Unit was acquired as surplus from a location doing a sound system overhaul. Unit powers on with no missing buttons/knobs. This isn’t the style of tech we typically deal in, as such no in depth testing has been performed. Unit was powered on & that is all. As such the unit is being sold AS-IS in untested condition for “Parts or Repair”

I have upgraded the Output Transistors in this 3225PE to take full advantage of the 80V PE Power rails without fear of damage. The original transistors are rated to only 60V, while the new Toshiba C5200/A1943 pairs are rated to 230V and recommended for 100W Power Amps. These same pairs are used in the NAD C series amplifiers. This 3225PE has all electronic muting for use with a master power strip, a smart AC Power switch, etc. A new power cord has been installed, and Ive replaced the Bias/Offset trimmers with multi-turn equivalents for more accurate and stable adjustments. I also installed an additional Heatsink on the Q508 Preamp Negative Rail regulator because it otherwise runs too hot for my fingers. The audio caps have been upgraded to WIMA Film at the Phono Input, Vishay Film in the Bass Control Filter, and nichicon MUSE, FW/Fine Gold, and ELNA Bipolar electrolytics elsewhere. The new Power Supply caps are nichicon, ELNA, and Panasonic. The new Main Caps are Chemicon KMQ 105C. There is a chipped corner and a nasty smudge on the front panel where a label used to be, and another label taped to the left side of the top cover. A license number has also been engraved on the top. Otherwise, this unit is in good condition. Please see photos. I will include a suitable NAD Label to cover the front panel smudge on request. Full refund within 60 days. Buyer pays return shipping. Please message me with any questions, corrections, etc. ******* The NAD 3225PE is a combination of the original 3020A all-discrete amplifier design and an enhanced Power Envelope supply that increases the output power to 25 WPC RMS and 60 WPC IHF. Unfortunately, the PE Supply is also capable of driving the original output transistors beyond their safe area, causing them to fail, which most likely happened to this unit. Ive lost count of how many Ive replaced. The new Toshibas can easily handle the PE Rails and beyond.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

NAD 3225PE Integrated Amplifier DescriptionUp for Sale is a NAD 3225PE Integrated Amplifier POWER ENVELOPE ~ POWERS ON ~ NO FURTHER TESTING so sold as Parts/Repair Condition.. it may work just fine. See photos for more details and item conditions. Items may exhibit minor cosmetic defects, including scuffs, marks, minor label residue from cleaning non-manufacturer labels off, or other minor defects.ShippingWe ship within 5 business of payment, ETD depends on courier processing We usually ship FedEx or USPS depending on item size & weight ReturnsNO RETURNS ~ MOST SALES FINAL PLEASE CONTACT US WITH QUESTIONS & INQUIRIESFeedbackIf you have any problems with the order, contact us we will do our best to fix the problem.Please do not leave a negative feedback without giving us the opportunity to solve the problem first.Feedback will be much appreciated, we will leave a feedback right back.ContactIf you have any queries, please contact us via ebay.

NAD 3225PE Integrated Amplifier DescriptionUp for Sale is a NAD 3225PE Integrated Amplifier POWER ENVELOPE ~ POWERS ON ~ NO FURTHER TESTING so sold as Parts/Repair Condition.. it may work just fine. See photos for more details and item conditions. Items may exhibit minor cosmetic defects, including scuffs, marks, minor label residue from cleaning non-manufacturer labels off, or other minor defects.ShippingWe ship within 5 business of payment, ETD depends on courier processing We usually ship FedEx or USPS depending on item size & weight ReturnsNO RETURNS ~ MOST SALES FINAL PLEASE CONTACT US WITH QUESTIONS & INQUIRIESFeedbackIf you have any problems with the order, contact us we will do our best to fix the problem.Please do not leave a negative feedback without giving us the opportunity to solve the problem first.Feedback will be much appreciated, we will leave a feedback right back.ContactIf you have any queries, please contact us via ebay.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

