Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Monitor Audio Gold 300 5G Piano Ebony, Brand new, EX-DEMO. Speakers are from our showroom. They were connected for less than 10 hours.

Polk Audio RM3000 Monitor Series 2 Speakers, Speckled Stone Color Used. Good condition. One speaker has a tear and there are a few small tears in the speaker covers. Speakers are very heavy. Old school quality.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

MONITOR AUDIO SILVER 300 6G FLOOR STANDING SPEAKERS (PAIR) SATIN WHITE. Tested to be fully functional. Besides some light scuffs / scratches which can barely be seen the pictures, these pair of speakers are in great condition. Speaker and Speaker grill cover only no other accessories. These will be packaged securely and signature required for safe delivery. See detailed pictures.  The Monitor Audio Silver 300 floorstander retains the familiar award-winning configuration of its predecessor, with several crucial improvements to drivers. The full three-way design delivers class-leading mid-range, while a pair of long-throw 6-inch bass drivers work together to produce incredible power from the tall, but slim cabinet design, making it the perfect choice for serious audiophile and AV installations.The three-way configuration allows each driver to be optimized to do a better job over a narrower frequency band; the only real way to deliver elevated performance in every respect. Superlatively natural mid-range comes courtesy of a dedicated 4-inch driver, specially designed with ‘under hung’ voice coil and motor system. This technique ensures the voice coil always remains in the magnetic gap under all conditions for demonstrably lower distortion than usually found at this level – an advance which can be immediately heard. TO PREVENT FRAUDSPECIALLY MARKED OR SERIAL # RECORDED PLEASE DONT ASK US TO SHIP TO A DIFFERENT ADDRESS OTHER THAN THE ONE PROVIDED BY EBAY PLEASE UPDATE YOUR SHIPPING ADDRESS BEFORE CHECKOUT THANKS.WARRANTY: WE WILL WARRANTY THE UNIT FREE FROM DEFECTS AS STATED IN THE LISTING DESCRIPTION. ABUSE AND ACCIDENTAL DAMAGE DO NOT QUALIFY FOR WARRANTY COVERAGE. BUYER IS RESPONSIBLE FOR ALL SHIPPING COSTS FOR ANY WARRANTY CLAIMS. WARRANTY START DATE DETERMINED BY DELIVERY DATE AS RECORDED BY YOUR TRACKING NUMBER. CHIPSET, CPU & BOARD SERIAL NUMBERS RECORDED FOR WARRANTY PURPOSES.REFUND POLICY: UNLESS OTHERWISE INDICATED IN THE TERMS OF THE LISTING WE ARE HAPPY TO REFUND YOU UPON RETURN OF THE ORIGINAL ITEM IN ITS ORIGINAL CONDITION AS SENT TO YOU WITHIN 30 DAYS ONLY IF ITEM IS NOT AS DESCRIBED. THIS DETERMINED BY THE DAY YOU RECEIVED THE ITEM BASED ON THE INFORMATION PROVIDED BY THE TRACKING NUMBER. NO REFUNDS AFTER 30 DAYS.IF THE ITEM COMES BACK TO US IN THE DESCRIBED CONDITION AND FUNCTIONAL THEN THERE WILL BE 20% RESTOCKING FEE. Listing and template services provided by inkFrog

A pair of Polk Audio MM691s. These are generally used for car audio as 6x9 replacement speakers. These have never been used. Purchased for a car long ago and have sat safely in storage for many years. The box is worn, but the components inside are unharmed. Item will be shipped in this box as is. Ill tape it well, though. From the manufacturer:Polk Audio continues its tradition of making brilliant-sounding speakers in stylishly designed packages — their Mobile Monitor (MM) Series speakers look great and sound even better. Each speaker utilizes an extra-strong, extra-small neodymium magnet that saves space and weight, allowing these speakers to fit into more places in more vehicles while still delivering a full sound with lots of kick. Their lightweight carbon composite frames provide strong, flex-free support for the speakers motor assemblies.The Polk MM691 6x9 speakers feature honeycomb-textured woven glass fiber composite woofer cones that respond very quickly for a clean, crisp, and powerful sound. Large voice coils — over an inch in diameter — give the speaker high power handling capability and extended reliability.3/4 and 1 silk dome tweeters add a sweet high end that blends perfectly with the low notes so your music stays in harmonic balance, from the electric bass all the way on up to the cymbals.Important Note: These Polk speakers use a low-impedance design to pull more power safely from your car stereo or amplifier. This design is compatible with virtually all factory and aftermarket stereos.Priced per pairREAD LESSProduct highlights:6x9 3-way speakers (pair)woven honeycomb glass fiber composite woofer cone with butyl rubber surround1 and 3/4 silk composite dome tweeterscertified for marine use2.7-ohm impedance for extra power (compatible with virtually all factory or aftermarket car stereos)power range: 15-125 watts RMS (300 watts peak power)frequency response: 30-25,000 Hzsensitivity: 94 dB @ 1 Vtop-mount depth: 3-3/16warranty: 1 year60-day returnsMFR # AA2691-AWhats in the box:Polk Audio MM691 owners manualTwo 3-way speakers2 Grilles2 Passive crossovers8 Mounting screws8 Speed clipsOwners ManualProduct Registration information sheet

Pair of Monitor Audio Silver 3007G Tower speakers in Walnut Veneer. Like new condition. Includes original boxes and packing. Please contact me about any questions. I am willing to personally deliver to Twin Cities MN area or my local Fargo/Moorhead area.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

