MCV Audio Lübeck 2007 Nakamichi Audio Cinch Cable,, RCA 1,0 Meter Kabellänge! Artikelbeschreibung Optisch und technisch ist der Artikel in einem guten gebrauchten Zustand. Bitte alle Bilder anschauen, die Bilder sind Bestandteil der Beschreibung. Visually and technically the item is in good used condition. The pictures are essential part of the item description. Please look at the pictures. LIEFERUMFANG / Delivery 1x Nakamichi Audio Cinch Cable,, RCA 1,0 Meter Differenzbesteuerter! Artikel wird verkauft nach §25aUStG ohne MwSt-Ausweis. Auf Verpackung und Versand wird grossen Wert gelegt. Alle unsere Artikel gehen bestens verpackt aus unserem Hause. Die Lieferung erfolgt falls in Grösse und Gewicht möglich ausschliesslich mit DHL, der deutschen Post oder Hermes MCV-Audio LübeckInhaber: M.Topal 23560 Lübeck

Nakamichi CA5 RCA PCB Board Part For Repair. Please check to make sure this is the part you need. I am going on memory with a lot of these.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube. AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound. Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

4 Gold Plated Nakamichi RCA Plug Locking Non solder plug connector. Plugs are brand new, never used. Buyer pays a fixed $5.00 shipping and handling. Thanks for looking.

Vintage tonearm made by Micro Seiki for Luxman. Arm was removed from a clean Luxman PD-272 turntable and is very similar to the Micro Seiki TA-1 arm. This is in working shape and looks very good. Mounting distance on it is 225mm from pivot to spindle. Cables are made of Mogami microphone cable with Nakamichi RCA ends. Ground lead uses a Mueller, solid copper alligator clip. I’ve recently upgraded the tonearm on my main table so this is for sale - maybe you can use it. Please note: this is a vintage electronic item so sold as-is. This tonearm will be very well packed. Buyer pays $15 shipping. Ships to USA only. Thanks.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube. AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound. Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

Used for 1 year. Cable is in great condition.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube. AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound. Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube however the balance pot still seems to be a bit touchy where the left channel will go out. If one presses and/or wiggles it lightly the left channel will come back and often will stay on at length however if the balance or volume is bumped it will go out again then one must repeat the pressing/wiggling until it comes back on. It may in fact need a new pot or there is something else going out with how the volume and balance may interact as I notice a couple of wires that go behind the volume dial and Im not sure what that is for. Other than that slight glitch everything else including AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound.Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube however the balance pot still seems to be a bit touchy where the left channel will go out. If one presses and/or wiggles it lightly the left channel will come back and often will stay on at length however if the balance or volume is bumped it will go out again then one must repeat the pressing/wiggling until it comes back on. It may in fact need a new pot or there is something else going out with how the volume and balance may interact as I notice a couple of wires that go behind the volume dial and Im not sure what that is for. Other than that slight glitch everything else including AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound.Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube however the balance pot still seems to be a bit touchy where the left channel will go out. If one presses and/or wiggles it lightly the left channel will come back and often will stay on at length however if the balance or volume is bumped it will go out again then one must repeat the pressing/wiggling until it comes back on. It may in fact need a new pot or there is something else going out with how the volume and balance may interact as I notice a couple of wires that go behind the volume dial and Im not sure what that is for. Other than that slight glitch everything else including AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound.Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

Good condition vintage Nakamichi Receiver 2 made in Japan circa 1990. Similar yet better to the successor Nakamichi RE-2 receiver which came out in 1992. Ive thoroughly sprayed out all the potentiometers / buttons with CRC QD contact cleaner and lubricated them with DeoxIT F100L lube however the balance pot still seems to be a bit touchy where the left channel will go out. If one presses and/or wiggles it lightly the left channel will come back and often will stay on at length however if the balance or volume is bumped it will go out again then one must repeat the pressing/wiggling until it comes back on. It may in fact need a new pot or there is something else going out with how the volume and balance may interact as I notice a couple of wires that go behind the volume dial and Im not sure what that is for. Other than that slight glitch everything else including AM/FM, Phono, CD, Tape, Video works well and overall it has a superb sound.Radio memory presets functions flawlessly as I’ve replaced the Li-ion coin cell battery with a new one. No remote control included. Original manufacturer blurb: A receiver equipped with a unique harmonic time alignment amplifier. The amplifier section is designed using Nakamichis original harmonic time alignment theory. The Harmonic Time Alignment Theory was proposed by Steve Kalison, a former researcher at the Nakamichi America Research Center. The theory states that sound is good when the music signal and its harmonic distortion are aligned in time. This is related to the phenomenon that an amplifier with more distortion sometimes produces better sound than an amplifier with less distortion. The amplifier circuit used in the Receiver1 was developed based on this theory. It uses a wide-band, low-gain open loop design to keep the amount of NFB in the audio band constant. In addition, the amount of NFB itself is suppressed slightly, and a method to adjust the fundamental sound and distortion components correctly in time is applied. In addition, it is equipped with a power amplifier with excellent current supply capability to support low-impedance speakers. The power supply section employs a multi-regulated power supply system that independently regulates each stage of the amplifier, tuner section, display circuit, and logic circuit to prevent interference between sections. The ground circuit also uses a unique isolated ground system to shut out interference noise around the ground line. The tone control circuit uses a circuit that can adjust both ends of the frequency band without changing the characteristics of the middle band.This circuit can be lost. A quartz-lock synthesizer is used for the tuner section. This circuit uses a multiplex stage with a precision ceramic oscillator to ensure high selectivity, and an RF amplifier with a low-noise dual-gate MOS FET to provide high sensitivity and excellent reception performance that is robust against overloads. In addition, an isolation buffer is provided at the tuner output stage to prevent adverse effects of high-frequency noise on the audio signal. FM/AM10-station preset memories are installed. A motor-driven volume is used to prevent the deterioration of sound quality that occurs with electronic volume, while enabling volume adjustment by remote control. Equipped with variable loudness control. Built-in pre-out / main in terminal. Equipped with high-speed protection circuit. Equipped with an independent output selector for playback and recording.

...FROM A SMOKE FREE HOME SEE ALL REVIEWS ABOVE WHAT HI-FI BUMPER THICK EDITION HI-FI HAVE A LOOK ABOVE SO MANY REVIEWS WHAT HI-FI AMPLIFIER FROM PROTON AM445PRO - H KARDON HK6300 - ARCAM DELTA 60 - ALPHASON APOLLO - QED A270CD - ROTEL RA -870BX - WHAT HI-FI PROTON - H KARDON - ARCAM - ALPHASON - ROTEL - QED NAKAMICHI

Nakamichi Scart To 2x BNC Male And 2x RCA Male Phono Cable Adapter Wire Please note item has been used and has marks upon it please note item does have light marks and scratches upon it item has not been tested

Nakamichi AV-500 Replacement Part - RCA JACKS 4148259131 Ask all questions before purchase

Nakamichi AV-500 Replacement Part - RCA JACKS 4148259131 Ask all questions before purchase

36 pcs RCA Nakamichi Plug Audio Cable Male Connector Adapter Gold Plated. Please review the pictures since they are part of the description. New no box, not in original packaging.

Nakamichi Cinch-Kabel 1 Paar ca. 1m LängeGebrauchtes Paar Cinch-Kabel für Kassetten-/Tapedecksin sehr gutem, voll funktionsfähigem Zustand.

Nakamichi Cinch-Kabel 1 Paar ca. 1m LängeGebrauchtes Paar Cinch-Kabel für Kassetten-/Tapedecksin sehr gutem, voll funktionsfähigem Zustand.