I bought this CD player new. Over the years it has had more and more trouble recognizing CDs. Now it only rarely recognizes a CD when you put one in. When it does recognize the CD it plays it perfectly. This is still a great sounding CD player. The problem is clearly in the laser mechanism. There are replacements available on eBay and elsewhere for $25-50. If you can do the work, or have someone who can do it youll have a great CD player for much less than its worth. If you have a beat up player, you can swap mechanisms and have a great condition player. The condition is near new, without scratches or other defects. Everything that came with it new is included, remote, power cord, instructions, box, and packing materials.

Triple stack, consisting of the DAC, the Tube Buffer and the power supply for both. With the two power supply cables from the power supply to each active unit - one for the Dac, and one for the tube buffer. thoughtfully re-capped with premium and nonmagnetic film caps (the big blue ones), and opamps socketed for easier upgrading. All while referencing the tech manuals for the chips involved, of course. Tube buffer also mildly modded with newer output caps w/non-magnetic polypropylene bypass caps Works beautifully.

Musical fidelity X-Can V3 headphone amplifier in perfect cosmetic and working order. Original packaging for amp is not included but I will cushion it well. Any questions just ask.

MUSICAL FIDELITYX-DAC-V3 AND X-PSU-V3 COMBO UPGRADED COMPONENTS THIS X-DAC AND POWER SUPPLY COMBO HAS SEEN MINIMAL USE OVER THE YEARS. KEPT AS A SPARE, IT WAS RARELY INSTALLED IN A SYSTEM. COSMETICS ARE EXCELLENT. NO OBVIOUS FLAWS ON THE DAC. THE X-PSU POWER SUPPLY HAS A SMALL FLAW AT THE REAR CORNER ON ONE FIN.....WHICH I BELIEVE WAS A FACTORY DEFECT. ITS ONLY VISIBLE FROM THE REAR. THE X-PSU-V3 POWER SUPPLY IS ORIGINAL AND UNMOLESTED. ITS JUST AN OVERSIZE TRANSFORMER THAT ALLOWS YOU TO CONNECT OTHER V3 COMPONENTS INTO ONE POWER SUPPLY. I FELT IT DID PERFORM BEST WHEN ONLY 2 COMPONENTS MAXIMUM WERE CONNECTED.3 POWER CONNECTOR CORDS FOR ADDITIONAL UNITS ARE INCLUDED. ONE CORD IS MISSING AND HAS DISAPPEARED. A NEW AC POWER CARD IS INCLUDED. THE X-DAC-V3 HAS HAD SIGNIFICANT COMPONENT UPGRADES. THESE MODS WERE INSPIRED BY AN ARTICLE ON THE BURSON AUDIO WEBSITE BACK WHEN THEY FIRST INTRODUCED (HDAM) DISCRETE OP-AMPS, A NUMBER OF YEARS AGO. SOME UPGRADES WERE TAKEN FROM THE ARTICLE. OTHER UPGRADES WERE MINE. THE DAC POWER SUPPLY CAPACITANCE WAS VASTLY INCREASED USING NICHICON MUSE AUDIO GRADE CAPS. CARE WAS TAKEN TO INSURE THE (STACK OF) CAPS WERE SOLIDLY MOUNTED TO REDUCE/ELIMINATE ANY VIBRATIONAL EFFECT. THE STANDARD BRIDGE RECTIFIER WAS REPLACED WITH INDIVIDUAL HYPER-FAST/SOFT RECOVERY DIODES. ALL OTHER ELECTROLYTIC CAPACITORS WERE REPLACED WITH SANYO OS-CON POLYMER AND ELNA SILMIC II AS THE APPLICATION REQUIRED. NON-POLAR CAPS WERE REPLACED WITH (A LARGE NUMBER OF) WIMA POLYPROPYLENE FILM AND OTHER POLYPROPYLENE FILM CAPS. POLYPROPYLENE BY-PASS CAPACITORS WERE ADDITIONALLY INSTALLED UNDERNEATH THE CIRCUIT BOARD AS NEEDED. AT THE ANALOG OUTPUT, THE 2 ELECTROLYTIC NON-POLAR CAPS WERE REPLACED WITH NICHICON MUSE, BY-PASSED WITH POLYPROPYLENE FILM/FOIL CAPACITORS. THE RCA OUTPUT JACKS ARE CONNECTED WITH SHIELDED SILVER PLATED WIRING. HEATSINKS WERE INSTALLED ON SURFACE MOUNTED ICS AND MICRO PROCESSORS. LASTLY, I DID INSTALL SOME BURSON DISCRETE OP-AMPS, BUT LATER REMOVED THEM. WHILE THE OP-AMPS DID SLIGHTLY ALTER THE SOUND, I COULD NOT DEFINITIVELY STATE THERE WAS AN ACTUAL IMPROVEMENT AND WORTH THE ADDITIONAL COST IN THIS APPLICATION. THE VAST MAJORITY OF AUDIBLE SOUND/PERFORMANCE IMPROVEMENTS CAME FROM THE COMPONENT UPGRADES THAT WERE COMPLETED FIRST. NOT THE INSTALLATION OF THE DISCRETE OP-AMPS, THAT WERE INSTALLED LAST. THE ORIGINAL 5532 OP-AMPS ARE INSTALLED IN SOCKETS AND CAN BE EASILY REPLACED IF, SHOULD THE BUYER WANT TO EXPERIMENT WITH OTHER OP-AMPS/HDAMS. THIS UPGRADED V3-DAC AND POWER SUPPLY COMBO PROVIDES A SMOOTH ANALOG SOUND THAT RIVALS NEWER, OR MORE EXPENSIVE DACS.

