Lyngdorf SDA 2175 High-Performance Power Amplifier.Working, excellent sound.Has some scratches.Comes with power cord.MADE IN DENMARK.SpecificationsPower output: 200 watts per channel into 8? (stereo)Frequency response: 0.3Hz to 33kHzTotal harmonic distortion: 0.01%Signal to noise ratio: 117dBSpeaker load impedance: 4? to 8?Dimensions: 450 x 361 x 100.6mmWeight: 13kgDescriptionThe SDA 2175 is a high-performance power amplifier designed without compromise. It can act as a controllable amplifier in Lyngdorf systems or as a power amplifier for conventional pre-amplifiers.The SDA 2175 is not your regular class D power amplifier. The output stage uses Pulse Width Modulation with a patented switch speed optimization technology. This ensures a low and linear natural distortion, and an unmatchable performance is achieved by using less feedback compared to typical Class D amplifiers.And the fully balanced signal path all the way through the amplifier to the PWM conversion stage guarantees a remarkable performance with a signal-to-noise ratio superior to any other Class D amplifier in the market!Careful and sensitive design touches can be seen throughout the amplifier: it starts at the mains input with a low-noise Holmgren toroidal transformer with power supply feed-forward compensation, suppressing the variations in the output rather than relying on feedback-based error correction normally used. This feed-forward technique originates from the design of the Millennium – the Lyngdorf state-of-the-art true digital amplifier.In the critical output stage only the highest quality components have been used, e.g. polypropylene capacitors and linear ferrite material in the output filter. Combined with other techniques this results in low and frequency-independent distortion. Consequently wideband musical instruments can be re-played without any added harmonics – any source will be recreated to sound the way it was recorded.Semi Digital Amplifier“Semi Digital” is in Lyngdorf terms a “digital” switching amplifier driven by an analog input. In principle, the output stage of most switching amplifiers has the same working principle. PWM = Pulse Width Modulation is simply a matter of variable open/close time of the transistors.Fully balanced signal pathThe amplifier is fully balanced from input to output if driven with a balanced source, and if not driven with a balanced source, the signal is immediately transformed to a balanced signal.The fully balanced design gives clear advantages regarding hum and noise suppression – also from other sources. And the balanced design is not only used in the signal path – even the feedback loop internally in the output stage is designed to be fully balanced.The signal path is furthermore DC coupled to the widest extent – except from DC blocking capacitors in the input the construction is DC coupled through the rest of the construction leaving no discussion about capacitor quality.In the analog signal chain only the highest quality components are used as Ultra low distortion Burr-Brown op-amps in the input stage and Polypropylene capacitors in the output reconstruction filter.Finish: black.

Lyngdorf SDA 2175 High-Performance Power Amplifier.Working, excellent sound.Has some scratches.Comes with power cord.MADE IN DENMARK.SpecificationsPower output: 200 watts per channel into 8? (stereo)Frequency response: 0.3Hz to 33kHzTotal harmonic distortion: 0.01%Signal to noise ratio: 117dBSpeaker load impedance: 4? to 8?Dimensions: 450 x 361 x 100.6mmWeight: 13kgDescriptionThe SDA 2175 is a high-performance power amplifier designed without compromise. It can act as a controllable amplifier in Lyngdorf systems or as a power amplifier for conventional pre-amplifiers.The SDA 2175 is not your regular class D power amplifier. The output stage uses Pulse Width Modulation with a patented switch speed optimization technology. This ensures a low and linear natural distortion, and an unmatchable performance is achieved by using less feedback compared to typical Class D amplifiers.And the fully balanced signal path all the way through the amplifier to the PWM conversion stage guarantees a remarkable performance with a signal-to-noise ratio superior to any other Class D amplifier in the market!Careful and sensitive design touches can be seen throughout the amplifier: it starts at the mains input with a low-noise Holmgren toroidal transformer with power supply feed-forward compensation, suppressing the variations in the output rather than relying on feedback-based error correction normally used. This feed-forward technique originates from the design of the Millennium – the Lyngdorf state-of-the-art true digital amplifier.In the critical output stage only the highest quality components have been used, e.g. polypropylene capacitors and linear ferrite material in the output filter. Combined with other techniques this results in low and frequency-independent distortion. Consequently wideband musical instruments can be re-played without any added harmonics – any source will be recreated to sound the way it was recorded.Semi Digital Amplifier“Semi Digital” is in Lyngdorf terms a “digital” switching amplifier driven by an analog input. In principle, the output stage of most switching amplifiers has the same working principle. PWM = Pulse Width Modulation is simply a matter of variable open/close time of the transistors.Fully balanced signal pathThe amplifier is fully balanced from input to output if driven with a balanced source, and if not driven with a balanced source, the signal is immediately transformed to a balanced signal.The fully balanced design gives clear advantages regarding hum and noise suppression – also from other sources. And the balanced design is not only used in the signal path – even the feedback loop internally in the output stage is designed to be fully balanced.The signal path is furthermore DC coupled to the widest extent – except from DC blocking capacitors in the input the construction is DC coupled through the rest of the construction leaving no discussion about capacitor quality.In the analog signal chain only the highest quality components are used as Ultra low distortion Burr-Brown op-amps in the input stage and Polypropylene capacitors in the output reconstruction filter.Finish: black.

Lyngdorf SDA 2175 High-Performance Power Amplifier.Working, excellent sound.Has some scratches.Comes with power cord.MADE IN DENMARK.SpecificationsPower output: 200 watts per channel into 8? (stereo)Frequency response: 0.3Hz to 33kHzTotal harmonic distortion: 0.01%Signal to noise ratio: 117dBSpeaker load impedance: 4? to 8?Dimensions: 450 x 361 x 100.6mmWeight: 13kgDescriptionThe SDA 2175 is a high-performance power amplifier designed without compromise. It can act as a controllable amplifier in Lyngdorf systems or as a power amplifier for conventional pre-amplifiers.The SDA 2175 is not your regular class D power amplifier. The output stage uses Pulse Width Modulation with a patented switch speed optimization technology. This ensures a low and linear natural distortion, and an unmatchable performance is achieved by using less feedback compared to typical Class D amplifiers.And the fully balanced signal path all the way through the amplifier to the PWM conversion stage guarantees a remarkable performance with a signal-to-noise ratio superior to any other Class D amplifier in the market!Careful and sensitive design touches can be seen throughout the amplifier: it starts at the mains input with a low-noise Holmgren toroidal transformer with power supply feed-forward compensation, suppressing the variations in the output rather than relying on feedback-based error correction normally used. This feed-forward technique originates from the design of the Millennium – the Lyngdorf state-of-the-art true digital amplifier.In the critical output stage only the highest quality components have been used, e.g. polypropylene capacitors and linear ferrite material in the output filter. Combined with other techniques this results in low and frequency-independent distortion. Consequently wideband musical instruments can be re-played without any added harmonics – any source will be recreated to sound the way it was recorded.Semi Digital Amplifier“Semi Digital” is in Lyngdorf terms a “digital” switching amplifier driven by an analog input. In principle, the output stage of most switching amplifiers has the same working principle. PWM = Pulse Width Modulation is simply a matter of variable open/close time of the transistors.Fully balanced signal pathThe amplifier is fully balanced from input to output if driven with a balanced source, and if not driven with a balanced source, the signal is immediately transformed to a balanced signal.The fully balanced design gives clear advantages regarding hum and noise suppression – also from other sources. And the balanced design is not only used in the signal path – even the feedback loop internally in the output stage is designed to be fully balanced.The signal path is furthermore DC coupled to the widest extent – except from DC blocking capacitors in the input the construction is DC coupled through the rest of the construction leaving no discussion about capacitor quality.In the analog signal chain only the highest quality components are used as Ultra low distortion Burr-Brown op-amps in the input stage and Polypropylene capacitors in the output reconstruction filter.Finish: black.

Lyngdorf SDA 2175 High-Performance Power Amplifier.Working, excellent sound.Has some scratches.Comes with power cord.MADE IN DENMARK.SpecificationsPower output: 200 watts per channel into 8? (stereo)Frequency response: 0.3Hz to 33kHzTotal harmonic distortion: 0.01%Signal to noise ratio: 117dBSpeaker load impedance: 4? to 8?Dimensions: 450 x 361 x 100.6mmWeight: 13kgDescriptionThe SDA 2175 is a high-performance power amplifier designed without compromise. It can act as a controllable amplifier in Lyngdorf systems or as a power amplifier for conventional pre-amplifiers.The SDA 2175 is not your regular class D power amplifier. The output stage uses Pulse Width Modulation with a patented switch speed optimization technology. This ensures a low and linear natural distortion, and an unmatchable performance is achieved by using less feedback compared to typical Class D amplifiers.And the fully balanced signal path all the way through the amplifier to the PWM conversion stage guarantees a remarkable performance with a signal-to-noise ratio superior to any other Class D amplifier in the market!Careful and sensitive design touches can be seen throughout the amplifier: it starts at the mains input with a low-noise Holmgren toroidal transformer with power supply feed-forward compensation, suppressing the variations in the output rather than relying on feedback-based error correction normally used. This feed-forward technique originates from the design of the Millennium – the Lyngdorf state-of-the-art true digital amplifier.In the critical output stage only the highest quality components have been used, e.g. polypropylene capacitors and linear ferrite material in the output filter. Combined with other techniques this results in low and frequency-independent distortion. Consequently wideband musical instruments can be re-played without any added harmonics – any source will be recreated to sound the way it was recorded.Semi Digital Amplifier“Semi Digital” is in Lyngdorf terms a “digital” switching amplifier driven by an analog input. In principle, the output stage of most switching amplifiers has the same working principle. PWM = Pulse Width Modulation is simply a matter of variable open/close time of the transistors.Fully balanced signal pathThe amplifier is fully balanced from input to output if driven with a balanced source, and if not driven with a balanced source, the signal is immediately transformed to a balanced signal.The fully balanced design gives clear advantages regarding hum and noise suppression – also from other sources. And the balanced design is not only used in the signal path – even the feedback loop internally in the output stage is designed to be fully balanced.The signal path is furthermore DC coupled to the widest extent – except from DC blocking capacitors in the input the construction is DC coupled through the rest of the construction leaving no discussion about capacitor quality.In the analog signal chain only the highest quality components are used as Ultra low distortion Burr-Brown op-amps in the input stage and Polypropylene capacitors in the output reconstruction filter.Finish: black.

Lyngdorf SDA 2175 High-Performance Power Amplifier.Working, excellent sound.Has some scratches.Comes with power cord.MADE IN DENMARK.SpecificationsPower output: 200 watts per channel into 8? (stereo)Frequency response: 0.3Hz to 33kHzTotal harmonic distortion: 0.01%Signal to noise ratio: 117dBSpeaker load impedance: 4? to 8?Dimensions: 450 x 361 x 100.6mmWeight: 13kgDescriptionThe SDA 2175 is a high-performance power amplifier designed without compromise. It can act as a controllable amplifier in Lyngdorf systems or as a power amplifier for conventional pre-amplifiers.The SDA 2175 is not your regular class D power amplifier. The output stage uses Pulse Width Modulation with a patented switch speed optimization technology. This ensures a low and linear natural distortion, and an unmatchable performance is achieved by using less feedback compared to typical Class D amplifiers.And the fully balanced signal path all the way through the amplifier to the PWM conversion stage guarantees a remarkable performance with a signal-to-noise ratio superior to any other Class D amplifier in the market!Careful and sensitive design touches can be seen throughout the amplifier: it starts at the mains input with a low-noise Holmgren toroidal transformer with power supply feed-forward compensation, suppressing the variations in the output rather than relying on feedback-based error correction normally used. This feed-forward technique originates from the design of the Millennium – the Lyngdorf state-of-the-art true digital amplifier.In the critical output stage only the highest quality components have been used, e.g. polypropylene capacitors and linear ferrite material in the output filter. Combined with other techniques this results in low and frequency-independent distortion. Consequently wideband musical instruments can be re-played without any added harmonics – any source will be recreated to sound the way it was recorded.Semi Digital Amplifier“Semi Digital” is in Lyngdorf terms a “digital” switching amplifier driven by an analog input. In principle, the output stage of most switching amplifiers has the same working principle. PWM = Pulse Width Modulation is simply a matter of variable open/close time of the transistors.Fully balanced signal pathThe amplifier is fully balanced from input to output if driven with a balanced source, and if not driven with a balanced source, the signal is immediately transformed to a balanced signal.The fully balanced design gives clear advantages regarding hum and noise suppression – also from other sources. And the balanced design is not only used in the signal path – even the feedback loop internally in the output stage is designed to be fully balanced.The signal path is furthermore DC coupled to the widest extent – except from DC blocking capacitors in the input the construction is DC coupled through the rest of the construction leaving no discussion about capacitor quality.In the analog signal chain only the highest quality components are used as Ultra low distortion Burr-Brown op-amps in the input stage and Polypropylene capacitors in the output reconstruction filter.Finish: black.

I am the original owner of this outstanding, powerful and versatile Lyngdorf SDA-2400 amplifier. It has very light use and is super clean. It looks and works great. Moving into a new home and no longer have a use for it. Local Pickup welcome. Mainland USA shipping only. Look at my long history of 100% positive feedback on ebay and bid with confidence. Manufacturers website: https://lyngdorf.steinwaylyngdorf.com/lyngdorf-sda-2400/

Angeboten wird eine Frontplatte und eine Deckplatte fr Lyngdorf / TACT SDA 2175 Semi Digital Amplifier. Beide Teile haben Gebrauchsspuren, wie den Bildern zu entnehmen ist. Verkauf als Ersatzteil / defekt. Lieferumfang: Frontplatte fr Lyngdorf / TACT SDA 2175 Deckplatte fr Lyngdorf / TACT SDA 2175 – – Verkauf von Privat unter Ausschluß von Gewährleistung. Dem Käufer steht es frei, den zu erwerbenen Artikel vor Kauf in Augenschein zu nehmen und ggf. auf einwandfreie Funktion zu überprüfen. Alle Angaben zum Zustand des angebotenen Artikels sind mit bestem Wissen und Gewissen gemacht. Ich übernehme keine Gewähr für versteckte Mängel. Beim Versenden geht das Risiko für die Beschaffenheit des Artikels mit der Übergabe an den Versanddienstleister auf den Käufer über. Bieten oder kaufen Sie nicht, wenn Sie mit diesen Bedingungen nicht einverstanden sind. Private sale to the exclusion of warranty. The buyer is free to inspect the item to be purchased before purchase and, if necessary, to check that it is in perfect working order. All information on the condition of the offered item are made with the best of knowledge and belief. I assume no liability for hidden defects. When shipping, the risk for the constitution of the item passes to the buyer with the transfer to the shipping service provider. Do not bid or buy if you disagree with these terms. _gsrx_vers_1634 (GS 9.6 (1634))

Lyngdorf SDA-2400 Class D Endstufe in Topzustand. Alles Zubehör dabei in OVP, funktioniert tadellos. Neukauf in 3/2022 im Fachhandel, Rechnung anbei. Audiophile Digitalendstufe, betrieben an TAD Lautsprecher im BiAmping mit einer zweiten SDA-2400...Jetzt Umstieg auf Lyngdorf MXA-8400. Derzeitiger NP. ist 2600 - 3000€. Versand mit Höherversicherung.

Ich verkaufe hier meine High-End Endstufe Lyngdorf SDA-2400 . Sie ist in einem sehr guten Zustand, technisch absolut einwandfrei. Keine Macken. Ich verkaufe nur, weil ich eine Mehrkanal-Endstufe umsteigen möchte. Herausragende Klangqualität bei einer Leistung von 2 x 200/400 Watt an 8/4 Ohm, treibt praktisch jeden Lautsprecher mühelos an. Die SDA-2400 bietet neben XLR und RCA noch digitale Eingänge: 1x Coax und 1x Spdif (per Wahlschalter hinten wählbar). Lieferumfang: - natürlich die Endstufe SDA-2400 - Netzkabel - Trigger Kabel - Originalverpackung Versand versichert bis 2500 Euro per DHL. Keine Rücknahme. Keine Garantie.