehr gute Klangleistung. Der DAC ES9023 profitiert von fortschrittlichen Technologien und einem sorgfältigen Design, das es ihm ermöglicht, exzellente Werte wie einen Dynamikbereich von 112 dB zu erreichen. Seine hochpräzisen TCXO-Takte mit 0,5ppm und die patentierte Jitter-Reduktions-Technologie sorgen für einen besonders niedrigen Jitter-Wert. Präzisionsuhr: 0,5ppm TCXO Ultra-Low-JitterGold-überzogenen RCA-KonnektorenDC-Eingang 5,5 / 2,1 mmFull-HD-Audio – bis zu 24 Bit/192 kHz-WiedergabeDer I-Sabre V3 von Audiophonics ist ein sehr hochqualitativer DAC, der auf dem ES9023b Digital-zu-Analog Konverter Chip basiert, welcher sich bereits in der dritten Generation befindet. Der DAC wird einfach auf den Raspberry Pi aufgesteckt, somit ist kein Löten erforderlich.Dieser DAC macht vieles anders: So hat der I-Sabre einen temperaturkompensierten Oszillator mit an Board, sitzt etwas höher auf dem Raspberry Pi, so dass sich alle wichtigen Ausgänge auf der selben Seite befinden. Wie auch die DC-Buchse für den Sabre, denn der Sabre ist der erste DAC in unserem Sortiment, der eine eigene Stromzufuhr benötigt. Sobald er mit einer eigenen Stromzufuhr betrieben wird, kann er auch andere Geräte mit Strom versorgen. SPECIFICATIONS Product type Streamer Inputs 4x USB-A 1x Micro SD slot 1x RJ45 1x Stereo RCA 1x HDMI 2x 12VDC 1.25A Raspberry Pi - DAC Module Audiophonics I-Sabre V3 ES9023TCXO Screen Tactile 7 Official Raspberry Pi screen Supported sampling rate PCM up to 24bit 192kHz Dynamic range 112dB GENERAL Power supply 6V 3A via Jack DC 5.5/2.1mm (power supply) Housing material Aluminium Dimensions 200 x 95 x 230mm Rear dimensions 175 x 55mm Weight 0.9kg Color Black _gsrx_vers_1536 (GS 9.4 (1536))

Das Gerät ist einsatzbereit, sie müssen es nur noch ein einschalten.Installiert ist Rune Audio, es funktioniert einwandfrei. Geliefert:1x Audiophonics RaspTouch inlusive I-Sabre V3 DAC ES9023,Raspberry Pi, 7“ Touch Display, Netzteil Es gibt zahlreiche andere Softwarelösungen, die installiert werden können und all Ihre Erwartungen erfüllen: Volumio, piCorePlayer, MoOde Audio, Max2Play, RoPieee,Rune AudioRoon Ready... Je nach gewählter Software können Sie auf die folgenden Funktionen zugreifen: Volle und unbegrenzte Multiroom-UnterstützungFernwiedergabe von Audiodateien, die auf einem mit dem Netzwerk verbundenen Medienserver (NAS) gespeichert sindFernablesen von einer UPnP-QuelleLesen von einer USB-Quelle (Festplatte, USB-Stick)Verwaltung des DLNA-ProtokollsQobuz-UnterstützungAirPlay-UnterstützungRoon Bridge Ronn Ready Anschlussmöglichkeiten Der RaspTouch I-sabre 9023 V3 bietet ein einfaches und effizientes Anschlusssystem, mit dem Sie Ihr Audiosystem in vollen Zügen genießen können. So finden wir die Konnektivität des Raspberry Pi mit 4 USB-A 2.0 Ports, einem Micro SD Port, einem Ethernet Port und einem Remote HDMI Ausgang. Der analoge Audioausgang erfolgt über RCA Stereo. 7? Touch Display Der RaspTouch wird mit einem Netzteil geliefert, das an den 5,5/2,1-mm-Gleichstromanschluss auf der Rückseite des Geräts angeschlossen wird. Der Netzschalter an der Seite ermöglicht es Ihnen, das Gerät sauber auszuschalten, indem Sie das System ausschalten, bevor Sie den Strom abschalten. Der DAC Der RaspTouch basiert auf einem ESS ES9023 DAC, der die HyperStream-Architektur integriert und Abtastraten von bis zu 24bit 192kHz umsetzen kann, und bietet eine sehr gute Klangleistung. Der DAC ES9023 profitiert von fortschrittlichen Technologien und einem sorgfältigen Design, das es ihm ermöglicht, exzellente Werte wie einen Dynamikbereich von 112 dB zu erreichen. Seine hochpräzisen TCXO-Takte mit 0,5ppm und die patentierte Jitter-Reduktions-Technologie sorgen für einen besonders niedrigen Jitter-Wert. Präzisionsuhr: 0,5ppm TCXO Ultra-Low-JitterGold-überzogenen RCA-KonnektorenDC-Eingang 5,5 / 2,1 mmFull-HD-Audio – bis zu 24 Bit/192 kHz-WiedergabeDer I-Sabre V3 von Audiophonics ist ein sehr hochqualitativer DAC, der auf dem ES9023b Digital-zu-Analog Konverter Chip basiert, welcher sich bereits in der dritten Generation befindet. Der DAC wird einfach auf den Raspberry Pi aufgesteckt, somit ist kein Löten erforderlich.Dieser DAC macht vieles anders: So hat der I-Sabre einen temperaturkompensierten Oszillator mit an Board, sitzt etwas höher auf dem Raspberry Pi, so dass sich alle wichtigen Ausgänge auf der selben Seite befinden. Wie auch die DC-Buchse für den Sabre, denn der Sabre ist der erste DAC in unserem Sortiment, der eine eigene Stromzufuhr benötigt. Sobald er mit einer eigenen Stromzufuhr betrieben wird, kann er auch andere Geräte mit Strom versorgen. SPECIFICATIONS Product type Streamer Inputs 4x USB-A 1x Micro SD slot 1x RJ45 1x Stereo RCA 1x HDMI 2x 12VDC 1.25A Raspberry Pi - DAC Module Audiophonics I-Sabre V3 ES9023TCXO Screen Tactile 7 Official Raspberry Pi screen Supported sampling rate PCM up to 24bit 192kHz Dynamic range 112dB GENERAL Power supply 6V 3A via Jack DC 5.5/2.1mm (power supply) Housing material Aluminium Dimensions 200 x 95 x 230mm Rear dimensions 175 x 55mm Weight 0.9kg Color Black _gsrx_vers_1516 (GS 9.3 (1516))