Biete hier eine Musical Fidelity Verstärker/CD Kombi in Bestzustand an.Die Geräte der X Serie sind ja für ihren fantastischen Klang hinlänglich bekannt. Die Geräte weisen faktisch keinerlei Gebrauchsspuren auf und sind technisch voll funktionsfähig.Die originale Fernbedienung welche beide Geräte steuert ist ebenfalls vorhanden.Wer auf der Suche nach einer kompakten, highendig klingenden Anlage ist, ist hier genau richtig. Der Verkauf erfolgt nur, da ich auf eine aktive Lösung umgestiegen bin. Für den CD Player ist noch die Originalverpackung vorhanden.Der Versand erfolgt in einem Karton. Versand mit DHL € 19,99Versand nach China mit DHL € 100,99 Da die neue EU-RICHTLINIE jetzt 1 Jahr Gewährleistung auch für Privatverkäufe vorsieht - soweit der Verkäufer es nicht ausschließt - erkläre ich, dass ich für meine privat verkauften Artikel keine Gewährleistung im Sinne der EU-Richtlinie übernehme. Mit Kauf der Ware erklären Sie sich ausdrücklich damit einverstanden, auf die Garantie / Gewährleistung zu verzichten. Auf die bei mir gekauften gebrauchten Artikel, besteht keinerlei Widerrufs- und Rückgaberecht (§312dAbs.4Nr.5BGB)

