Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

Heres a pair of the legendary Rogers LS5 loudspeakers. 8 ohms, 100W, +/-2.5db 65-18Khz. Walnut (I think) cabinets. Age unknown; the date code is written 13R4 on the small mfg QA label in the lower corner of the rear. Mfg is Swisstone Electronics, a business acquisition to continue the manufacture of the speaker line (history and nature of it is on the web) without altering design and quality. Cabinet dimensions: 18 x 8-3/16 x 8-13/16. Driver dimensions: 7-3/16 woofer; 4 tweeter and 1-3/4 port. One unit has a woofer defect. As seen in the photos the dust cap over the voice coil is missing. Also the cone (white-opaque portion) and the surround are no longer bonded by the adhesive. The other unit is good. I bought these 2nd hand years ago and tested the speakers prior to removing the grill and finding the adhesive problem. I used a decent quality power (Carvin) and pre amplifier (Phillips). Source was a CD. I listened at mid and high volume. I did not hear any cone rattling or distortion. Since the surround has not deteriorated and the cone is good you may be able to repair it. The cabinet finish is good overall. There are small scratches and discolorations as seen in the photos. Slight damage on one corner (photo). Another corner has a small bit of damage near it. As seen, unfortunately the former owner installed rubber bumpers on one side of each unit. One has 4 intact, the other has two. Some bumpers slipped aside what I assume is an adhesive pad. Theres no grill defects. This is a heavy shipment but will be well packed for a safe trip.

classic rogers ls5 speakers/monitors, sound great.

Der angezeigte Versand gilt für Länder innerhalb der EU.Wenn Sie außerhalb der Europäischen Union ansässig sind, beachten Sie bitte, dass die aktuellen Versandkosten aus Portugal hoch sind.Wenn Sie auf diesen Artikel bieten möchten, kontaktieren Sie mich bitte vorher, um die korrekten Versandkosten zu erfahren.Zum Verkauf steht ein Paar Vintage-Hi-End-Lautsprecher von Rogers aus den 1990er Jahren. Sie befinden sich in einem sehr guten ästhetischen und betriebstechnischen Zustand und wurden so konzipiert, dass sie der Musik feinste Details und Tiefe wiedergeben und dabei die Bi-Amping-Verbindung nutzen, die an jedem Lautsprecher verfügbar ist (unabhängige Verstärkung für hohe und niedrige Frequenzen).Beide Lautsprecher werden im selben Paket (26 kg) verschickt, sehr sorgfältig verpackt, um den modernen Kurierdiensten standzuhalten ... The displayed shipping applies to countries within-EU. If you are located outside the European Union, please be advised that current shipping prices from Portugal are expensive; if you wish to bid on this item, please contact me beforehand in order to obtain a correct shipping cost. For sale, a vintage Hi-End pair of Rogers speakers from the 1990s. In very good aesthetic and operation condition, they were conceived to render the finest detail and depth to music, taking advantage of the bi-amping connection available at each speaker (independent amplification for high and low frequencies).Both speakers will be shipped in the same package (26Kg), very thouroughly packed to endure modern day courier services...

Very nice vintage Rogers BBC LS5/9 Stereo Speakers with original matching wood stands.These are the bigger, better brothers to the LS3/5a Original 1990s version; not the current reissue.Matching A/B Serial Numbers Original owner. Lightly used. Very Good original condition.Some fading to real wood veneers from exposure to sunlight.100% original. The grills have only been taken off the one time to photograph drivers Id like to sell these locally (San Francisco CA 94109) due to the stands and lack of boxes.Potential buyers can audition the speaker before finalizing purchase.

ROGERS LS55 Crossover TWO in this SALE ( BI-WIRE CONNECTION ) SEE ALL PHOTOS buy the two seen in photo two for only £15 SUPERB FULL TESTED COMES WITH FOUR SCREWS

ROGERS LS5/9 VINTAGE SPEAKERS MATCHED Originally black ash but quite badly scratched, I have re-veneered these in book-matched oak. The top and right front edges of one speaker’s veneer is slightly less flush compared to the rest but this is only noticeable when looking directly down or side on, and does not detract from the overall appearance, which is very good. The drivers are all in excellent condition, as are the grills. PLEASE NOTE Pictured stands are NOT included in this auction Although I do not have the original packaging, these will be shipped in a custom made box with strong (3 cm wide) foam inserts to protect the corners and sides. Postage will be next day delivery with insurance, hence the high price. UK buyers only, please

MY0021.FROM A SMOKE FREE HOME ..............HI-FI NEWS VINTAGE AUREX SB-A10 ROGERS LS5/9A CLASSIC SE AUDIO RESEARCH REF80S HI-FI NEWS SEE ALL REVEWS ROGERS LS5/9A CLASSIC SE - YAMAHA A S3200 - AUDIO RESEARCH REF80S HI-FI NEWS - ROGERS - YAMAHA - AUDIO RESEARCH - SYSTEM AUDIO - MERASON - AUREX HI-FI NEWS - AUREX SB-A10 AMPLIFIER - WILSON AUDIO SYSTEM V - ROGERS LS5/9 CLASSIC SE

Pair of Rogers LS 5/8 active monitor loudspeakers complete with stands, correct Quad 405 amplifiers and cables. In excellent condition, these are rare and highly sought after. Collection in person from HP27 9LG UK.