fidelity-research FR FR-7f Shell Integrated Stereo Moving Coil MC Cartridge #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. The cantilever is not broken or bent. Stylus tip and damper are in good condition. Original case included. Overview Shell-integrated MC cartridge, an improved version of the FR-7. It uses a unique push-pull power generation system with a 2-magnet, 4-pole magnetic circuit.This system generates power at four points, so that a large output voltage can be obtained even with a low-impedance coil. In addition, although the general system generates canceled current in the generator circuit, the FR-7fs magnetic circuit can generate positive output in the opposite direction even in the region where canceled current occurs. This improves the phase and crosstalk characteristics as well as the electrical conversion efficiency, resulting in higher output power. A samarium-cobalt magnet is used as the magnetic circuit material. These magnets have a higher coercive force and are less likely to self-demagnetize than ordinary alnico magnets, thus maintaining the initial characteristics of the magnetic circuit for a long period of time. The generator coil uses a completely air-core coil without a winding frame, which prevents unwanted magnetic materials from moving within the generator field and fundamentally eliminates distortion of the reproduced signal. The effective mass of the resonator is also reduced to about 2/3, resulting in a smaller mechanical impedance in the high frequency range. For the needle tip, a unique refined-contact needle made of solid 0.15 mm square diamond is used.The new method of using a refined contact needle combines the advantages of a line-contact needle with those of an oval needle, making it less susceptible to adverse effects (noise, etc.) caused by the warping of the disc and dust in the sound groove. The new needle is less susceptible to the adverse effects (e.g., noise) of warpage and dust in the sound grooves of a disc, and generates very little scratch and surface noise, resulting in a clear and uninterrupted playback sound. A special aluminum alloy cantilever is used for the cantilever.This is a straight cantilever made of a highly corrosion-resistant special aluminum alloy with optimum heat-hardening treatment (ceramic treatment) to minimize the moment of inertia and deflection during high-speed movement. The leading part of the string holder extends to the front of damper B, which makes the fulcrum position clearer. This clarifies the cantilever vibration fulcrum position and minimizes the cantilever vibration distance variation at each frequency.In addition, the string wire used to tension the cantilever is made of a material with a very high spring coefficient and little change over time, which contributes to the improvement of the square wave characteristics. A dual damper system is employed, with two layers of dampers with different rubber coefficients to effectively dump the mid-high and mid-low frequencies of the vibration frequency respectively, enabling ideal tracing over the entire reproduction frequency range.In addition, the rubber coefficients of damper A and B are different to reduce the total effect of temperature on tracing performance, mechanical impedance characteristics, and reproduced sound. To solve the problem of coil lead wires vibrating with the cantilever, coil lead wires are inserted and crimped between dampers A and B to eliminate unwanted power generation by the lead wires. The head shell is shaped to completely remove dead space that could cause parasitic vibration, which is detrimental to sound quality. The shell is made of a special aluminum alloy, which is impact-machined (cold-forged) to further increase rigidity and prevent split resonance. The cartridge body is made of epoxy resin, which was selected through careful audibility tests. To improve the lack of strength caused by rattling between the arm and connector section, a special stainless steel locking plate is used in place of the conventional guide pin. This allows for a more integrated connection with the arm, and the level can be maintained correctly. Specifications Type: MC CartridgeOutput voltage 0.15mV(3.54cm/sec., 45?)0.2mV(5cm/sec., 45?)Output power 2x10-8W(5cm/sec.45?)Needle pressure 2g to 3gCoil impedance 2?Load impedance 3?Playback frequency range 10Hz to 45kHzChannel balance 1dB(1kHz)Channel separation -28dB(1kHz)Compliance 7x10-6cm/dyne(100Hz, 20°C)Needle tip 0.15mm square refined-contact solid diamond needleWeight 30g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

fidelity-research FR FR-7f Shell Integrated Stereo Moving Coil MC Cartridge #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. The cantilever is not broken or bent. Stylus tip and damper are in good condition. Original case included. Overview Shell-integrated MC cartridge, an improved version of the FR-7. It uses a unique push-pull power generation system with a 2-magnet, 4-pole magnetic circuit.This system generates power at four points, so that a large output voltage can be obtained even with a low-impedance coil. In addition, although the general system generates canceled current in the generator circuit, the FR-7fs magnetic circuit can generate positive output in the opposite direction even in the region where canceled current occurs. This improves the phase and crosstalk characteristics as well as the electrical conversion efficiency, resulting in higher output power. A samarium-cobalt magnet is used as the magnetic circuit material. These magnets have a higher coercive force and are less likely to self-demagnetize than ordinary alnico magnets, thus maintaining the initial characteristics of the magnetic circuit for a long period of time. The generator coil uses a completely air-core coil without a winding frame, which prevents unwanted magnetic materials from moving within the generator field and fundamentally eliminates distortion of the reproduced signal. The effective mass of the resonator is also reduced to about 2/3, resulting in a smaller mechanical impedance in the high frequency range. For the needle tip, a unique refined-contact needle made of solid 0.15 mm square diamond is used.The new method of using a refined contact needle combines the advantages of a line-contact needle with those of an oval needle, making it less susceptible to adverse effects (noise, etc.) caused by the warping of the disc and dust in the sound groove. The new needle is less susceptible to the adverse effects (e.g., noise) of warpage and dust in the sound grooves of a disc, and generates very little scratch and surface noise, resulting in a clear and uninterrupted playback sound. A special aluminum alloy cantilever is used for the cantilever.This is a straight cantilever made of a highly corrosion-resistant special aluminum alloy with optimum heat-hardening treatment (ceramic treatment) to minimize the moment of inertia and deflection during high-speed movement. The leading part of the string holder extends to the front of damper B, which makes the fulcrum position clearer. This clarifies the cantilever vibration fulcrum position and minimizes the cantilever vibration distance variation at each frequency.In addition, the string wire used to tension the cantilever is made of a material with a very high spring coefficient and little change over time, which contributes to the improvement of the square wave characteristics. A dual damper system is employed, with two layers of dampers with different rubber coefficients to effectively dump the mid-high and mid-low frequencies of the vibration frequency respectively, enabling ideal tracing over the entire reproduction frequency range.In addition, the rubber coefficients of damper A and B are different to reduce the total effect of temperature on tracing performance, mechanical impedance characteristics, and reproduced sound. To solve the problem of coil lead wires vibrating with the cantilever, coil lead wires are inserted and crimped between dampers A and B to eliminate unwanted power generation by the lead wires. The head shell is shaped to completely remove dead space that could cause parasitic vibration, which is detrimental to sound quality. The shell is made of a special aluminum alloy, which is impact-machined (cold-forged) to further increase rigidity and prevent split resonance. The cartridge body is made of epoxy resin, which was selected through careful audibility tests. To improve the lack of strength caused by rattling between the arm and connector section, a special stainless steel locking plate is used in place of the conventional guide pin. This allows for a more integrated connection with the arm, and the level can be maintained correctly. Specifications Type: MC CartridgeOutput voltage 0.15mV(3.54cm/sec., 45?)0.2mV(5cm/sec., 45?)Output power 2x10-8W(5cm/sec.45?)Needle pressure 2g to 3gCoil impedance 2?Load impedance 3?Playback frequency range 10Hz to 45kHzChannel balance 1dB(1kHz)Channel separation -28dB(1kHz)Compliance 7x10-6cm/dyne(100Hz, 20°C)Needle tip 0.15mm square refined-contact solid diamond needleWeight 30g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

fidelity-research FR FR-7f Shell Integrated Stereo Moving Coil MC Cartridge #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. The cantilever is not broken or bent. Stylus tip and damper are in good condition. Original case included. Overview Shell-integrated MC cartridge, an improved version of the FR-7. It uses a unique push-pull power generation system with a 2-magnet, 4-pole magnetic circuit.This system generates power at four points, so that a large output voltage can be obtained even with a low-impedance coil. In addition, although the general system generates canceled current in the generator circuit, the FR-7fs magnetic circuit can generate positive output in the opposite direction even in the region where canceled current occurs. This improves the phase and crosstalk characteristics as well as the electrical conversion efficiency, resulting in higher output power. A samarium-cobalt magnet is used as the magnetic circuit material. These magnets have a higher coercive force and are less likely to self-demagnetize than ordinary alnico magnets, thus maintaining the initial characteristics of the magnetic circuit for a long period of time. The generator coil uses a completely air-core coil without a winding frame, which prevents unwanted magnetic materials from moving within the generator field and fundamentally eliminates distortion of the reproduced signal. The effective mass of the resonator is also reduced to about 2/3, resulting in a smaller mechanical impedance in the high frequency range. For the needle tip, a unique refined-contact needle made of solid 0.15 mm square diamond is used.The new method of using a refined contact needle combines the advantages of a line-contact needle with those of an oval needle, making it less susceptible to adverse effects (noise, etc.) caused by the warping of the disc and dust in the sound groove. The new needle is less susceptible to the adverse effects (e.g., noise) of warpage and dust in the sound grooves of a disc, and generates very little scratch and surface noise, resulting in a clear and uninterrupted playback sound. A special aluminum alloy cantilever is used for the cantilever.This is a straight cantilever made of a highly corrosion-resistant special aluminum alloy with optimum heat-hardening treatment (ceramic treatment) to minimize the moment of inertia and deflection during high-speed movement. The leading part of the string holder extends to the front of damper B, which makes the fulcrum position clearer. This clarifies the cantilever vibration fulcrum position and minimizes the cantilever vibration distance variation at each frequency.In addition, the string wire used to tension the cantilever is made of a material with a very high spring coefficient and little change over time, which contributes to the improvement of the square wave characteristics. A dual damper system is employed, with two layers of dampers with different rubber coefficients to effectively dump the mid-high and mid-low frequencies of the vibration frequency respectively, enabling ideal tracing over the entire reproduction frequency range.In addition, the rubber coefficients of damper A and B are different to reduce the total effect of temperature on tracing performance, mechanical impedance characteristics, and reproduced sound. To solve the problem of coil lead wires vibrating with the cantilever, coil lead wires are inserted and crimped between dampers A and B to eliminate unwanted power generation by the lead wires. The head shell is shaped to completely remove dead space that could cause parasitic vibration, which is detrimental to sound quality. The shell is made of a special aluminum alloy, which is impact-machined (cold-forged) to further increase rigidity and prevent split resonance. The cartridge body is made of epoxy resin, which was selected through careful audibility tests. To improve the lack of strength caused by rattling between the arm and connector section, a special stainless steel locking plate is used in place of the conventional guide pin. This allows for a more integrated connection with the arm, and the level can be maintained correctly. Specifications Type: MC CartridgeOutput voltage 0.15mV(3.54cm/sec., 45?)0.2mV(5cm/sec., 45?)Output power 2x10-8W(5cm/sec.45?)Needle pressure 2g to 3gCoil impedance 2?Load impedance 3?Playback frequency range 10Hz to 45kHzChannel balance 1dB(1kHz)Channel separation -28dB(1kHz)Compliance 7x10-6cm/dyne(100Hz, 20°C)Needle tip 0.15mm square refined-contact solid diamond needleWeight 30g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Der Acoustic Research A-07 Integrated Amplifier ist ein High-End HiFi Verstärker mit einer Leistung von 300 W. Dieses seltene Produkt verfügt über verschiedene Audioeingänge wie AUX, Phono/Turntable, DIN und Pre Out, um eine vielseitige Nutzung zu ermöglichen. Das elegante Design in Schwarz macht diesen Verstärker nicht nur zu einem leistungsstarken Audio-Gerät, sondern auch zu einem stilvollen Blickfang in jedem HiFi-Setup. Bitte nicht falsch verstehen aufgrund des hohen Alters, an Bastler zu verkaufen. Gerät ist über 30 Jahre alt. Zustand. Siehe Bilder war im Strom! Kein Garantie, Keine Rücknahme.

fidelity-research FR FR-7f Shell Integrated Stereo Moving Coil MC Cartridge #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. The cantilever is not broken or bent. Stylus tip and damper are in good condition. Original case included. Overview Shell-integrated MC cartridge, an improved version of the FR-7. It uses a unique push-pull power generation system with a 2-magnet, 4-pole magnetic circuit.This system generates power at four points, so that a large output voltage can be obtained even with a low-impedance coil. In addition, although the general system generates canceled current in the generator circuit, the FR-7fs magnetic circuit can generate positive output in the opposite direction even in the region where canceled current occurs. This improves the phase and crosstalk characteristics as well as the electrical conversion efficiency, resulting in higher output power. A samarium-cobalt magnet is used as the magnetic circuit material. These magnets have a higher coercive force and are less likely to self-demagnetize than ordinary alnico magnets, thus maintaining the initial characteristics of the magnetic circuit for a long period of time. The generator coil uses a completely air-core coil without a winding frame, which prevents unwanted magnetic materials from moving within the generator field and fundamentally eliminates distortion of the reproduced signal. The effective mass of the resonator is also reduced to about 2/3, resulting in a smaller mechanical impedance in the high frequency range. For the needle tip, a unique refined-contact needle made of solid 0.15 mm square diamond is used.The new method of using a refined contact needle combines the advantages of a line-contact needle with those of an oval needle, making it less susceptible to adverse effects (noise, etc.) caused by the warping of the disc and dust in the sound groove. The new needle is less susceptible to the adverse effects (e.g., noise) of warpage and dust in the sound grooves of a disc, and generates very little scratch and surface noise, resulting in a clear and uninterrupted playback sound. A special aluminum alloy cantilever is used for the cantilever.This is a straight cantilever made of a highly corrosion-resistant special aluminum alloy with optimum heat-hardening treatment (ceramic treatment) to minimize the moment of inertia and deflection during high-speed movement. The leading part of the string holder extends to the front of damper B, which makes the fulcrum position clearer. This clarifies the cantilever vibration fulcrum position and minimizes the cantilever vibration distance variation at each frequency.In addition, the string wire used to tension the cantilever is made of a material with a very high spring coefficient and little change over time, which contributes to the improvement of the square wave characteristics. A dual damper system is employed, with two layers of dampers with different rubber coefficients to effectively dump the mid-high and mid-low frequencies of the vibration frequency respectively, enabling ideal tracing over the entire reproduction frequency range.In addition, the rubber coefficients of damper A and B are different to reduce the total effect of temperature on tracing performance, mechanical impedance characteristics, and reproduced sound. To solve the problem of coil lead wires vibrating with the cantilever, coil lead wires are inserted and crimped between dampers A and B to eliminate unwanted power generation by the lead wires. The head shell is shaped to completely remove dead space that could cause parasitic vibration, which is detrimental to sound quality. The shell is made of a special aluminum alloy, which is impact-machined (cold-forged) to further increase rigidity and prevent split resonance. The cartridge body is made of epoxy resin, which was selected through careful audibility tests. To improve the lack of strength caused by rattling between the arm and connector section, a special stainless steel locking plate is used in place of the conventional guide pin. This allows for a more integrated connection with the arm, and the level can be maintained correctly. Specifications Type: MC CartridgeOutput voltage 0.15mV(3.54cm/sec., 45?)0.2mV(5cm/sec., 45?)Output power 2x10-8W(5cm/sec.45?)Needle pressure 2g to 3gCoil impedance 2?Load impedance 3?Playback frequency range 10Hz to 45kHzChannel balance 1dB(1kHz)Channel separation -28dB(1kHz)Compliance 7x10-6cm/dyne(100Hz, 20°C)Needle tip 0.15mm square refined-contact solid diamond needleWeight 30g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Used Audio Research VSI-75 Integrated.Tubes have roughly 400 hours on them.

For Sale - Integra Research RDA-7 Amplifier. If you are looking at this ad you need no explanation as to what this amp is! It is in excellent physical condition. One channel needs repair/replacement and it is priced accordingly. The amp has recently been inspected by Adams Electronics (a $180 fee) and all other parts are functional, I have uploaded the repair invoice indicating it needs a new board for one channel. If you are handy you can repair the specific amplifier channel, or bypass the channel and use 6 channels. Or, you can part it out - there is definitely a market for the amplifier channels and the transformers. Again, it is priced accordingly. Buy with confidence - Please check my feedback! Shipping will be by FedEx Ground and only to Continental USA excluding Alaska. Please contact me with any questions, thank you for looking!

Free eBay listing template designed by dewiso.com Audio Research VSi75 Integrated Amplifier - RRP £7,499 - Customer Trade In Customer Trade In - Very Good Condition - Original Box and Accessories: Tubes, Manual, Power Cable, Remote Features and further details Additional Features: Details: Package Includes (If it isnt mentioned, it isnt included):Tubes, Manual, Power Cable, Remote Contact us We can be contacted at any time through eBay messages if you have any questions, comments or product requests. We will respond to you within 24 hours and do our best to help you out! We encourage our customers to contact us on 01707 320788 with any questions or concerns! Wed like to be sure you are completely satisfied with your purchase. Payment Payment to be made by Ebay, Paypal, Cash or Banks Transfer (Call Nintronics to organise) Shipping Items <20kg will be shipped via DPD local on a next day delivery. Items >20kg will be shipped on a next-day pallet shipment. To discuss a hand delivery or installation, call Nintronics on 01707 320788 Disclaimer Items will be shipped with the accessories mentioned on the listing, Nothing more! If it isnt mentioned in the listing, it isnt included. We will not accept returns for items due to missing items if they arent listed with the item.

.I assume if your looking you know the sound and build quality that this amp represents. Its been the highlight of my main system for the last 20 years and sounds as good today as when new.. Its been in a non-smoking home and was housed a dedicated audio cabinet and was primary used for music. I had bi-amped my main speakers (Mcintosh LS360s) using 4 of the channels and the other three for the center and rear speakers. There is a small area on the top corner of the left front panel that has cosmetic damaged when it was shipped to me as well as one of the channels speaker terminals that was pushed in very slightly. I have included pictures of each area, none of which affected the operations in any way. I had zero plans to ever move it out of my system but came across a BAT VK-6200 at a price I couldnt pass up. It is clear that both amps were designed by the same individual Victor Khomenko.The RDC-7 was $5000 new and was still half price of anything that BAT produced. Its a very large and heavy amplifier. Would prefer local pick up and would be willing to meet someone within a reasonable driving distance https://www.hifidiprinzio.it/files/2014/09/201409262035121.pdf RDA-7 7-Channel Power Amplifier • THX® Ultra Certified • THX Surround EX™ Capable (7 channels) • Low-Negative Feedback Design • Balanced XLR Inputs • Symmetrical Bipolar Topology • High-Current Driver Stage • 3 Gain Stages • Wide Range Design • Massive, High-Quality, Dual 1 kVA Toroidal Transformers • 600 Joules of Energy Storage • Over 1000 Watts of Total Output Power (150W x 7 at 8 ohms, all channels driven) SPECIFICATIONS 150 W+150 W (0.1% THD)(8 ? 20 Hz-20 kHz FTC) 300 W/ch (0.1% THD)THD (at Rated Power) 0.03% (all channels) GENERAL Dimensions (W x H x D) Weight 17-11/16? x 7-11/16? x 23-7/16? 450 x 195 x 596 mm 112.41 lbs. 51.0 kg

Overture Ultimate Home Electronics, located in Wilmington, Delaware, is America’s premier high-end audio, home theater, and home electronics store. The equipment we are offering on Ebay is either equipment we have had on demo at Overture, or equipment that has been taken in by Overture as a trade-in from our customers. All of the equipment has been thoroughly checked by our technicians to make sure it works properly. BEFORE YOU BID SEE IF YOUR STATE IS ON THE TAX LIST. EBAY IS NOW CHARGING TAX.Up for auction is an Audio Research VSI 75 Integrated Amp, used and tested. Comes with box, packaging and power cable.

Audio Researchs award winning VSi60 was a great Integrated amplifier, however advancements in technology helped ARC make the new VSi75 even better. The VSi75 received a brand new transformer specifically designed for the KT150 tubes. A number of the components from the REF75 were brought into the VSi75 to take its musicality to the next level. Even the power supply caps were doubled to improve headroom. With tremendous detail and resolution its able to take your listening to new places. Its all-in-one design makes creating a great music system simple. This integrated is clean and well cared for. Includes the remote, manuals, accys and original box. FEATURES -Brand new high performance power supply5 inputs80 Watt/ ch max outputMatched KT150 Power TubesRemote Control SPECIFICATIONS -POWER - 75 Watts/ch rated (4-8 Ohms)FREQUENCY RESPONSE - 1Hz - 70HzSENSITIVITY - .55V RMS INPUTS - (5) RCATUBES - (2) KT150, (2) 6H39 DIMENSIONS - (LxWxH) 16.25 x 14.5 x 9.25WEIGHT: 36.5 Lbs IN THE BOX -Owners ManualOriginal Remote controlOriginal power cordOriginal double box CONDITION - This unit is in excellent condition. Fully tested and operational. SHIPPING - We ship worldwide with UPS, Fed-Ex and various truck freight lines. All items are packed and padded with care if the original packaging is deemed insufficient. We know how exciting it is to anticipate the arrival of new gear and we want your item to arrive in the same condition it left our facility. Current retail price - $10,000

Audio Researchs award winning VSi60 was a great Integrated amplifier, however advancements in technology helped ARC make the new VSi75 even better. The VSi75 received a brand new transformer specifically designed for the KT150 tubes. A number of the components from the REF75 were brought into the VSi75 to take its musicality to the next level. Even the power supply caps were doubled to improve headroom. With tremendous detail and resolution its able to take your listening to new places. Its all-in-one design makes creating a great music system simple. This integrated is clean and well cared for. Includes the remote, manuals, accys and original box. FEATURES -Brand new high performance power supply5 inputs80 Watt/ ch max outputMatched KT150 Power TubesRemote Control SPECIFICATIONS -POWER - 75 Watts/ch rated (4-8 Ohms)FREQUENCY RESPONSE - 1Hz - 70HzSENSITIVITY - .55V RMS INPUTS - (5) RCATUBES - (2) KT150, (2) 6H39 DIMENSIONS - (LxWxH) 16.25 x 14.5 x 9.25WEIGHT: 36.5 Lbs IN THE BOX -Owners ManualOriginal Remote controlOriginal power cordOriginal double box CONDITION - This unit is in excellent condition. Fully tested and operational. SHIPPING - We ship worldwide with UPS, Fed-Ex and various truck freight lines. All items are packed and padded with care if the original packaging is deemed insufficient. We know how exciting it is to anticipate the arrival of new gear and we want your item to arrive in the same condition it left our facility. Current retail price - $10,000

For sale is an Integra Research RDC-7.1 A/V processor preamplifier with its remote, manual, a power cord, and original box and packaging in very good condition. Our tech has confirmed that all inputs, outputs, and internal components are functioning properly and everything is in perfect working order. Cosmetically this item is in great shape with only a few minor blemishes on the front and general signs of use along the edges. However, it has a fantastic overall appearance and is fully functional. This is a great addition for someone looking to step up their home theater/HiFi setup in an affordable yet quality way. Phenomenal performance & fidelity, excellent trigger options, HDMI (version 1) & I.Link, attractive fit & finish, as well as upgradeable architecture - audioholics.com SPECIFICATIONS: Formats: THX Ultra-approved with Dolby Pro Logic, Dolby Digital (with THX EX), DTSAudio inputs: 5 digital coaxial, 1 AC-3 RF digital coaxial, 3 digital TosLink, 9 analog L/R, 1 analog 7.1-channel throughput, 1 RIAA phonoVideo inputs: 6 composite, 6 S-video, 3 componentAudio record outputs: 2 tape, 2 video recorderAudio outputs: unbalanced (RCA) and balanced (XLR) for each L/R, Center, Subwoofer, L/R surround, and L/R rear surround (2 outputs each for unbalanced L/R and Center), Zone 2 L/R, 1 digital coaxial, 1 digital TosLinkAdditional inputs/outputs: RS-232 port, A&B assignable 12V trigger, Onkyo RI remote repeater output, main and Zone 2 remote repeater inputsAnalog input/output impedance: 50kohms/470ohmsSignal/noise: Phono, 80dB (IHF A, 5mV input); CD/Tape, 100dB (IHF A, 0.5V input)FM sensitivity: 17.2dBf, 2.0µV (75ohms IHF)Voltage requirements: 120V, 60HzDimensions: 1711/16 x 711/16 x 175/16 (WxHxD)Weight: 35.7 lbs. Decibel Audio is a retail store and custom installation business in the Wicker Park neighborhood of Chicago. We have serviced the Chicagoland area with new, used and vintage equipment for over 20 years. Visit our brick and mortar store at 1429 N Milwaukee Avenue, Chicago, IL 60622. We are authorized dealers for AKG, Audioengine, Audioquest, Bellari, Bluesound, B&W, Cambridge Audio, Cary Audio, Clearaudio, Cleer headphones, Dali, Denon, Draper Screens, Dynaudio, Grado, Harbeth, Hegel, Iso Acoustics, Jolida, JBL Pro, James Loudspeaker, KEF, KLH, Lehmann Audio, Marantz, Music Hall, NAD, Ortofon, Parasound, Pro-Ject, PSB Speakers, Plateau, Rega, Rogue Audio, Russound, SONOS, Samsung, Skylan, Vicoustics, Yamaha, and more. All shipping is via UPS or USPS as noted in each listing, unless other arrangements are made. Buyer is responsible for reviewing cosmetic condition detailed in photos before bidding. You are welcome to pay with Visa, MC, Discover, AmEx, Etc. We prefer Paypal for international bidders. Local customers are welcome to view and pick up auction items during store hours. All customers must pay Illinois Sales Tax if picking up in store. Illinois residents please add 10.25% sales tax for shipped items.