Musical Fidelity X10 V3 Röhrenbuffer / Röhrenpuffer rar & limitiert Neu aus Nachlass. Nr. 335 von 4800 jemals gebauten Exemplaren weltweit. Es gab nicht mehr Röhrensätze. Vermutlich unbenutzt (Netzteil war noch eingeschweißt) aus dem Nachlass meines Schwiegervaters. Er mußte jeden heißen Scheiß haben! In dem Zustand vermutlicht nirgendwo zu bekommen. Die Militärröhren sind auf 100000 Betriebsstunden ausgelegt. Privatverkauf ohne Rückgabe.Internationaler Versand gegen anderen Preis. ( für internationalen Verkauf will Ebay Deutschland dann doch Provision haben) möglich! siehe auch Rock Grotto und andere High-End Seiten Legendäre Röhrenpufferstufe von Musical Fidelity hier in der V3 Version. Die X-10 wird zwischen CD-Player und Verstärker eingeschleift und kann den Digitalklang älterer CD-Spieler deutlich verbessern. Ebenso zwischen Transitor Vorstufe und Endstufe. Oder hinter digital DAC. Guter Zustand mit nur geringen Gebrauchsspuren. -Externe Stromversorgung -Jamicon-Kondensatoren, 8 Hauptkondensatoren haben eine Gesamtkapazität von 6940µF - Röhrenstufe mit 2 Philips ECG USA Röhren Mu-Vista About the Mu-Vista tube:Musical Fidelity’s latest discovery, the 6112, is an ultra high performance twin triode that we call the mu-Vista. Originally, it was used by the US military for crucial low noise guidance and other missile functions. It is incredibly rugged and immune from microphony and other extraneous effects. Also, and we hope this attribute is never needed; it’s immune from electro-magnetic pulse (EMP) which occurs when a nuclear bomb explodes! As you would expect, the mu-Vista is super tough, super quiet, ultra reliable, incredibly linear and absolutely predictable.Musical Fidelity has not had a single Tri-Vistor 5703 tube fail anywhere in the world in any of their Tri-Vista products. Our tests show that the mu-Vista has similar levels of reliability, and why not? The tubes have been purchased direct from the US military and are genuine milspec, mil usage parts.As far as we know, they have bought the vast majority of the world’s stock of the amazing mu-Vista. It will form the basis of a number of limited edition products. Tube buffer Musical Fidelity X-10v3. Introduced for the first time in year 2004. Successor of the more popular X-10D. Connecting it, in between the source (ex. CD player) and the amplifier, makes the sound more tube-like. Using it between pre- / power amp solves the problem of impedance mismatch, if you suffer one. Loop output makes it possible to directly compare the sound with / without the buffer. Very nice feature, enjoyed playing with it. Furthermore, typical MF, simple but well finished casework. Solid chassis, fully made out of metal, plus a thick, brushed aluminum face plate. Limited gear, only 4800 ever produced;External power supply – no transformer inside the case;Jamicon capacitors, 8 main ones have the total capacity of 6940µF;Tube output stage on 2 Philips ECG USA tubes (muVista).

Musical Fidelity X-ray V3 24 Bit CD player in good working condition. Comes with remote control and power cord. There are a few minor chips on cosmetic.

Musical Fidelity X10 V3 Röhrenbuffer / Röhrenpuffer rar & limitiert Neu aus Nachlass. Nr. 335 von 4800 jemals gebauten Exemplaren weltweit. Es gab nicht mehr Röhrensätze. Vermutlich unbenutzt (Netzteil war noch eingeschweißt) aus dem Nachlass meines Schwiegervaters. Er mußte jeden heißen Scheiß haben! In dem Zustand vermutlicht nirgendwo zu bekommen. Die Militärröhren sind auf 100000 Betriebsstunden ausgelegt. Privatverkauf ohne Rückgabe.Internationaler Versand gegen anderen Preis. ( für internationalen Verkauf will Ebay Deutschland dann doch Provision haben) möglich! siehe auch Rock Grotto und andere High-End Seiten Legendäre Röhrenpufferstufe von Musical Fidelity hier in der V3 Version. Die X-10 wird zwischen CD-Player und Verstärker eingeschleift und kann den Digitalklang älterer CD-Spieler deutlich verbessern. Ebenso zwischen Transitor Vorstufe und Endstufe. Oder hinter digital DAC. Guter Zustand mit nur geringen Gebrauchsspuren. -Externe Stromversorgung -Jamicon-Kondensatoren, 8 Hauptkondensatoren haben eine Gesamtkapazität von 6940µF - Röhrenstufe mit 2 Philips ECG USA Röhren Tube buffer Musical Fidelity X-10v3. Introduced for the first time in year 2004. Successor of the more popular X-10D. Connecting it, in between the source (ex. CD player) and the amplifier, makes the sound more tube-like. Using it between pre- / power amp solves the problem of impedance mismatch, if you suffer one. Loop output makes it possible to directly compare the sound with / without the buffer. Very nice feature, enjoyed playing with it. Furthermore, typical MF, simple but well finished casework. Solid chassis, fully made out of metal, plus a thick, brushed aluminum face plate. Limited gear, only 4800 ever produced;External power supply – no transformer inside the case;Jamicon capacitors, 8 main ones have the total capacity of 6940µF;Tube output stage on 2 Philips ECG USA tubes (muVista).

