KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.

Klipsch RW 10 Powered 10 Subwoofer (Black) Great Buy Shipping International! Actual photos, looks great. Sounds great. PAYMENT INFO: Payment is due immediately after the auction end. If you cannot pay immediately after the auction but want to bid please contact me and let me know when you will be able to send payment and I will let you know if you can bid. If your feedback is less than 10, please contact me before bidding just to let me know that you are a real person and not someone that is going to bid and not pay. If you do not contact me before bidding, I will try to contact you and if you do not respond then I will cancel your bids and block your user id. SHIPPING INFO I will ship this out by the next day via FedEx after the payment is received. Your tracking number will be automatically sent to you when it goes out. I always pack well and insurance is always included! INTERNATIONAL BUYERS This will be fully insured. I do have express shipping available so feel free to ask for a quote. I dont lie on customs forms so please dont ask me to mark down invoices. Customs, taxes and or duties may apply. Thanks For Looking!

Klipsch RF-25 Speakers amd RW-12 Subwoofer. The speakers sound amazing and are in perfect working condition. The cloth on the speaker grilles needs to be replaced.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.