This listing includes the following item(s)(1) Pioneer PL-A35 Tonearm Motor Assembly Cover Condition: Excellent Condition. Minimal Wear. Well Taken Care Of. See Photos Of Actual Item. Please contact us if you have any questionsYour Satisfaction is Guaranteed 100%

This listing includes the following item(s)(1) Pioneer PL-A35 Original Power Cable Assembly Condition: Excellent Condition. Well Taken Care Of. See Photos Of Actual Item. Please contact us if you have any questionsYour Satisfaction is Guaranteed 100%

Bias (Anti skate) weight for Pioneer PL-A35 Brass version see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier brass weight used if your cartridge tracking force is set to 2.1g or higher. If your tracking force is higher than 2.1g you need the aluminum version of the bias (anti skate) weight. I have this in another listing as well as a listing for both versions of the bias weight check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Replacement set of Bias Weights (Anti skate) for the Pioneer PL-A35 contains both the aluminum and the brass weight. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This listing is for both weights if you only require one or the other I have them listed separately check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-A35 Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

This listing includes the following item(s)(1) Pioneer PL-A35 Original Power Cable Assembly Condition: Excellent Condition. Well Taken Care Of. See Photos Of Actual Item. Please contact us if you have any questionsYour Satisfaction is Guaranteed 100%

This listing includes the following item(s)(1) Pioneer PL-A35 Tonearm Motor Assembly Cover Condition: Excellent Condition. Minimal Wear. Well Taken Care Of. See Photos Of Actual Item. Please contact us if you have any questionsYour Satisfaction is Guaranteed 100%

Bias weight (Anti skate) for Pioneer PL-A35 Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Replacement set of Bias Weights (Anti skate) for the Pioneer PL-A35 contains both the aluminum and the brass weight. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This listing is for both weights if you only require one or the other I have them listed separately check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias (Anti skate) weight for Pioneer PL-A35 Brass version see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier brass weight used if your cartridge tracking force is set to 2.1g or higher. If your tracking force is higher than 2.1g you need the aluminum version of the bias (anti skate) weight. I have this in another listing as well as a listing for both versions of the bias weight check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Replacement set of Bias Weights (Anti skate) for the Pioneer PL-A35 contains both the aluminum and the brass weight. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This listing is for both weights if you only require one or the other I have them listed separately check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-A35 Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias (Anti skate) weight for Pioneer PL-A35 Brass version see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier brass weight used if your cartridge tracking force is set to 2.1g or higher. If your tracking force is higher than 2.1g you need the aluminum version of the bias (anti skate) weight. I have this in another listing as well as a listing for both versions of the bias weight check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-A35 Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Replacement set of Bias Weights (Anti skate) for the Pioneer PL-A35 contains both the aluminum and the brass weight. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This listing is for both weights if you only require one or the other I have them listed separately check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias (Anti skate) weight for Pioneer PL-A35 Brass version see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier brass weight used if your cartridge tracking force is set to 2.1g or higher. If your tracking force is higher than 2.1g you need the aluminum version of the bias (anti skate) weight. I have this in another listing as well as a listing for both versions of the bias weight check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Replacement set of Bias Weights (Anti skate) for the Pioneer PL-A35 contains both the aluminum and the brass weight. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This listing is for both weights if you only require one or the other I have them listed separately check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-A35 Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias (Anti skate) weight for Pioneer PL-A35 Brass version see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-A35 One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier brass weight used if your cartridge tracking force is set to 2.1g or higher. If your tracking force is higher than 2.1g you need the aluminum version of the bias (anti skate) weight. I have this in another listing as well as a listing for both versions of the bias weight check my other items for sale. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *