Hello, I have for sale my Polk Audio Monitor 30 Pair of CrossoversThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Hello, I have for sale my Polk Audio Monitor 30 Pair of wooferThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Hello, I have for sale my Polk Audio Monitor 30 Pair of wooferThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio CS2 Center channel Monitor 30 Bookshelf 100W Speaker Pair - TESTED!condition is very good with very minimal marks from use/storage. tested working

You are bidding on a pair of Polk Audio Monitor 30 Speakers 100W with a Black Oak finish vinyl veneer Cabinet in very NICE condition. These speakers features Polk Dynamic Balance® drivers Including a 1 tweeter for detailed highs,and a 5-1/4 for clear, low-distortion mids and bass. Note: Take a look at my other listings, I have a matching Polk Audio CS1 Center Channel speaker up for bid and I will discount shipping if you win both auctions. Condition (see pictures): These monitors Look and sounds fantastic. The drivers are in great shape and the cabinets are very clean with no significant marks or scratches. The grill fabric on each speaker does have 1 small pull (see last 2 pics) but not terrible and still presentable. Look at the pictures and judge for yourself, these speakers are in great shape. Features: ? Manufacturer- Polk Audio ? Type- Bookshelf Speaker pair ? Model- Monitor 30 ? Consecutive Serial Numbers ? Material- Vinyl Veneer over MDF, Plastic Grill with Fabric cover ? Color- Black ? Finish- black oak vinyl finish ? Video-shielded- Yes ? Design- Bass-reflex ? Frequency Response- 63-24,000 Hz (-3dB) ? Impedance- 8 ohm ? Sensitivity- 89 dB ? Power- up to 100 watts ? Connectors- 5-way binding post terminals ? Built-in keyhole slots and rubber feet for wall-mounting ? 4 rubber feet installed on bottom Measurements (each speaker): ? Width- 7-1/16 ? Height- 11-1/16 ? Depth- 10

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio Monitor 30 SpeakersBoth speakers produce sound. BrandPolk AudioModelPolk Audio Monitor 30ConnectivityWiredColorBrownTypeBookshelf Speakers CONDITION: Used - Speakers are in good condition Terms of Sale Disclaimer: All items were donated to Goodwill of Colorado with no history or provenance. The auction is for all items pictured. Items may need servicing and/or benefit from a cleaning upon arrival. Please see photos for additional details and feel free to ask questions. Shipping Information Shipping: All items are shipped within five business days (Monday through Friday) following the date the auction was paid for. We do NOT offer any shipping options faster than FedEx Ground. All items are shipped by dimensional weight. Dimensional weight is calculated by the carrier based on the amount of cubic space an item requires for transport, and may be higher than the actual item weight. Please contact us prior to making payment if there are specific shipping requirements or requests such as signature confirmation or insurance. We do not, under any circumstances, accept pre-paid shipping labels provided by customers. Please contact us with any questions or concerns regarding shipping prior to paying.

In perfect working order, comes with speaker covers as well

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Selling a pair of Polk Audio Monitor 30 Series bookshelf speakers in black. These speakers are perfect for anyone looking for high-quality sound. They feature banana jack audio inputs and wired connectivity, making them easy to integrate into any existing audio setup. The speakers are designed for surround right and left use, making them a great choice for home theater systems. They come from the reputable brand Polk Audio and are model Monitor 30. Don't miss out on these great speakers!

You are bidding on a pair of Polk Audio Monitor 30 Speakers 100W with a Black Oak finish vinyl veneer Cabinet in very NICE condition. These speakers features Polk Dynamic Balance® drivers Including a 1 tweeter for detailed highs,and a 5-1/4 for clear, low-distortion mids and bass. Note: Take a look at my other listings, I have a matching Polk Audio CS1 Center Channel speaker up for bid and I will discount shipping if you win both auctions. Condition (see pictures): These monitors Look and sounds fantastic. The drivers are in great shape and the cabinets are very clean with no significant marks or scratches. The grill fabric on each speaker does have 1 small pull (see last 2 pics) but not terrible and still presentable. Look at the pictures and judge for yourself, these speakers are in great shape. Features: ? Manufacturer- Polk Audio ? Type- Bookshelf Speaker pair ? Model- Monitor 30 ? Consecutive Serial Numbers ? Material- Vinyl Veneer over MDF, Plastic Grill with Fabric cover ? Color- Black ? Finish- black oak vinyl finish ? Video-shielded- Yes ? Design- Bass-reflex ? Frequency Response- 63-24,000 Hz (-3dB) ? Impedance- 8 ohm ? Sensitivity- 89 dB ? Power- up to 100 watts ? Connectors- 5-way binding post terminals ? Built-in keyhole slots and rubber feet for wall-mounting ? 4 rubber feet installed on bottom Measurements (each speaker): ? Width- 7-1/16 ? Height- 11-1/16 ? Depth- 10

Hello, I have for sale my Polk Audio Monitor 30 Pair of CrossoversThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Hello, I have for sale my Polk Audio Monitor 30 Pair of wooferThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

In perfect working order, comes with speaker covers as well

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Selling a pair of Polk Audio Monitor 30 Series bookshelf speakers in black. These speakers are perfect for anyone looking for high-quality sound. They feature banana jack audio inputs and wired connectivity, making them easy to integrate into any existing audio setup. The speakers are designed for surround right and left use, making them a great choice for home theater systems. They come from the reputable brand Polk Audio and are model Monitor 30. Don't miss out on these great speakers!

In perfect working order, comes with speaker covers as well

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Selling a pair of Polk Audio Monitor 30 Series bookshelf speakers in black. These speakers are perfect for anyone looking for high-quality sound. They feature banana jack audio inputs and wired connectivity, making them easy to integrate into any existing audio setup. The speakers are designed for surround right and left use, making them a great choice for home theater systems. They come from the reputable brand Polk Audio and are model Monitor 30. Don't miss out on these great speakers!

used but in good used condition, both fully functional and sound excellent.

You are bidding on a pair of Polk Audio Monitor 30 Speakers 100W with a Black Oak finish vinyl veneer Cabinet in very NICE condition. These speakers features Polk Dynamic Balance® drivers Including a 1 tweeter for detailed highs,and a 5-1/4 for clear, low-distortion mids and bass. Note: Take a look at my other listings, I have a matching Polk Audio CS1 Center Channel speaker up for bid and I will discount shipping if you win both auctions. Condition (see pictures): These monitors Look and sounds fantastic. The drivers are in great shape and the cabinets are very clean with no significant marks or scratches. The grill fabric on each speaker does have 1 small pull (see last 2 pics) but not terrible and still presentable. Look at the pictures and judge for yourself, these speakers are in great shape. Features: ? Manufacturer- Polk Audio ? Type- Bookshelf Speaker pair ? Model- Monitor 30 ? Consecutive Serial Numbers ? Material- Vinyl Veneer over MDF, Plastic Grill with Fabric cover ? Color- Black ? Finish- black oak vinyl finish ? Video-shielded- Yes ? Design- Bass-reflex ? Frequency Response- 63-24,000 Hz (-3dB) ? Impedance- 8 ohm ? Sensitivity- 89 dB ? Power- up to 100 watts ? Connectors- 5-way binding post terminals ? Built-in keyhole slots and rubber feet for wall-mounting ? 4 rubber feet installed on bottom Measurements (each speaker): ? Width- 7-1/16 ? Height- 11-1/16 ? Depth- 10