UPS shipping estimate is between $50 - $90, depending on location. Price reduced to $3100.00; buyer pays shipping costs. Features:Three balanced XLR inputs per channel plus three unbalanced (RCA) inputs per channel.Preamp Out in both balanced XLR output and unbalanced (RCA) outputs per channel.Tape input and output jacks allow tape recording from any source and monitoring of tape recorder output.Rear panel handles assist moving and transport of unit.Chassis and all chassis components, precision machined from 6061 aluminum plate, reduce distortion resulting from mechanical resonance and thermal instabilities.All operational functions under microprocessor control. Within five seconds of any function selected, the microprocessor reverts to a nonclocking “sleep” mode which eliminates any possibility of digital noise contamination.Non-multiplexed, zero electrical noise generating numerical display indicates volume level over entire range of 99.5 decibels.‘Display off after five seconds’ option available for non-intrusive, low light listening environments.Dual range volume control allows large volume level changes when knob is rotated abruptly, yet permits precise small volume level changes when knob is rotated slowly.Optional plug-in phono cards (installed internally) convert Line Input 1 to high performance phono inputs. Four gain and input loading options standard for moving magnet and moving coil cartridge types.Full electronic and thermal protection modes guard against output overloads and short circuits.High current preamp outputs (balanced XLR and unbalanced RCA) allow simultaneous driving of external power amplifiers for subwoofers, vertical bi-amping, etc.All inputs are transformer-coupled to provide maximum immunity from RF contamination and system ground loops and enhance compatibility with a wide variety of interconnected components.Speaker outputs are fully balanced to provide maximum sonic performance and immunity from RF contamination due to high output common mode noise rejection.Optical encoder type volume control maintains quiet, trouble-free performance and accuracy over entire lifetime of product. þ Six-function hand-held IR remote control. There is no official info on the matter of output stage but it seems that the LM3886 integrated amplification circuits have been used instead of bipolar transistors. This integrated amplifier has created quite a stir in high-end circles. It has a modest 100 watts of power but just like all Rowland amps, it was much more powerful than these figures would lead you to believe.All Concentras have a balance control which makes sense because they contain a version of the Synergy preamp inside. Using the remote control, the balance will work but this just is not indicated on the front panel. To reset the balance, press “Mute” for a couple of seconds.Note: I have removed the 9-volt battery from the remote.Specifications:Output Power Continuous RMS Watts@ 8 ohms 100 watts@ 4 ohms150 wattsBandwidth0.5 Hz to 160 kHz, -3 dBSlew Rate30 volts per microsecondTHD and NoiseLess than 0.06% at rated powerDamping Factor60, 20 Hz to 20 kHz, 8 ohmsOutput Current16 amps continuous, 28 amps peakGain StructurePreamplifier Section 14 dBAmplifier Section26 dBVolume Control Range99.5 dBVolume Control Resolution0.5 dB ±0.05 dB over entire rangeInput Impedance36k ohmCommon Mode Rejection Ratio Greater than 60 dB, 20 Hz to 20 kHzPower Consumption100 watts idle; 550 watts maximumInputsBalanced Line3 per channel (XLR)Unbalanced Line3 per channel (RCA)Record1 per channel (RCA)Unbalanced Phono (optional)1 per channel (RCA)OutputsBalanced Pre Out1 per channel (XLR)Unbalanced Pre Out1 per channel (RCA)Record1 per channel (RCA)Speaker1 pair binding posts per channelDimensions17.5 in (W) x 14.35 in (D) x 5.75 in (H) 44.5 cm (W) x 36.2 cm (D) x 14.6 cm (H)Weight50 lbs (23 kg)

UNTESTED it powers up (no generic power cord Included). Lost screws for top cover. Shows in really nice shape. Has receiver and remote and manual. I’m not an audio expert so I wouldn’t know how to test is. Lights in side light up as well. This Jeff Rowland Design Group Consonance Preamplifier is a high-quality unit that is perfect for audiophiles. It features two channels and comes in a sleek black color. The preamp is designed to work with a variety of units and is compatible with most types of audio equipment. It also comes with a remote control, making it easy to adjust the settings from anywhere in the room.

Jeff Rowland Capri S Preamplifier. Very nice cosmetic condition and works as it should, no issues.Phono card installed. Ships in original box with remote. Remote has a crack on back near the screw but works as it should

Our products are 100% authentic! DescriptionCondition: Good ConditionNormal operation has been confirmed. The exterior is relatively clean with few scratches.However, the paint on the front MUTE mark is partially chipped (see Photo 5).Also, there are cracks and chips on the bottom of the remote control, which have been repaired with adhesive (see Photo 6) The No. 1 input terminal is a phono terminal.It is currently set to 60 dB gain and 100 ? input impedance to match MC type, but the settings can be changed with an internal jumper. Please confirm the state with a photograph. PaymentWe will ship the item 3~10 business days after your payment clears.ShippingWe ship via Fedex or DHL or Japan Post. All orders will be shipped with tracking number. Please bid with confidence.I will only ship to addresses that are registered with ebay. Please note that we cannot ship to non-registered addresses.Terms of SaleReturnsReturns are accepted ONLY if the item was not the item described.International Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.

Jeff Rowland Cadence phono stage PLEASE NOTE THE Synergy IIi IS NOT PART OF THIS LISTING!!! - it is on a sperate listing.YED TO SOURCE THE POWER STORAGE/SUPPLY UNIT SEPERATELY, does not work without it, as I cannot find it in the storage.Would run from the synergy dc power supply/storage.