A pair of Polk Audio MM691s. These are generally used for car audio as 6x9 replacement speakers. These have never been used. Purchased for a car long ago and have sat safely in storage for many years. The box is worn, but the components inside are unharmed. Item will be shipped in this box as is. Ill tape it well, though. From the manufacturer:Polk Audio continues its tradition of making brilliant-sounding speakers in stylishly designed packages — their Mobile Monitor (MM) Series speakers look great and sound even better. Each speaker utilizes an extra-strong, extra-small neodymium magnet that saves space and weight, allowing these speakers to fit into more places in more vehicles while still delivering a full sound with lots of kick. Their lightweight carbon composite frames provide strong, flex-free support for the speakers motor assemblies.The Polk MM691 6x9 speakers feature honeycomb-textured woven glass fiber composite woofer cones that respond very quickly for a clean, crisp, and powerful sound. Large voice coils — over an inch in diameter — give the speaker high power handling capability and extended reliability.3/4 and 1 silk dome tweeters add a sweet high end that blends perfectly with the low notes so your music stays in harmonic balance, from the electric bass all the way on up to the cymbals.Important Note: These Polk speakers use a low-impedance design to pull more power safely from your car stereo or amplifier. This design is compatible with virtually all factory and aftermarket stereos.Priced per pairREAD LESSProduct highlights:6x9 3-way speakers (pair)woven honeycomb glass fiber composite woofer cone with butyl rubber surround1 and 3/4 silk composite dome tweeterscertified for marine use2.7-ohm impedance for extra power (compatible with virtually all factory or aftermarket car stereos)power range: 15-125 watts RMS (300 watts peak power)frequency response: 30-25,000 Hzsensitivity: 94 dB @ 1 Vtop-mount depth: 3-3/16warranty: 1 year60-day returnsMFR # AA2691-AWhats in the box:Polk Audio MM691 owners manualTwo 3-way speakers2 Grilles2 Passive crossovers8 Mounting screws8 Speed clipsOwners ManualProduct Registration information sheet

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio RM3000 Monitor Series 2 Speakers, Speckled Stone Color Used. Good condition. One speaker has a tear and there are a few small tears in the speaker covers. Speakers are very heavy. Old school quality.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

Excellent condition, used them carefully for 1 year. Key Features:1 x 1 (25 mm) C-CAM Gold Dome tweeter with Uniform Dispersion (UD) Waveguide II for more lifelike sound1 x 3 (76 mm) C-CAM mid-range driver with Rigid Surface Technology (RST) II for extra clarity2 x 6 (152 mm) C-CAM bass driver with RST II for extra clarity3-way design with dedicated mid-range and bass drivers to deliver the ultimate refinementPerfect for mid to large-sized room set-ups, either stereo or home theater Rear-ported and tuned for ease of positioning without affecting sound performanceSturdy outrigger feet with a choice of spikes for carpets or rubber feet for hard floorsAdd Silver AMS 7G Dolby Atmos® enabled speakers for your home theater system

Crossovers Monitor Audio PL300. Audiophile grade. Slightly used. Perfect condition.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.

MONITOR AUDIO SILVER 300 6G FLOOR STANDING SPEAKERS (PAIR) SATIN WHITE. Tested to be fully functional. Besides some light scuffs / scratches which can barely be seen the pictures, these pair of speakers are in great condition. Speaker and Speaker grill cover only no other accessories. These will be packaged securely and signature required for safe delivery. See detailed pictures. The Monitor Audio Silver 300 floorstander retains the familiar award-winning configuration of its predecessor, with several crucial improvements to drivers. The full three-way design delivers class-leading mid-range, while a pair of long-throw 6-inch bass drivers work together to produce incredible power from the tall, but slim cabinet design, making it the perfect choice for serious audiophile and AV installations.The three-way configuration allows each driver to be optimized to do a better job over a narrower frequency band; the only real way to deliver elevated performance in every respect. Superlatively natural mid-range comes courtesy of a dedicated 4-inch driver, specially designed with ‘under hung’ voice coil and motor system. This technique ensures the voice coil always remains in the magnetic gap under all conditions for demonstrably lower distortion than usually found at this level – an advance which can be immediately heard. TO PREVENT FRAUDSPECIALLY MARKED OR SERIAL # RECORDED PLEASE DONT ASK US TO SHIP TO A DIFFERENT ADDRESS OTHER THAN THE ONE PROVIDED BY EBAY PLEASE UPDATE YOUR SHIPPING ADDRESS BEFORE CHECKOUT THANKS.WARRANTY: WE WILL WARRANTY THE UNIT FREE FROM DEFECTS AS STATED IN THE LISTING DESCRIPTION. ABUSE AND ACCIDENTAL DAMAGE DO NOT QUALIFY FOR WARRANTY COVERAGE. BUYER IS RESPONSIBLE FOR ALL SHIPPING COSTS FOR ANY WARRANTY CLAIMS. WARRANTY START DATE DETERMINED BY DELIVERY DATE AS RECORDED BY YOUR TRACKING NUMBER. CHIPSET, CPU & BOARD SERIAL NUMBERS RECORDED FOR WARRANTY PURPOSES.REFUND POLICY: UNLESS OTHERWISE INDICATED IN THE TERMS OF THE LISTING WE ARE HAPPY TO REFUND YOU UPON RETURN OF THE ORIGINAL ITEM IN ITS ORIGINAL CONDITION AS SENT TO YOU WITHIN 30 DAYS ONLY IF ITEM IS NOT AS DESCRIBED. THIS DETERMINED BY THE DAY YOU RECEIVED THE ITEM BASED ON THE INFORMATION PROVIDED BY THE TRACKING NUMBER. NO REFUNDS AFTER 30 DAYS.IF THE ITEM COMES BACK TO US IN THE DESCRIBED CONDITION AND FUNCTIONAL THEN THERE WILL BE 20% RESTOCKING FEE.

Pair of Polk Audio RM3000 Monitor Series-2 Satellite Speakers Gray Black. Condition is Used. Shipped with USPS Priority Mail.