This is a Pioneer PL-12 Original Turntable Dust Cover Stereo Part in Very Good Condition. The attached top part of the hinges are included. There are no cracks, but it does have some minor marks. The center name badge says PL-12 on the outside and says Pioneer on the inside. This was removed from a model PL-12AC. This may fit other models. Please be sure it is correct for your application before purchase. It measures 16-1/8 wide x 12-1/2 deep X 2-3/4 high at the top. Across the bottom It measures 16-1/4 wide x 12-13/16. It does have a few marks which were hard to photograph. If you are expecting mint condition this is not it. It is very good condition in my opinion. See all pictures for condition. What you see is what is included. Please use the shipping calculator for USPS shipping rates. Please Email any questions. See my other auctions for other Pioneer PL-12 Turntable parts, electronics, beer signs, video games and other collectible stuff. Combine auctions to save on shipping.

Ceramic (Si3N4) is harder than steel and has better tolerance to heat and fatigue. Considered an upgrade to steel bearing.

Ceramic (Si3N4) is harder than steel and has better tolerance to heat and fatigue. Considered an upgrade to steel bearing.

Ceramic (Si3N4) is harder than steel and has better tolerance to heat and fatigue. Considered an upgrade to steel bearing.

Ceramic (Si3N4) is harder than steel and has better tolerance to heat and fatigue. Considered an upgrade to steel bearing.

Pioneer PL-12AC Belt Drive Turntable Record Player Japan VTG READ. When the record player is plugged in the switches to cause the needle to move and the motor to run respectively. I plugged in the system to a speaker and did receive sound and the motor was running smoothly but all of a sudden it slowed down and nearly stops. now the table just turns very slowly. I am no expert in record players so I do not have any additional knowledge or information.

Anti skate weight for the tonearm of the Pioneer PL-12AC turntable. ** NOTE ONLY FOR THE Pioneer PL-12AC MODEL. NO OTHER VERSION OF THE Pioneer PL12 USES THIS WEIGHT ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Pioneer PL-12AC 2-Speed Belt-Drive Turntable ~ New Belt Installed~FREE SHIPPING Click images to enlarge Description Hello.  Up for consideration is a  Pioneer PL-12AC 2-Speed Belt-Drive Turntable ~ New Belt Installed ~ FREE SHIPPING Works well and sounds good.  The cartridge is good and thebelt was just installed.  Please look at all of the photos as they are a part of the description.   FREE SHIPPING for the lower 48 states! View My Other Items For Sale Images sell! Get Supersized Images & Free Image HostingCreate your brand with Auctivas Customizable Templates. Attention Sellers - Get Templates Image Hosting, Scheduling at Auctiva.com. Track Page Views WithAuctivas Counter

Anti skate weight for the tonearm of the Pioneer PL-12AC turntable. ** NOTE ONLY FOR THE Pioneer PL-12AC MODEL. NO OTHER VERSION OF THE Pioneer PL12 USES THIS WEIGHT ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Pioneer PL-12AC turntable. ** NOTE ONLY FOR THE Pioneer PL-12AC MODEL. NO OTHER VERSION OF THE Pioneer PL12 USES THIS WEIGHT ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Pioneer PL-12AC turntable. ** NOTE ONLY FOR THE Pioneer PL-12AC MODEL. NO OTHER VERSION OF THE Pioneer PL12 USES THIS WEIGHT ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Pioneer PL-12AC turntable. ** NOTE ONLY FOR THE Pioneer PL-12AC MODEL. NO OTHER VERSION OF THE Pioneer PL12 USES THIS WEIGHT ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Anti skate weight for the tonearm of the Pioneer PL-12AC turntable. ** NOTE ONLY FOR THE Pioneer PL-12AC MODEL. NO OTHER VERSION OF THE Pioneer PL12 USES THIS WEIGHT ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *