Ortofon Headshell LH 2000 mit SME-Anschluss NEU

Ortofon 2M Red PnP MKII MM-Tonabnehmer mit integr. Headshell / SME-Bajonett. Ca. 15 Stunden gelaufen und im tadellosen Zustand. Den original Karton kann ich leider nicht finden. Das System wird gut und sicher verpackt versendet.

Ortofon M15EC Super Tonabnehmer MM auf Technics Headshell (SME Anschluss) Der Tonabnehmer ist technisch und optisch einwandfrei.Klingt hervorragend. Die originale Nadel ist im guten Zustand. Montiert auf einem Technics Headshell. Dieser Artikel unterliegt gem. § 25a UStG der Differenzbesteuerung, ein Ausweis der Mehrwertsteuer auf der Rechnung erfolgt nicht.

Ortofon M15EC Super Tonabnehmer MM auf Technics Headshell (SME Anschluss) Der Tonabnehmer ist technisch und optisch einwandfrei.Klingt hervorragend. Die originale Nadel ist im guten Zustand. Montiert auf einem Technics Headshell. Dieser Artikel unterliegt gem. § 25a UStG der Differenzbesteuerung, ein Ausweis der Mehrwertsteuer auf der Rechnung erfolgt nicht.

Ortofon 2M Red Tonabnehmer mit Nadel und Headshell SME Anschluss in gebrauchtem Zustand. Der Tonabnehmer in Rot eignet sich perfekt fr den Einsatz bei Plattenspielern und liefert einen warmen und klaren Klang. Mit dem mitgelieferten Headshell und dem SME Anschluss ist die Installation auf Ihrem Plattenspieler ein Kinderspiel. Die Nadel ist bereits installiert und in gutem Zustand. Ein muss fr jeden Vinyl-Liebhaber, der auf der Suche nach einem hochwertigen Tonabnehmer ist. Sehr wenig genutzt und ein sehr feinzeichendes System. Versand nur innerhalb Deutschlands mit DHL Paket und Sendungsnummer. Delivery only within Germany.

Ortofon M15EC Super Tonabnehmer MM auf Technics Headshell (SME Anschluss) Der Tonabnehmer ist technisch und optisch einwandfrei.Klingt hervorragend. Die originale Nadel ist im guten Zustand. Montiert auf einem Technics Headshell. Dieser Artikel unterliegt gem. § 25a UStG der Differenzbesteuerung, ein Ausweis der Mehrwertsteuer auf der Rechnung erfolgt nicht.

verkauft werden 1Stk. Ortofon Headshell Der Artikel wird so wie er ist, also gebraucht, von Privat verkauft. Dies bedeutet: mit der Abgabe eines Gebotes erklären Sie sich ausdrücklich damit einverstanden, auf die Ihnen nach neuem EU-Recht gesetzlich zustehende Gewährleistung/Garantie bei Gebrauchtwaren völlig zu verzichten. _gsrx_vers_1649 (GS 9.7.2 (1649))

verkauft werden 3 Stk. Ortofon Headshell ohne Kabel Der Artikel wird so wie er ist, also gebraucht, von Privat verkauft. Dies bedeutet: mit der Abgabe eines Gebotes erklären Sie sich ausdrücklich damit einverstanden, auf die Ihnen nach neuem EU-Recht gesetzlich zustehende Gewährleistung/Garantie bei Gebrauchtwaren völlig zu verzichten. _gsrx_vers_1646 (GS 9.7.1 (1646))

Ortofon LH 6000 Headshell Beschreibung:- SME-Anschluss - Gewicht 13,5gr. Sehr gut geeignet für MC Tonabnehmer mit geringer Nadelnachgiebigkeit. Klingt auch mit AT VM95SH sehr gut - Magnesium. Resonanzarm Zustand:- Gut. Funktioniert und klingt einwandfrei. Einige Kratzer in der Beschichtung oben. Versand als Warensendung kostenlos, oder als Paket mit Tracking e5,49. Es handelt sich hier um ein Privatangebot. Eine Gewährleistung nach EU-Recht wird ausgeschlossen

zum Verkauf steht hier einOrtofon Metall Headshell mit Bajonett-Anschluss SMEmit Kabeln + SchraubenFarbe -> schwarzDer Artikel ist ingutem Zustand - leichte KratzerDetails siehe Bilder. -------------Ich versuche durch die Bilder einen genauen Überblick über den Zustand zu geben. Ich fühle mich nicht befähigt einen Artikelzustand in Klassen anzugeben. Sehen Sie bitte in diesem Zusammenhang die Bilder an. Die verwendeten Namen und Marken dienen lediglich zur Erkennung der Artikel und sie sind Eigentum der jeweiligen Rechtsinhaber. Die angegebenen Markennamen sind geschützte Markennamen und werden hier nur verwendet, weil sie ein wesentlicher Bestandteil des Produktes sind und die Qualität kennzeichnen. Das Angebot ist von Privat und erfolgt von meiner Seite unter Ausschluss von Garantie- Gewährleistung oder Rückgaberechts-Ansprüchen! Für unversicherten Versand übernehme ich keine Gewähr. Kontaktieren Sie mich bitte, wenn Sie den Artikel versichert gesendet bekommen wollen.

einfach super

Neu aus Audio Block PS-100+ zzgl. neuem SME Headshell, ca. 1 Stunde Probegelaufen und dann wegen der Optik gegen Ortofon Red getauscht. Fertig montiert. Technische Daten: Tonabnehmer-Typ: MM (Moving-Magnet)Montage am Tonarm: Headshell mit Halb-Zoll-BefestigungAusgangsspannung: 4mV*Verstärkeranschluss: Phono MMKanalabweichung bei 1 kHz: 2dBÜbersprechdämpfung bei 1kHz: 22dBÜbersprechdämpfung bei 15kHz: 15dBFrequenzgang: 20-20.000Hz ±2dBAbtastfähigkeit bei 315Hz: 65µm**Nadelnachgiebigkeit: 20µm/mNempf. Tonarm-Typ: mittelschwer und schwer***Abtastdiamant: elliptischVerrundung: r/R 8/18µmAuflagekraftbereich: 15-20mN (1,5-2,0g)empf. Auflagekraft: 17,5mN (1,75g)Abtastwinkel: 20 GradGleichstromwiderstand:750 OhmInduktivität: 450mHempf. Abschlusswiderstand 47kOhmempf. Abschlusskapazität 200-500pFHöhe: 18mmGewicht: 2,5g (5g mit einliegendem Zusatzgewicht). ***ohne eingelegtes Zusatzgewicht für schwere Tonarme geeignetErsatz-Nadeleinschub: Stylus 5E*bei 1000Hz, 5cm/sec. **bei empfohlener Auflagekraft Höhe = Abstand von der Diamantspitze zur Deckelplatte Normal 0 21 false false false DE X-NONE X-NONE MicrosoftInternetExplorer4 „Der Verkauf erfolgt unter Ausschluss jeglicher Sachmängelhaftung. Die Haftung auf Schadenersatz wegen Verletzungen von Gesundheit, Körper oder Leben und grob fahrlässiger und/oder vorsätzlicher Verletzungen meiner Pflichten als Verkäufer bleibt davon unberührt.“

Sehr gut erhaltene Ortofon Headshell. Der Tonabnehmer ist gratis dabei, keine Ahnung ob der ok ist. Very well kept Ortofon headshell. The pickup is a free gift, no clue if its ok.

ORTOFON 2M Red CARTRIDGE THIS IS A NEW ORTOFON 2M Red CARTRIDGE WITH THE NEW ORIGINAL Red ORTOFON STYLUS. IT IS MOUNTED ON A NEW LOW MASS METAL HEADSHELL. STYLUS OVERHANG SET--READY TO PLUG IN & PLAY. OVERHANG GAUGE SHOWN IN ONE PHOTO NOT INCLUDED. PERFECT FOR SME S SHAPED TONEARMS USING THE STANDARD 1/2 PLUG IN HEADSHELL. CARTRIDGE WAS NEVER USED OR MOUNTED UNTIL NOW.IT COMES WITH ALL THE ORIGINAL ORTOFON PACKAGING. SOME SPECS; output voltage: 5.5mVfrequency response: 20 ~ 20Hz +3/-1dBtracking force range: 1.5 ~ 2.0gtracking angle: 20 degreesdiamond elliptical stylusweight 7.2 gramsYou must be happy or return in 30 days for a refund-less shipping both ways. Please e-mail any questions See our other auctions for vintage audio and hard to find turntable/speaker parts. Thanks again for looking and happy bidding! BID WITH CONFIDENCE Check our feedback We know how to pack & ship 35 years repairing/restoring turntables The turntableexperts . Track Page Views With Auctivas Counter

Ortofon SPU M Bakelite Headshell, mit Schrauben, Kabel und Box. Sehr guter Zustand. Weitere Headshells in meinen anderen Angeboten.

SME 3009 Series II Improved Tonearm, Fixed Headshell, complete with Ortofon 520 MKII cartridge. Good working order and condition. I have given the tonearm a light clean but you may wish to fully disassemble and give it a thorough clean. Please see the pictures for a full condition report. Includes original SME tonearm wiring, anti skate weight and brochure. TERMS & CONDITIONSIMPORTANT - PLEASE READ BEFORE PURCHASING 1. Returns 1.1 All items are sold with either a 14 or 30 day return policy as stated in the listing. Please contact us as soon as possible in the unlikely event that your item arrives not as described and we will be sure to resolve the issue. Abuse of the return policy is in breach of eBays T&Cs. Products may be invisibly security marked. All unscrupulous buyers will be reported and an action fraud case will be opened. 1.2 If goods are returned as surplus to your requirement and are not faulty on receipt, a restocking charge of 20% will apply. 2. Power Cables 2.1 In order to reduce electronic waste, unless stated, units that require standard IEC kettle or figure of eight power cables will not be included unless requested. If you require one, please let us know immediately after purchasing and we will include one free of charge. 3. International / Non Mainland UK Buyers 3.1 Most of our items are available to purchase via eBays global shipping program. If postage costs are not displayed to you, please contact us before pressing buy it now and we will try to find a solution. 4. General/Other 4.1 All of our shipments are carefully packaged to ensure safe carriage. All fragile packages are clearly marked as fragile and we do our utmost to ensure that they arrive to you intact. Recycled packaging materials will be made use of where appropriate. Thank you for looking, happy eBaying!

Ortofon Headshell und SHURE V15 III TM Plattenspieler Nadel Vinyl Schallplatte. Wurde nie genutzt. Quasi wie neu.

the normal selling price is 945 EUR .Here you have the opportunity to purchase this tonearm at a reasonable price Do you miss the times when craftsmanship was important? When working in-house. When a product went from idea to completion under the same roof. Me too. Thats why I make my tonearms with great attention to detail and with the highest level of craftsmanship. the results! They make everything worthwhile. Inspired by golden age of ORTOFON Tonearms solid brass tonearm material has always been Ortofons first choice for their tonearmsfor example :RF-309,RK-309 and much moretherefore, from now on, all my Ortofon tonearms are made of solid brass with a sandblasted surface, which suppresses enormously unwanted resonance. For this reason, EMT has given the EMT 997 head part, counterweight and montage base a special black paint that has a rough surface******************************************************************************* the so-called resonance curve, the width of which is a measure of the quality of the vibration. Brass has a very narrow resonance curve (compared to e.g. aluminium), which speaks for high quality, low damping and thus its suitability for building bells or similar. From the relationship between the length of the rod and the wavelength, it is very easy to calculate the speed of sound in the respective substance (a few thousand meters per second in the case of metals) in the case of resonance. Measurement result: perfectly controlled vibration behavior no sound-influencing natural resonances drastically minimized Impact: supremely open and contoured music reproduction excellent transparency holographic three-dimensionality excellent detail precision Broadcast Tonearm Ortofon AB -309 banana IMPROVED 12 long for Ortofon SPU-G and SME type Headshellsincluded with continuous wiring ONE OF THE BEST 12 LONG TONEARMS(thats what my customers write to me)MADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AB-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AB-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..****************************************************************________________________________________________________________________ anti skating adjustment screw for azimuth adjustment. Headshell original Ortofon from the 70s completely made of solid brass, rare to find, I was able to store some the first cable in every audio system is the most important, as information can never be recreated once its lost in the first place.No phono preamp and amplifier, no matter how good and expensive, can undo that My tonearm cable started as a project to build a correct tonearm cable design for my highest rated tonearms, as none in the market offers all the right ingredients that support my Extreme phono philosophy for correct music reproduction. the cable I developed myself (air as the dielectric) has the worlds lowest cable capacity. Total length 1.6 m = 51 pF / = 10.2 pF per foot .for comparison ,the CARDAS Clear Audio cable has 16pF per foot and costs 1,680 euros NEUTRIC/REAN RCA NYS373Lifetime >5000 Mating Cycles Introducing REAN, a global brand from the Neutrik Group, marrying over 45 years of precision engineering know-how with our own dedicated state-of-the-art production facilities. comes with HeadshellHeadshell is CNC high precision machined from a single block of aircraft grade aluminum, Lightness and durability high quality aluminumGold anodized aluminium, so it is a durable treatment that resists scratching and marring The terminals are made of high quality Sn-P bronze with high conductivity 24K GOLD plating Sn-P bronze is an elastic copper-based alloy with the requirements of high accurate of dimension, good surface quality, excellent shape of strip and properties for production. Each terminal end is wrapped in color coded shrink tubing. Terminals are hand soldered. Color-coded heat shrink is used at the cartridge end, black heat shrink at the head shell end. anti-skating mechanism is now housed in the housing and can no longer get dirty Telefunken/Ortofon AS-212 made from aluminum and vulnerable antiskating ***************************************************************** Since 2013, my Ortofon tonearms have received worldwide the highest ratings from my customershere are just a few of hundreds of enthusiastic customers*************************************************************************************** Finally, the arm sounds just great. I run it with my DL103s and classic SPUs and it does not fall behind a 3012 being completely refurbished by ATA.(whatsbestforum Febr.14.2022)IMHO, Alfreds tonearms compare very favorably with my original Ortofon RMG309, the RMG309i above and SME 3012.(whatsbestforum Febr 14,2022) I have been using Alfreds arm for about 6 months now. I must say it has very low distortion, and the bass is clearly better than my SME3012; more extended and has more weight. I have been doing comparisons between my LPs and tapes, and some LPs are holding their own against master tapes. (whatsbestforum Oct 12,2022) I must say the more I listen to my Bokrand tonearm, the more amazed I am with the sound quality. It has a very solid bottom end and very low distortion. I just dont know how people can live with 9 tonearms. I dont have a lot of experience with ultra-expensive arms, but I can say that the Bokrand is superior to the Graham 2.2 I have owned in the past, and even the SME 3012R. (whatsbestforum Dec 5, 2022)Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. **************************************************************************** horizontal bearing original Ortofon*************************a rough surface strongly suppresses unwanted resonancestherefore all parts are sandblasted to achieve a rough surfaceafter sandblasting, all parts are baked in the oven with matt silver paint ****************************************** 2 DIFFERENT COUNTER WEIGHTS thanks to the different weights, the tonearm has a variable mass of 18.5 to 25 grams 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE SHIPPINGTRACKING AND REGISTERED POST

the normal selling price is 725 EUR. Here you have the opportunity to purchase this tonearm at a reasonable price ************************************************here is one of the last feedbacks from july 30thAligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extendedand the too end extended and sweet. No ringing or tonal artifacts with this arm.Vocals are on par with the best of the best. Rich defined and harmonically perfect. Thank you sir. Well done! Robin Wyatt Miyajima Labs USA importer.********************************************************************************** Broadcast Tonearm Ortofon AS -309 12 long for Ortofon SPU-G and SME typeHeadshells MADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º continuous wiring included from the Headshell to the RCA´s with silver plated copper litz from USA This tonearm does not have a fixed effective mass, but is variable due to its different counter weights and the distance to the pivot point of the tonearm It is one of the very rare tonearms with variable mass worlwide.A tonearm with variable effective mass, which makes it possible to use all cartridges with low compliance or with high compliance.************************************************ connector fits Ortofon SPU-G and SME type Headshells Improved base maximum stability and less resonance all my Ortofon Tonearms have the same bearingshighest industry standard and sealed maintenance free ***************************** here YouTube video from a satisfied customerGarrard 301 with my Ortofon AS-309 12 long Tonearm https://www.youtube.com/watch?v=cHzdUsc9Zm4&list=PLZIpztUGDMFS2-0dzexJp-sEkUTes5Zdr ********************************************RCA´s REAN brand from NEUTRIK,the worlds leading supplier of professional audio and video connectors – Neutrik AG *********************************** PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º_____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE RMG-309 ORTOFON AS-309 12 long compared to ORTOFON RMG-309 SPECIFICATIONS AS-309 RMG-309 pivot to spindle (mm) 308.81 309 effective length (mm) 321.46 320 overhang (mm) 12.65 11 offset angle ° 16.9 15.9 maximum error ° 1.28 1.69 maximum distortion % 0.44 0.58 average rms distortion % 0.29 0.35 all results taken fromvinylengineTonearm Alignment Calculator Pro Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises. if the distortions are very high, because the geometry of the armtube is bad, then helps no ball bearings from NASA or whatever. Many manufacturers want to persuade one. it also no helps no arm tube, made of 500 years old wood, which is the specially manufactured and polished by moonlight from a virgin.**************************************************************** The Armwand is high damped with inlet of Balsa Wood(the inlet of balsa for damping is precisely balanced- when you overdamped you will take the life out of the sound and it will get boring)********************************************************************* Armwand with matt surface and inlet of balsa woodwhich guarantees no resonances in Armtube and CartridgeYOU WILL HEAR THIS.********************************************************************************** continuous internal wiring from the headshell plug to the RCAloom steel braid and PET braid to ensure enhanced signal flow and screening due to the use of a Faraday cage to kill off RF. this is the best what do you can do you not need a expensive tonearm cable buy *********************************************************the benefit of continuous internal wiring from the headshell plug to the RCA *************************************************************** my cable have only 57 pF at 1.2 m in length; the Genesis cable have 135 pF at 1.2 m in length and cost $ 549 high capacities affect and eliminate high and mid frequencies and ruin the original music information ************************************** 2 DIFFERENT COUNTER WEIGHTS2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMSor BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges**************************************** **************************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUAL SCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICE _____________________________ WORLDWIDE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much.

For the audiophiles all over the world ORTOFON products reach legendary status. And thats rightfully. This is a opportunity to own whats becoming rare and more expensive on the world market. Excellent tonearm for serious music lovers ********************Broadcast Tonearm Ortofon AB -309 banana 12 long for Ortofon SPU-G and SME type Headshells ONE OF THE BEST 12 LONG TONEARMSMADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AS-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..**************************************************************** positive feedbacks Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. _______________________________ My Ortofon tonearms go over the SME 3012 and SME 3012R, which costs about 5000 euros. It is only surpassed by a GLANZ for $11,000. Thats not what Im saying, but my customers.see here original mailsDear mr. BokrandI gave myself some time to make sure I wasn’t too hasty in judging. After many hours of listening to my favorite records, which I know very well, I can say that your arm holds up very well the comparison with my beloved SME 3012R, indeed, with the Ortofon SPU is superior in clarity, dynamics (!!!), soundness of bass...Thanks for everythingMassimo Longoni________________________________________________________________________ screw for setting Azimuth 2 DIFFERENT COUNTER WEIGHTS 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges _________________________________________________ liftlever is modified by me in the vintage Ortofon style like the Ortofon Hi Jack.I like this classic timeless style ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE FREE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much. Wolfgang (email from 30.12.2016) Hello Alfred, I have been wanting to tell you that I have been enjoying your tonearm so very much ! The set up was easy, thank you for the template and alignment tool, it is very precise. The quality of the tonearm is excellent, of course, and I have already found the split counterweight very useful. I have been trying the arm with a Denon 103 and an Ikeda 9C cartridge, and both sound wonderful. The Ikeda requires much more attention to alignments, and your tonearm makes that very simple. It is also nice to have the anti skate adjustment too, which helps a lot with the ikeda. More than anything, Im enjoying music, which is more important than any technicalities. I will send you photos soon of my turntable setup so you may see everything in its happy state. My turntable is a Garrard 401. With many thanks again, in gratitude for your fine work and dedication, S.M New York 17.Sept. 2014 Hallo Alfred, es ist vollbracht. In ca. 3 Tagen habe ich die Zarge für den Neuen aufgebaut.Die ersten Platten drehen sich seit gestern auf dem Ortofon-Bokrand Sp-15.Schon erstaunlich was da aus meinen Eckhörnern kommt.Ich kann ihn nur mit meinem EMT 948 vergleichen mit dem ich seit ca. 1 Jahr sehr intensiv höre.Ich hab das Gefühl, dass das Gespann des Neuen sehr nahe an Perfektion ist und das für ca. 1/3 des Preises des 948!Vielen Dank für deine tolle Arbeit an dem Tonarm! Thomas K.(Germany) 28.12.2012 ORTOFON 12 long with TECHNICS SP-15 from Thomas K. Hi Alfred. I have been using this tone arm with my Garrard 301 / mono Ortofon Spu cartridge. It sounds absolutely superb. I must congratulate you on your fine work. Have you had a chance to post the Ortofon Head shell yet? I am looking forward to using this with my Shure V15mxr cartridge. Many thanks. John ----- Original Message -----Sent: Tuesday, August 14, 2012 6:23 PM Subject: AW: Re: Ortofon Tone Arm Dear Alfred I have finally set up the tonearm and listened to LPs with it. I have to say that it is better than some of my other arms, possibly because of the strong arm tube.(FROM FSK HONG KONG)Hi Alfred, Glad to tell you that I have received and installed the tonearm after some hard work. Sound is great ! Still take some time for the cartridge to break-in but the tracking ability is extraordinary which allows any music to sing beautifully. Otherwise, it seems perfect to me. Thank you for your help ! Hi Alfred, The system actually sounds better and better from day to day. Impressive particular for old LPs. While writing to you, I am listening to the original Moon River of Andy William. The Exdous Song has never sound so good before - Superb !(Original text email from Japan)Dear Alfred I have at last set up your arm and can now give you an early impression of the sound. Beautifully balanced throughout the frequency range, no irritating frequencies stand out. Air and focus are superb. It is very musical with excellent pitch. Tonal range is very even handed and smooth. However the overall feeling is best summed up by saying that it sounds right in particular piano takes on the feel of one you have grown to recognise from your days in school plays.(Original text of the email from UK)---------------------------------------------------------------------Hello Alfred, I received the new cable yesterday afternoon.Thank you very much for your fast and kindly support.At last, I was able to listen to the sound of your special tonearm. WOW ! Excellent !! I love it.I always use DENON DL103-LC2(?? as a standard cartridgetesting the change of the sound. It was still the result of the short time test, but I felt the sound wassplendid.Lower background-noise, wide and deep sound-stage, particularlythe sonority is very natural and clear.(original mail from Mr.T. Japan)_______________________________________________________ Good morning Alfred, Well, yesterday I mounted your arm on the plinth with the SPU Meister Silver. Mounting was a breeze using my tool for determining the spindle to pivot distance. Using the dual counterweight it is also very easy to tune for optimal stylus pressure, at least far more easy than when using one counterweight. So that is a practical plus for the dual counterweights above the ability for mounting less heavy cartridges as well.I asked you before how your tonearm would compare to the Schick and you were modest. No need to! It is so much better than the Schick when using the heavy SPU.. really, it performs better on from low up to the high frequencies. I have been listening, or actually rediscovering, lots of records sinds yesterday afternoon. I always found that the SPU had at some records a bit of harsh highs but these are completely gone now. So that must have been the combination with the Schick, is my guess. Resonances are way better suppressed now and I do believe that the heavy and sturdy construction does not allow for any other movement of the cartridge/needle than lateral movement.I bow deep for your expertise as that must be the basis of the reconstructed Ortofon! We are really impressed here! My suggestion is that I buy two more arms from you. So I keep the one that is on my turntable now and you send over two complete tonearms. These two consist of the one that you customised for me and another one.I want to replace the Schick with a second AB309 and the third will be for a friend who started dancing in my room when he heard your tonearm..So all together:1. I will keep the tonearm I currently have. This one will go to my friend as he likes the J-shaped armtube.2. The customised arm by you, complete with mounting stuff and counterweights, will replace the one that will go to my friend.3. The third tonearm will replace the Schick tonearm on my plinth. So that is a whole new arm.DHT Rob Netherland 02/12/2018 pictures received from satisfied customers IF YOU ARE NOT SATISFIED,MONEY BACK GUARANTEE***************************************

For the audiophiles all over the world ORTOFON products reach legendary status. And thats rightfully. This is a opportunity to own whats becoming rare and more expensive on the world market. Excellent tonearm for serious music lovers ********************Broadcast Tonearm Ortofon AB -309 banana 12 long for Ortofon SPU-G and SME type Headshells ONE OF THE BEST 12 LONG TONEARMSMADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AS-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..**************************************************************** positive feedbacks Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. _______________________________ My Ortofon tonearms go over the SME 3012 and SME 3012R, which costs about 5000 euros. It is only surpassed by a GLANZ for $11,000. Thats not what Im saying, but my customers.see here original mailsDear mr. BokrandI gave myself some time to make sure I wasn’t too hasty in judging. After many hours of listening to my favorite records, which I know very well, I can say that your arm holds up very well the comparison with my beloved SME 3012R, indeed, with the Ortofon SPU is superior in clarity, dynamics (!!!), soundness of bass...Thanks for everythingMassimo Longoni________________________________________________________________________ screw for setting Azimuth 2 DIFFERENT COUNTER WEIGHTS 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges _________________________________________________ liftlever is modified by me in the vintage Ortofon style like the Ortofon Hi Jack.I like this classic timeless style ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE FREE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much. Wolfgang (email from 30.12.2016) Hello Alfred, I have been wanting to tell you that I have been enjoying your tonearm so very much ! The set up was easy, thank you for the template and alignment tool, it is very precise. The quality of the tonearm is excellent, of course, and I have already found the split counterweight very useful. I have been trying the arm with a Denon 103 and an Ikeda 9C cartridge, and both sound wonderful. The Ikeda requires much more attention to alignments, and your tonearm makes that very simple. It is also nice to have the anti skate adjustment too, which helps a lot with the ikeda. More than anything, Im enjoying music, which is more important than any technicalities. I will send you photos soon of my turntable setup so you may see everything in its happy state. My turntable is a Garrard 401. With many thanks again, in gratitude for your fine work and dedication, S.M New York 17.Sept. 2014 Hallo Alfred, es ist vollbracht. In ca. 3 Tagen habe ich die Zarge für den Neuen aufgebaut.Die ersten Platten drehen sich seit gestern auf dem Ortofon-Bokrand Sp-15.Schon erstaunlich was da aus meinen Eckhörnern kommt.Ich kann ihn nur mit meinem EMT 948 vergleichen mit dem ich seit ca. 1 Jahr sehr intensiv höre.Ich hab das Gefühl, dass das Gespann des Neuen sehr nahe an Perfektion ist und das für ca. 1/3 des Preises des 948!Vielen Dank für deine tolle Arbeit an dem Tonarm! Thomas K.(Germany) 28.12.2012 ORTOFON 12 long with TECHNICS SP-15 from Thomas K. Hi Alfred. I have been using this tone arm with my Garrard 301 / mono Ortofon Spu cartridge. It sounds absolutely superb. I must congratulate you on your fine work. Have you had a chance to post the Ortofon Head shell yet? I am looking forward to using this with my Shure V15mxr cartridge. Many thanks. John ----- Original Message -----Sent: Tuesday, August 14, 2012 6:23 PM Subject: AW: Re: Ortofon Tone Arm Dear Alfred I have finally set up the tonearm and listened to LPs with it. I have to say that it is better than some of my other arms, possibly because of the strong arm tube.(FROM FSK HONG KONG)Hi Alfred, Glad to tell you that I have received and installed the tonearm after some hard work. Sound is great ! Still take some time for the cartridge to break-in but the tracking ability is extraordinary which allows any music to sing beautifully. Otherwise, it seems perfect to me. Thank you for your help ! Hi Alfred, The system actually sounds better and better from day to day. Impressive particular for old LPs. While writing to you, I am listening to the original Moon River of Andy William. The Exdous Song has never sound so good before - Superb !(Original text email from Japan)Dear Alfred I have at last set up your arm and can now give you an early impression of the sound. Beautifully balanced throughout the frequency range, no irritating frequencies stand out. Air and focus are superb. It is very musical with excellent pitch. Tonal range is very even handed and smooth. However the overall feeling is best summed up by saying that it sounds right in particular piano takes on the feel of one you have grown to recognise from your days in school plays.(Original text of the email from UK)---------------------------------------------------------------------Hello Alfred, I received the new cable yesterday afternoon.Thank you very much for your fast and kindly support.At last, I was able to listen to the sound of your special tonearm. WOW ! Excellent !! I love it.I always use DENON DL103-LC2(?? as a standard cartridgetesting the change of the sound. It was still the result of the short time test, but I felt the sound wassplendid.Lower background-noise, wide and deep sound-stage, particularlythe sonority is very natural and clear.(original mail from Mr.T. Japan)_______________________________________________________ Good morning Alfred, Well, yesterday I mounted your arm on the plinth with the SPU Meister Silver. Mounting was a breeze using my tool for determining the spindle to pivot distance. Using the dual counterweight it is also very easy to tune for optimal stylus pressure, at least far more easy than when using one counterweight. So that is a practical plus for the dual counterweights above the ability for mounting less heavy cartridges as well.I asked you before how your tonearm would compare to the Schick and you were modest. No need to! It is so much better than the Schick when using the heavy SPU.. really, it performs better on from low up to the high frequencies. I have been listening, or actually rediscovering, lots of records sinds yesterday afternoon. I always found that the SPU had at some records a bit of harsh highs but these are completely gone now. So that must have been the combination with the Schick, is my guess. Resonances are way better suppressed now and I do believe that the heavy and sturdy construction does not allow for any other movement of the cartridge/needle than lateral movement.I bow deep for your expertise as that must be the basis of the reconstructed Ortofon! We are really impressed here! My suggestion is that I buy two more arms from you. So I keep the one that is on my turntable now and you send over two complete tonearms. These two consist of the one that you customised for me and another one.I want to replace the Schick with a second AB309 and the third will be for a friend who started dancing in my room when he heard your tonearm..So all together:1. I will keep the tonearm I currently have. This one will go to my friend as he likes the J-shaped armtube.2. The customised arm by you, complete with mounting stuff and counterweights, will replace the one that will go to my friend.3. The third tonearm will replace the Schick tonearm on my plinth. So that is a whole new arm.DHT Rob Netherland 02/12/2018 pictures received from satisfied customers IF YOU ARE NOT SATISFIED,MONEY BACK GUARANTEE***************************************

the normal selling price is 725 EUR. Here you have the opportunity to purchase this tonearm at a reasonable price ************************************************here is one of the last feedbacks from july 30thAligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extendedand the too end extended and sweet. No ringing or tonal artifacts with this arm.Vocals are on par with the best of the best. Rich defined and harmonically perfect. Thank you sir. Well done! Robin Wyatt Miyajima Labs USA importer.********************************************************************************** Broadcast Tonearm Ortofon AS -309 12 long for Ortofon SPU-G and SME typeHeadshells MADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º continuous wiring included from the Headshell to the RCA´s with silver plated copper litz from USA This tonearm does not have a fixed effective mass, but is variable due to its different counter weights and the distance to the pivot point of the tonearm It is one of the very rare tonearms with variable mass worlwide.A tonearm with variable effective mass, which makes it possible to use all cartridges with low compliance or with high compliance.************************************************ connector fits Ortofon SPU-G and SME type Headshells Improved base maximum stability and less resonance all my Ortofon Tonearms have the same bearingshighest industry standard and sealed maintenance free ***************************** here YouTube video from a satisfied customerGarrard 301 with my Ortofon AS-309 12 long Tonearm https://www.youtube.com/watch?v=cHzdUsc9Zm4&list=PLZIpztUGDMFS2-0dzexJp-sEkUTes5Zdr ********************************************RCA´s REAN brand from NEUTRIK,the worlds leading supplier of professional audio and video connectors – Neutrik AG *********************************** PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.65 mmOFFSET ANGLE (DEGREES): 16.89 º_____________________________________________________________========================== ORTOFON 12 AS-309 TONEARM HAVE LESS DISTORSIONS AS THE RMG-309 ORTOFON AS-309 12 long compared to ORTOFON RMG-309 SPECIFICATIONS AS-309 RMG-309 pivot to spindle (mm) 308.81 309 effective length (mm) 321.46 320 overhang (mm) 12.65 11 offset angle ° 16.9 15.9 maximum error ° 1.28 1.69 maximum distortion % 0.44 0.58 average rms distortion % 0.29 0.35 all results taken fromvinylengineTonearm Alignment Calculator Pro Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises. if the distortions are very high, because the geometry of the armtube is bad, then helps no ball bearings from NASA or whatever. Many manufacturers want to persuade one. it also no helps no arm tube, made of 500 years old wood, which is the specially manufactured and polished by moonlight from a virgin.**************************************************************** The Armwand is high damped with inlet of Balsa Wood(the inlet of balsa for damping is precisely balanced- when you overdamped you will take the life out of the sound and it will get boring)********************************************************************* Armwand with matt surface and inlet of balsa woodwhich guarantees no resonances in Armtube and CartridgeYOU WILL HEAR THIS.********************************************************************************** continuous internal wiring from the headshell plug to the RCAloom steel braid and PET braid to ensure enhanced signal flow and screening due to the use of a Faraday cage to kill off RF. this is the best what do you can do you not need a expensive tonearm cable buy *********************************************************the benefit of continuous internal wiring from the headshell plug to the RCA *************************************************************** my cable have only 57 pF at 1.2 m in length; the Genesis cable have 135 pF at 1.2 m in length and cost $ 549 high capacities affect and eliminate high and mid frequencies and ruin the original music information ************************************** 2 DIFFERENT COUNTER WEIGHTS2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMSor BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges**************************************** **************************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUAL SCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICE _____________________________ WORLDWIDE SHIPPINGTRACKING AND REGISTERED POST------------------------------------------- reviews from customers( Original text e-mails) from HiFi Wigwam:The Ortofon arm is one of the ones off ebay done by a German guy in Spain (Alfred Bokrand), based on the old (Danish-made) Ortofon AS212/309 bearing housing and anti-skate mechanism, with an arm tube and weights of his own design. I think its a wonderful bit of kit, I prefer it to the Thomas Schick arm that I used to have, which I had bias problems with, this is properly adjustable. Its a ridiculous bargain for the £500 or so hes charging for it. This 301 has a very special tonearm. It was made by Alfred Bokrand from an Ortofon AS-212 on which he has placed a 12? wand. The workmanship is first class and it tracks like a dream. This model of Ortofon arm is known for its pivot set up- it has wonderful bearings, it has a two part counter weight that will allow for a SPU with built in transformer......============================================================== Dear Alfred. I finally set up the tonearm and I am more than satisfied with the results. It has been a huge improvement in my musical experience. The tonearm is piece of beauty and perfect enginered for music reproduction. The classical records sound heavenly good and Jazz albums never as intimate. The severe wrapped records do never miss the track. The bass response is clean and solid. Great. Thanks for your patience with my issues and I am very grateful for send me another cable. Happy new year Afectuosamente Ignacio Enviado desde mi iPhone (email from 28.12.2016)Hi Alfred Just letting you know that the tonearm arrived safe and sound.I have installed it on a 16 broadcast turntable and it sounds great (and looks good as well). Thank you very much.