Musical Fidelity X10 V3 Röhrenbuffer / Röhrenpuffer rar & limitiert Neu aus Nachlass. Nr. 335 von 4800 jemals gebauten Exemplaren weltweit. Es gab nicht mehr Röhrensätze. Vermutlich unbenutzt (Netzteil war noch eingeschweißt) aus dem Nachlass meines Schwiegervaters. Er mußte jeden heißen Scheiß haben! In dem Zustand vermutlicht nirgendwo zu bekommen. Die Militärröhren sind auf 100000 Betriebsstunden ausgelegt. Privatverkauf ohne Rückgabe.Internationaler Versand gegen anderen Preis. ( für internationalen Verkauf will Ebay Deutschland dann doch Provision haben) möglich! siehe auch Rock Grotto und andere High-End Seiten Legendäre Röhrenpufferstufe von Musical Fidelity hier in der V3 Version. Die X-10 wird zwischen CD-Player und Verstärker eingeschleift und kann den Digitalklang älterer CD-Spieler deutlich verbessern. Ebenso zwischen Transitor Vorstufe und Endstufe. Oder hinter digital DAC. Guter Zustand mit nur geringen Gebrauchsspuren. -Externe Stromversorgung -Jamicon-Kondensatoren, 8 Hauptkondensatoren haben eine Gesamtkapazität von 6940µF - Röhrenstufe mit 2 Philips ECG USA Röhren Tube buffer Musical Fidelity X-10v3. Introduced for the first time in year 2004. Successor of the more popular X-10D. Connecting it, in between the source (ex. CD player) and the amplifier, makes the sound more tube-like. Using it between pre- / power amp solves the problem of impedance mismatch, if you suffer one. Loop output makes it possible to directly compare the sound with / without the buffer. Very nice feature, enjoyed playing with it. Furthermore, typical MF, simple but well finished casework. Solid chassis, fully made out of metal, plus a thick, brushed aluminum face plate. Limited gear, only 4800 ever produced;External power supply – no transformer inside the case;Jamicon capacitors, 8 main ones have the total capacity of 6940µF;Tube output stage on 2 Philips ECG USA tubes (muVista).

Musical Fidelity X-LPS V3 MM/MC Phono Stage, good condition, 3 month warranty Musical Fidelity X-LPS V3 MM/MC Phono Stage, good condition, 3 month warranty A fine X-LPS V3 MM/MC Phonostage from Musical Fidelity – housed in the slightly smaller than half width case. It is in good condition with a couple of minor blemishes on the fascia – please see photographs – comes in original factory packaging with power supply unit and our normal three month warranty. Please note the PSU is an after-market upgrade of unknown origin and although tested and working will not be covered in our warranty. Specifications: MM Input: Sensitivity: 3mV for 350mV output at 1kHz Input Impedance: 47K Ohms THD: < 0.01% at 1kHz, 350mV out Input Overload Margin: 30dB S/N Ratio: > 75dB unweighted; > 83dB “A” weighted MC Input: Sensitivity: 350µV for 350mV output at 1kHz Input Impedance: 100 Ohms THD: < 0.01% at 1kHz, 350mV out Input Overload Margin: 30dB S/N Ratio: > 65dB unweighted > 74dB “A” weighted General: RIAA Accuracy: ±0.25dB 20Hz to 20kHz Power Requirement: 12-0-12Volts AC 500mA (via mains adaptor supplied) Dimensions: 180 (W) x 208 (D) x 88.2 (H) mm Weights: 2.5 kg ; Adaptor: 0.45kg Manufacturer : Musical Fidelity Model : X-LPS V3 Serial Number : XLG0086 Packaging : Original Accessories Included : PSU / DIN / Manual / Mains Cable Price When New :  Shipping Shipping cost:Please contact us or check listing info. If you are outside the UK you will need a shipping quote BEFORE buying. Delivery time:48 hours Payment We accept the following payment methods: Paypal Credit/Debit Card BACS Please contact us if you have any questions. Service Established in 2003, 2ndhandhifi is the UKs largest stockist of used quality audio equipment. All items are checked before despatch and guaranteed for 30 days for ebay buyers to give you peace of mind that the item will arrive safely and work exactly as per ebay descriiptions. This means that all items described as used will be in good working order but may show minimal cosmetic marks resulting from everyday use. Any more significant cosmetic issues will be highlighted in the listing if present. We accept most payment methods but card payment to our shop is preferred. We use a reputable overnight courier service - items will be despatched next working day for delivery the next working day after that, but you are welcome to collect from our sister shop in Stockton on Tees if you prefer. Check our feedback if you have any doubts about the validity of this auction or us! We are a business so (although most times we do) we cannot always answer emails over the weekend so please try to ask Monday to Friday. Important 1. If there is no buy it now price stated, please dont ask - it is intended to be an auction which will run until its end time. 2. If you are outside the UK mainland please ask us for a shipping quote BEFORE placing a bid or clicking “Buy it Now”. If you dont ask, it means you will accept our quote. We do not cut corners on shipping, we only use reliable shipping companies, and we dont profit from the shipping prices we quote. 3. For any item where there is no original packaging the shipping costs include the cost to package the item to ensure safe delivery. Larger items may be shipped on a pallet - but this usually will be stated in the listing. 4. If you win the auction or buy the item, we expect you to pay and we will issue a non payment against you if you dont. Such auctions/listings cost us time (and therefore money). Requests to cancel will be rejected.