The NAD Integrated Amplifier 3225PE is a high-quality audio component that delivers exceptional sound performance. With 2x 40-Watt Channels, this amplifier provides powerful output and clear, detailed sound. The 3225PE is an excellent choice for music enthusiasts looking for a reliable amplifier that can handle a wide range of audio sources. This amplifier is designed with the latest technology and features a sleek, modern design that will complement any home audio system. The NAD 3225PE is a perfect choice for anyone who wants a high-quality amplifier that delivers exceptional sound performance. All products come with what you see in the pictures only. No other items are included if they are not in the pictures. All products are cleaned and sanitized prior to posting . We strive for excellent customer service and stand behind our products.

This is a service only listing to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3150, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Unique replacement parts like transformers or potentiometers may need to be purchased if required. 1) Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch (without low level poles) and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit more suitable for Remote Power switching with Intelligent Power Strips, etc. 2) Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. 3) Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. and WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. 4) Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This Nad 3220PE Stereo Integrated Amplifier is a gem for any music lover. With its sleek design and high-quality sound, its sure to enhance your listening experience. The brand, NAD, is known for producing top-of-the-line audio equipment, and this amplifier is no exception. The model is available in various types, making it customizable to your specific needs. The amplifier is in mint condition and comes in its original box, ready to be used right out of the package. Whether youre a music enthusiast or simply looking to upgrade your home audio system, this Nad 3220PE Stereo Integrated Amplifier is the perfect addition.

This is a service only listing for any parts I already have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Replace Power Switch and Upgrade Muting circuit - Experience has shown that the power switch is almost always worn out. The exact replacement is up to $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch and I modify the muting to be all electronic like the 3225PE and 701. This makes the unit suitable for use with Intelligent Power Strips, etc. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. or WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. Realign Power Amps for 0mV Offset and specified Bias. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This is a service only listing for any parts I already have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3130, 3220PE, 3225PE, 302, and 312. The shipping charge is for the return trip in the same packaging you sent. Replace Power Switch and Upgrade Muting circuit. Experience has shown that the power switch is almost always worn out. The exact replacement now costs $50 due to the special low level poles used for ON/OFF muting. Instead, I now use a higher rated, lower cost power switch and upgrade the muting to be all electronic, just like the 3225PE and 701. This makes the unit suitable for use with Intelligent Power Strips, etc. Note that I have raised the price $24 to include this service instead of asking for an additional $35 after the fact. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace all Electrolytic Capacitors. Ill upgrade the audio coupling caps with Bipolar nichicon, ELNA, etc. or WIMA, Vishay Film. I typically choose 105C and/or higher voltage rated caps for the power supplies. I can also install capacitors that you provide as desired. Upgrade the Bias and Offset trimmers to multi-turn equivalents for more precise and stable adjustments. Realign Power Amps for 0mV Offset and specified Bias. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or otherwise) that youd like to Buy and have serviced, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

NAD Integrated Amplifier 3225PE 2x 40-Watt Channels - WORKS. Condition is Used. Shipped with UPS Ground.

NAD 3225 Integrated Amplfier Service Manual *Original*.

Nad 3220PE Stereo Integrated Amplifier - Excellent Condition. Very good condition. Tested and reviewed. See pictures for details and bid accordingly. 30 day warranty Specifications Power output: 25 watts per channel into 8? (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.05% Input sensitivity: 2.5mV (MM), 200mV (line) Signal to noise ratio: 76dB (MM), 85dB (line) Speaker load impedance: 4? (minimum) Dimensions: 420 x 80 x 250mm Weight: 5kg Year: 1987 Thank you for shopping Renewed Hearts

This is a service only listing for any parts I have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace the Electrolytic Capacitors in the Power Supplies, Amplifier sections, and Tuner Audio sections. Ill upgrade the audio caps with nichicon, ELNA, Rubycon, and Panasonic audio grades while preferring 105C and/or higher voltage rated caps for the power supplies. I can also install any capacitors that you provide as desired. Note that replacing the power switch is an additional $35. If you hear a sizzling sound as you slowly push it on or off, then its time to replace it. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or Otherwise) that youd like to Buy and have repaired and/or recapped, then perhaps you can save on shipping by having it sent directly to me. Please message me first.

