Hello, I have for sale my Polk Audio Monitor 30 Pair of CrossoversThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio Monitor 30 Series Rosewood Bookshelf Speakers MINT CONDITION GREAT SOUND

Preowned tested working beautiful condition. Please ask questions you have. I cannot ship to a POBox and I can only ship to the 48 lower US states

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Hello, I have for sale my Polk Audio Monitor 30 Pair of CrossoversThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Hello, I have for sale my Polk Audio Monitor 30 Pair of wooferThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio Monitor 30 Series Rosewood Bookshelf Speakers MINT CONDITION GREAT SOUND

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

Polk Audio Monitor 30 Series Rosewood Bookshelf Speakers MINT CONDITION GREAT SOUND

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

7-1/16W x 11-1/16H x 10DCrisp, spacious sound at a great price. The Monitor 30 bookshelf speaker takes advantage of proven Polk technologies to deliver solid performance for your music and movies. Start with Polks celebrated Dynamic Balance® drivers — the 1 tweeter dishes out natural, detailed highs, while the 5-1/4 woofer produces clear, low-distortion mids and bass. Plus, a tuned flared port reinforces the low-frequencies without introducing sound-muddying noise. And the rock-solid MDF constuction virtually eliminates resonance. Youll enjoy clean, wide-open sound.The compact Monitor 30 will fit easily into just about any room, yet its high-efficiency design lets it produce big sound without loss of clarity. Dual 5-way binding posts allow for bi-wiring or bi-amping, and you can mount the speakers on your wall using the built-in keyhole slots. The Monitor 30 does a terrific job with stereo music, and for even better bass extension, just team it up with a powered subwoofer. Plus, you can put together a voice-matched Polk Monitor home theater speaker system for thrilling surround sound performance. Use the 30s as fronts and surrounds in a home theater setup for small-to-medium-sized rooms, or pair them up with the Polk Monitor 50 or Polk Monitor 60 towers for larger rooms

Hello, I have for sale my Polk Audio Monitor 30 Pair of wooferThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

Hello, I have for sale my Polk Audio Monitor 30 Pair of CrossoversThese are in working condition.These are in As Pictured physical condition.These will be packed with carewith protection on all sides top and bottom!The shipping is for the lower 48 states only.If you have any questions please feel free to ask, thank you!

A pair of Polk Audio MM691s. These are generally used for car audio as 6x9 replacement speakers. These have never been used. Purchased for a car long ago and have sat safely in storage for many years. The box is worn, but the components inside are unharmed. Item will be shipped in this box as is. Ill tape it well, though. From the manufacturer:Polk Audio continues its tradition of making brilliant-sounding speakers in stylishly designed packages — their Mobile Monitor (MM) Series speakers look great and sound even better. Each speaker utilizes an extra-strong, extra-small neodymium magnet that saves space and weight, allowing these speakers to fit into more places in more vehicles while still delivering a full sound with lots of kick. Their lightweight carbon composite frames provide strong, flex-free support for the speakers motor assemblies.The Polk MM691 6x9 speakers feature honeycomb-textured woven glass fiber composite woofer cones that respond very quickly for a clean, crisp, and powerful sound. Large voice coils — over an inch in diameter — give the speaker high power handling capability and extended reliability.3/4 and 1 silk dome tweeters add a sweet high end that blends perfectly with the low notes so your music stays in harmonic balance, from the electric bass all the way on up to the cymbals.Important Note: These Polk speakers use a low-impedance design to pull more power safely from your car stereo or amplifier. This design is compatible with virtually all factory and aftermarket stereos.Priced per pairREAD LESSProduct highlights:6x9 3-way speakers (pair)woven honeycomb glass fiber composite woofer cone with butyl rubber surround1 and 3/4 silk composite dome tweeterscertified for marine use2.7-ohm impedance for extra power (compatible with virtually all factory or aftermarket car stereos)power range: 15-125 watts RMS (300 watts peak power)frequency response: 30-25,000 Hzsensitivity: 94 dB @ 1 Vtop-mount depth: 3-3/16warranty: 1 year60-day returnsMFR # AA2691-AWhats in the box:Polk Audio MM691 owners manualTwo 3-way speakers2 Grilles2 Passive crossovers8 Mounting screws8 Speed clipsOwners ManualProduct Registration information sheet

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

POLK AUDIO MONITOR 30 - 1(ONE) GRILL - IN GREAT SHAPE THANKS FOR LOOKING!!

Polk Audio RM3000 Monitor Series 2 Speakers, Speckled Stone Color Used. Good condition. One speaker has a tear and there are a few small tears in the speaker covers. Speakers are very heavy. Old school quality.

A pair of Polk Audio MM691s. These are generally used for car audio as 6x9 replacement speakers. These have never been used. Purchased for a car long ago and have sat safely in storage for many years. The box is worn, but the components inside are unharmed. Item will be shipped in this box as is. Ill tape it well, though. From the manufacturer:Polk Audio continues its tradition of making brilliant-sounding speakers in stylishly designed packages — their Mobile Monitor (MM) Series speakers look great and sound even better. Each speaker utilizes an extra-strong, extra-small neodymium magnet that saves space and weight, allowing these speakers to fit into more places in more vehicles while still delivering a full sound with lots of kick. Their lightweight carbon composite frames provide strong, flex-free support for the speakers motor assemblies.The Polk MM691 6x9 speakers feature honeycomb-textured woven glass fiber composite woofer cones that respond very quickly for a clean, crisp, and powerful sound. Large voice coils — over an inch in diameter — give the speaker high power handling capability and extended reliability.3/4 and 1 silk dome tweeters add a sweet high end that blends perfectly with the low notes so your music stays in harmonic balance, from the electric bass all the way on up to the cymbals.Important Note: These Polk speakers use a low-impedance design to pull more power safely from your car stereo or amplifier. This design is compatible with virtually all factory and aftermarket stereos.Priced per pairREAD LESSProduct highlights:6x9 3-way speakers (pair)woven honeycomb glass fiber composite woofer cone with butyl rubber surround1 and 3/4 silk composite dome tweeterscertified for marine use2.7-ohm impedance for extra power (compatible with virtually all factory or aftermarket car stereos)power range: 15-125 watts RMS (300 watts peak power)frequency response: 30-25,000 Hzsensitivity: 94 dB @ 1 Vtop-mount depth: 3-3/16warranty: 1 year60-day returnsMFR # AA2691-AWhats in the box:Polk Audio MM691 owners manualTwo 3-way speakers2 Grilles2 Passive crossovers8 Mounting screws8 Speed clipsOwners ManualProduct Registration information sheet

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio RM3000 Monitor Series 2 Speakers, Speckled Stone Color Used. Good condition. One speaker has a tear and there are a few small tears in the speaker covers. Speakers are very heavy. Old school quality.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.