Musical Fidelity X10 V3 Röhrenbuffer / Röhrenpuffer rar & limitiert Neu aus Nachlass. Nr. 335 von 4800 jemals gebauten Exemplaren weltweit. Es gab nicht mehr Röhrensätze. Vermutlich unbenutzt (Netzteil war noch eingeschweißt) aus dem Nachlass meines Schwiegervaters. Er mußte jeden heißen Scheiß haben! In dem Zustand vermutlicht nirgendwo zu bekommen. Die Militärröhren sind auf 100000 Betriebsstunden ausgelegt. Privatverkauf ohne Rückgabe.Internationaler Versand gegen anderen Preis. ( für internationalen Verkauf will Ebay Deutschland dann doch Provision haben) möglich! siehe auch Rock Grotto und andere High-End Seiten Legendäre Röhrenpufferstufe von Musical Fidelity hier in der V3 Version. Die X-10 wird zwischen CD-Player und Verstärker eingeschleift und kann den Digitalklang älterer CD-Spieler deutlich verbessern. Ebenso zwischen Transitor Vorstufe und Endstufe. Oder hinter digital DAC. Guter Zustand mit nur geringen Gebrauchsspuren. -Externe Stromversorgung -Jamicon-Kondensatoren, 8 Hauptkondensatoren haben eine Gesamtkapazität von 6940µF - Röhrenstufe mit 2 Philips ECG USA Röhren Tube buffer Musical Fidelity X-10v3. Introduced for the first time in year 2004. Successor of the more popular X-10D. Connecting it, in between the source (ex. CD player) and the amplifier, makes the sound more tube-like. Using it between pre- / power amp solves the problem of impedance mismatch, if you suffer one. Loop output makes it possible to directly compare the sound with / without the buffer. Very nice feature, enjoyed playing with it. Furthermore, typical MF, simple but well finished casework. Solid chassis, fully made out of metal, plus a thick, brushed aluminum face plate. Limited gear, only 4800 ever produced;External power supply – no transformer inside the case;Jamicon capacitors, 8 main ones have the total capacity of 6940µF;Tube output stage on 2 Philips ECG USA tubes (muVista).

Musical Fidelity X-LPS V3 phono stage with upgraded power supply. Bought earlier this year. It didnt come with the original MF power supply, so eventually I bought one from AliExpress. This worked out very well, and I have used it with absolutely no issues at all. In the past few weeks I have bought a couple of other phono stages, both valve, and I have decided to keep these for the time being. I am also aiming to raise funds for a Yamaha GT-2000L turntable. I bought a Denon DP-59L a few months ago, and its superb. So Im now wondering how good the Yamaha is. I have only used the MM input on the MF, as I dont have an MC cartridge. The seller blurb on the power supply is as follows: 30W hi-end R-core transformer.Using Pure oxygen-free copper wire + high quality iron coreHi-end 16mm metal push button switchAC power supplyEMI filter suppression RFI noiseHigh quality parts (Japanese original Nichicon capacitors)

Here is a Musical Fidelity X-ray V3 24 Bit CD player with its original remote. Both the player and the remote are in immaculate, like new condition and function perfectly. Please see some specs. and part of a review below. Thanks for looking! Specifications Disc format: CD Digital converter: Delta Sigma, 24 bit, 8 x oversampling Frequency response: 10Hz to 20kHz Signal to Noise Ratio: 115dB Channel separation: 100dB Total harmonic distortion: 0.006% Line output: 2.14V Digital connections: coaxial, optical Dimensions: 216 x 100 x 345mm Weight: 5kg Accessories: remote control REVIEW Musical FidelitysAntony Michaelsonputs the X-Rayv3on a par or better than most of the worlds expensive CD players. Thats quite a statement for a player that retails for under $1000. I havent heard most of the worlds pricey players, and Im not sure what expensive is. I do know that Ive heard nothing better for under $1000. In fact, Im not sure Ive heard anything better for under $2000.