This is a diagnostic only listing for an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models.

BUY WITH CONFIDENCE: PROFESSIONAL SELLER WITH 99%+ POSITIVE CUSTOMER FEEDBACK FROM OVER 9900 ORDERS NAD 3225PE STEREO INTEGRATED AMPLIFIER 1990s PHONO OUTPUT SERVICED WORKS WELL SERVICED, TESTED & WORKS WELL. VERY GOOD OVERALL CONDITION – SOME MARKS, NICKS & SCRATCHES IN LINE WITH AGE & USE – PARTICULARLY AT THE TOP - PLEASE STUDY PHOTOS TO ASSESS CONDITION YOURSELF. DIGITAL OPERATING MANUAL AVAILABLE. FURTHER PRODUCT INFORMATION / SPECIFICATION BELOW: *BUY WITH CONFIDENCE - PROFESSIONAL FIRST-RATE SELLER WITH 99%+ POSITIVE CUSTOMER FEEDBACK* SHIPPING AVAILABLE VIA REPUTABLE COURIERS SUCH AS FEDEX, DX & UPS - WITH TRACKING & INSURANCE PRICE QUOTED FOR UK MAINLAND ONLY COLLECTION FROM TWICKENHAM, SOUTH WEST LONDON, TW2 6RN INTERNATIONAL SHIPPING VIA EBAY’S GLOBAL SHIPPING PROGRAMME (GSP) THE SMALL PRINT Save money - remember we can combine shipping costs for multiple items. From a pet and smoke-free home. Carefully packaged. Thanks for visiting & please contact me if you have any questions, Paul FURTHER PRODUCT INFORMATION / SPECIFICATION Power output: 25 watts per channel into 8? (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.03% Damping factor: 40 Input sensitivity: 2.5mV (MM), 160mV (line) Signal to noise ratio: 75dB (MM), 101dB (line) Dimensions: 420 x 80 x 250mm Weight: 5kg Year: 1991

This is a service only listing for any parts I have plus the labor required to Restore and Re Cap an NAD 3020 or similar 3020_like amplifier that YOU send to me including the 3020A, 3020B, 3020i, 3020e, 3220PE, 3225PE, 302, 312 and Receivers including the 7020i, 7020e, 7220PE, 7225PE, and 701. The shipping charge is for the return trip back to you in the same box sent. Restore - Clean and inspect the inside of the unit. Repair any issues discovered or mentioned by the buyer. Deoxit switches and potentiometers. Resolder RCA, DIN, and Headphone jacks as needed to reseat and resecure them, along with any other questionable solder joints. Re Cap - Replace the Electrolytic Capacitors in the Power Supplies, Amplifier sections, and Tuner Audio sections. Ill upgrade the audio caps with nichicon, ELNA, Rubycon, and Panasonic audio grades while preferring 105C and/or higher voltage rated caps for the power supplies. I can also install any capacitors that you provide as desired. Note that replacing the power switch is an additional $35. If you hear a sizzling sound as you slowly push it on or off, then its time to replace it. International units at 220VAC are no problem. Please allow 7-10 days from receipt to return ship so that I have time to listen and confirm proper operation. The 30 day handling time is intended to include your ship time to me as well. Feel free to message me with any questions or to inquire about the repair and/or recap of other models. If you see a Preamp, Integrated Amp or Power Amplifier on eBay (for Parts / Not Working or Otherwise) that youd like to Buy and have repaired and/or recapped, then perhaps you can save on shipping by having it sent directly to me. Please message me first.