the normal selling price is 945 EUR .Here you have the opportunity to purchase this tonearm at a reasonable price Do you miss the times when craftsmanship was important? When working in-house. When a product went from idea to completion under the same roof. Me too. Thats why I make my tonearms with great attention to detail and with the highest level of craftsmanship. the results! They make everything worthwhile. Inspired by golden age of ORTOFON Tonearms solid brass tonearm material has always been Ortofons first choice for their tonearmsfor example :RF-309,RK-309 and much moretherefore, from now on, all my Ortofon tonearms are made of solid brass with a sandblasted surface, which suppresses enormously unwanted resonance. For this reason, EMT has given the EMT 997 head part, counterweight and montage base a special black paint that has a rough surface******************************************************************************* the so-called resonance curve, the width of which is a measure of the quality of the vibration. Brass has a very narrow resonance curve (compared to e.g. aluminium), which speaks for high quality, low damping and thus its suitability for building bells or similar. From the relationship between the length of the rod and the wavelength, it is very easy to calculate the speed of sound in the respective substance (a few thousand meters per second in the case of metals) in the case of resonance. Measurement result: perfectly controlled vibration behavior no sound-influencing natural resonances drastically minimized Impact: supremely open and contoured music reproduction excellent transparency holographic three-dimensionality excellent detail precision Broadcast Tonearm Ortofon AB -309 banana IMPROVED 12 long for Ortofon SPU-G and SME type Headshellsincluded with continuous wiring ONE OF THE BEST 12 LONG TONEARMS(thats what my customers write to me)MADE BY ALFRED BOKRANDGERMAN BROADCAST ENGINEER(RADIO+TV) WHY?PHYSICS and GEOMETRY never lies.....THIS ARMWAND IS OPTIMIZED FORLOWEST TRACKING DISTORSION3 THINGS DETERMINE THE QUALITY AND THE PERFORMANCE OF A PERFECT TONEARM:1) EFFEKTIVE LENGHT 2) OVERHANG3) OFFSET ANGLE============================ TONEARM GEOMETRY:EFFEKTIVE LENGTH : 321.459 mm MOUNTING DISTANCE: 309.4mmOVERHANG: 12.66 mmOFFSET ANGLE (DEGREES): 16.9 º _____________________________________________________________========================== ORTOFON 12 AB-309 TONEARM HAVE LESS DISTORSIONS AS THE SME 3012 series I ORTOFON AB-309 12 long compared to SME 3012 series I 309.4 mm mounting distance 294 mm 321.5 mm effektive lenght 305 mm 12.6 mm Over hang 11 mm 16.9 º offset angle(degrees) 16.15 º 1.26 º maximum error º 2.11 º 0.3 % average distorsion 0.36 % 0.46 % maximum distorsion 0.72 % all results taken fromAlignment Calculator Provinylengine page Tonearm geometry with the lowest distortion worldwide, you will hear it immediately the geometry had to be calculated by hand in the 60s, because you did not have any computer calculation programs yet, this could never be the optimum, because the 3 parameters for the geometry are interdependent. When you change only one parameter to 0.5mm the distortions are great. Therefore, tonearms from the 60s can NEVER reach the perfection that is possible with the computer programs today___________________________________This tonearm combines the simple aesthetics of Ortofon Tonearms with the current best armtube geometry currently available only a perfect geometry of the armtube guarantees a low distortion.this is the first and most important thing with a tonearm.not the material, not exotic armtube materials or mimics can eliminate a fundamental distortion that exist due to a wrong and bad geometry.material of the armtube and Vaccination only has an impact on resonance and vibration coming from the plinth (engine vibration and music waves) tonal arms are offered on the market, which cost well over $ 15,000 and are advertised that give the materials the highest in technology (space travel, NASA ect) the geometry of a perfect tonearm with the lowest distorsions consists of: 1) effective length2) overhang3) offset angle nothing more and nothing less these 3 parameters are dependent on each other. This is mathematics and is based on formulas that have absolutely nothing to do with materials. With existing PC calculation programs, anyone can see if their tonearm has the least distortion due to the armtube geometry. This is the only objective method and not the subjective belief in exotic materials or great promises..****************************************************************________________________________________________________________________ anti skating adjustment screw for azimuth adjustment. Headshell original Ortofon from the 70s completely made of solid brass, rare to find, I was able to store some the first cable in every audio system is the most important, as information can never be recreated once its lost in the first place.No phono preamp and amplifier, no matter how good and expensive, can undo that My tonearm cable started as a project to build a correct tonearm cable design for my highest rated tonearms, as none in the market offers all the right ingredients that support my Extreme phono philosophy for correct music reproduction. the cable I developed myself (air as the dielectric) has the worlds lowest cable capacity. Total length 1.6 m = 51 pF / = 10.2 pF per foot .for comparison ,the CARDAS Clear Audio cable has 16pF per foot and costs 1,680 euros NEUTRIC/REAN RCA NYS373Lifetime >5000 Mating Cycles Introducing REAN, a global brand from the Neutrik Group, marrying over 45 years of precision engineering know-how with our own dedicated state-of-the-art production facilities. comes with HeadshellHeadshell is CNC high precision machined from a single block of aircraft grade aluminum, Lightness and durability high quality aluminumGold anodized aluminium, so it is a durable treatment that resists scratching and marring The terminals are made of high quality Sn-P bronze with high conductivity 24K GOLD plating Sn-P bronze is an elastic copper-based alloy with the requirements of high accurate of dimension, good surface quality, excellent shape of strip and properties for production. Each terminal end is wrapped in color coded shrink tubing. Terminals are hand soldered. Color-coded heat shrink is used at the cartridge end, black heat shrink at the head shell end. anti-skating mechanism is now housed in the housing and can no longer get dirty Telefunken/Ortofon AS-212 made from aluminum and vulnerable antiskating ***************************************************************** Since 2013, my Ortofon tonearms have received worldwide the highest ratings from my customershere are just a few of hundreds of enthusiastic customers*************************************************************************************** Finally, the arm sounds just great. I run it with my DL103s and classic SPUs and it does not fall behind a 3012 being completely refurbished by ATA.(whatsbestforum Febr.14.2022)IMHO, Alfreds tonearms compare very favorably with my original Ortofon RMG309, the RMG309i above and SME 3012.(whatsbestforum Febr 14,2022) I have been using Alfreds arm for about 6 months now. I must say it has very low distortion, and the bass is clearly better than my SME3012; more extended and has more weight. I have been doing comparisons between my LPs and tapes, and some LPs are holding their own against master tapes. (whatsbestforum Oct 12,2022) I must say the more I listen to my Bokrand tonearm, the more amazed I am with the sound quality. It has a very solid bottom end and very low distortion. I just dont know how people can live with 9 tonearms. I dont have a lot of experience with ultra-expensive arms, but I can say that the Bokrand is superior to the Graham 2.2 I have owned in the past, and even the SME 3012R. (whatsbestforum Dec 5, 2022)Aligned. It is in an aftermarket VTA tower made for the Groovmaster IIti that was on the table before your arm. I will not going back to the GM!!! Only my $11,000 Glanz MH124 is superior and not by $10,000! I am thrilled at this arms performance richness of tone is its major strong point. Bass is tight super extended and the too end extended and sweet. No ringing or tonal artifacts with this arm. Vocals are on par with the best of the best. Rich defined and harmonical. Thank you sir. Well done! Robin WyattMiyajima Labs USA importer. **************************************************************************** horizontal bearing original Ortofon*************************a rough surface strongly suppresses unwanted resonancestherefore all parts are sandblasted to achieve a rough surfaceafter sandblasting, all parts are baked in the oven with matt silver paint ****************************************** 2 DIFFERENT COUNTER WEIGHTS thanks to the different weights, the tonearm has a variable mass of 18.5 to 25 grams 2 WEIGHTS TOGETHER FOR ORTOFON SPU-G CARTRIDGS UP TO 35 GRAMS or BIG COUNTER WEIGHT SINGLY FOR CARTRIDGES UP TO 20 GRAMS With this construction you have an enormous range of applications for all Cartridges ******************************** TONEARM COMES WITH :MOUNTING TEMPLATEMANUALSCREWS AND WASHERS FOR MOUNTING COLLARALLEN KEY FOR ADJUST LIFT DEVICESCREW DRIVER FOR WEIGHTSSCREW DRIVER FOR AZIMUTH ADJUST in the manual you will always find an original sample of the internal wiring WORLDWIDE SHIPPINGTRACKING AND REGISTERED POST