Welcome to bid for Premium Power Supply Unit for Musical Fidelity X Series Ver 3 and Ver 8DACs and Preamps with Valve Output This is high quality power developed especially for use with X series Version 3 and Version 8 family of audio gears from Musical Fidelity.The PSU provides highly stable and purified AC voltage output of 24 (12-0-12) volt, exactly as specified for the following devices from Musical fidelityX10D V3 Valve BufferX Cans V3X DAC V3 DacX LPS V3 Phono Stage Preamplifiersuitable for V8 models XLps V8 and XCans V8but not suitable for some V8 models, like X-Ray or X-plora - please ask if you are in doubt Please note that similar PSU to be used with Musical Fidelity Ver.1 and Ver 2 (AC 12 V) audio items likeX-10D valve bufferX-DACs (all models)X-PreampX-LP phono stageX-CAN headphone amplifiers - in it V1 and V2 editions. PRESENTED IN OUR PARALLEL AUCTION please have a look there or ask about suitability for your system if you are in doubt PSU presented in the auction capable built with very high audio grade 30W power toroidal transformer and has 3 times more output power that the original wall adaptor and improves sonic performance of the deviceslisted above as well as many other types where AC 24 Volt is power requirement.Please ask if you are in doubt relating suitability of this PSU with your particular item. The PSU is assembled in solid aluminium frame matched aestetically with X series from Musical Fidelity.This is not an universal power supply adopted for audio gears, but dedicated and especially developed for use with Musical Fidelity X series V3 power source.In particular, not just output voltage is matched, but output impedance and regulation characteristics are tuned optimal for the best sonic results when paired with Musical Fidelity audio equipment.We show connection of this PSU to X10D V3 in few pictures as example of use, but this the X10 is not included and shown for illustration onlyMains cable is not normally included, but please let us know if you need one to be sent with the psu, we will supply it. Delivery and possible return.This player will be supplied with replacement remote control,. Shipping cost of £10 quoted is related to UK mainland destinations only and includes insurance. Could be shipped any other location worldwide, but, please, ask for quotation before bidding if you are outside the UK mainland. We combine shipments, just ask if you buy more than one item. In particular, any cable presented in our auctions, if purchased, will be sent with this item without extra postage. Please, note that we ship in 5 days after he payment is cleared, please allow some extra time for delivery. Attention of International bidders: we will be pleased to ship worldwide. Shipping cost of £19 quoted is initial estimation for EU only.Overseas delivery could cost from £36 (USA, China) to £30(Australia, South America) We charge an actual minimal for international shipment, please, ask for quotation before bidding to be sure. Please, note that overseas delivery can take up to 12 working days. Unfortunately we can not ship to Vietnam and Ukraine. Item is fully tested and return is accepted within 2 week after delivery and exclusively in shape as it was shipped, i.e. perfect working condition. In this case 100% of auction price and shipment cost will be refunded. Return of nonworking, damaged or scratched item is not accepted and will be not refunded. Return shipment cost is on Buyer’s side.

Normal 0 false false false EN-GB X-NONE X-NONE Musical Fidelity X-Ray V3 24-Bit CD Player Musical Fidelity X-Ray V3 comes with official remote and power lead. In very good used condition with surface scratches and small marks. In full working order. Specifications Disc format: CD Digital converter: Delta Sigma, 24 bit, 8 x oversampling Frequency response: 10Hz to 20kHz Signal to Noise Ratio: 115dB Channel separation: 100dB Total harmonic distortion: 0.006% Line output: 2.14V Digital connections: coaxial, optical Dimensions: 216 x 100 x 345mm Weight: 5kg Please check all of the photographs as these helps to form part of the description. If you require any help with your order, please don’t hesitate to contact us by eBay contact form.