Acoustic Research AR07 High End Integrated Amplifier AR07 (Faulty). Excellent cosmetic condition. Cherished amplifier. No longer functional due to accidental short cct. Very high quality expensive amplifier when new. Would make excellent donor or worth repairing. Can courier for £15. Or pick up in CR6 Surrey

Acoustic Research A-07 Integrated Amplifier -Verstrker. Voll funktionstchtig! Nach wie vor - erste Klasse! DatenBearbeiten Allgemein Hersteller:Acoustic Research Modell: A-07 Typ: Vollverstrker Baujahre: 1991 - 1994 Hergestellt in: Taiwan Farbe: Schwarz Fernbedienung: ja, entweder ber Tuner T-06 R oder optional RC-03 Leistungsaufnahme: maximal 300 W Abmessungen (BxHxT): 430 x 93 x 354 mm Gewicht: 8,9 kg Neupreis ca.: 998 DM Option Fernbedienung: 60 DM Anschlsse Phono (MM/MC) CD AUX TAPE1/TAPE2 CD VCR1/VCR2 Kopfhreranschluss 3,5 mm Jack 2 Lautsprecherpaare getrennt schaltbar Vor-/Endstufe trennbar: JA Technische Daten Dauerleistung: 2 x 60 W an 8 Ohm 2 x 95 W an 4 Ohm Impulsleistung: 2 x 90 W an 8 Ohm 2 x 140 W an 4 Ohm Frequenzbertragung: 20 Hz - 20 kHz -3dB Klirrfaktor: 0,03% Dmpfungsfaktor: 100 Eingangsempfindlichkeit: 2,3 mV (MM) 0,18 mV (MC) 150 mV (line) Signalrauschabstand: 85 dB (MM) 75 dB (MC) 100 dB (line) Kanaltrennung: 70 dB (line) Klangregelung Bass 6,5dB ( 100 Hz ) Hhen 6,5dB ( 10 kHz ) Muting-Schalter Tone-Defeat-Schalter

fidelity-research FR FR-7f Shell Integrated Type Stereo Moving Coil MC Cartridge Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. The cantilever is not broken or bent.Stylus tip and damper are in good condition. w/ Original case. Specifications Type? MCOutput voltage: 0.15mV (3.54cm/sec., 45°), 0.2mV (5cm/sec., 45°)Output power: 2x10-8W (5cm/sec., 45°)Needle pressure: 2g to 3gCoil impedance: 2?Load Impedance: 3?Playback Frequency Range: 10Hz to 45kHzChannel Balance: 1dB(1kHz)Channel Separation: -28dB(1kHz)Compliance: 7x10-6cm/dyne (100Hz, 20°C)Needle tip: 0.15mm square refined-contact solid diamond needleWeight: 30g Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Free eBay listing template designed by dewiso.com Audio Research VSi75 Integrated Amplifier - RRP £7,499 - Customer Trade In Customer Trade In - Very Good Condition - Original Box and Accessories: Tubes, Manual, Power Cable, Remote Features and further details Additional Features: Details: Package Includes (If it isnt mentioned, it isnt included):Tubes, Manual, Power Cable, Remote Contact us We can be contacted at any time through eBay messages if you have any questions, comments or product requests. We will respond to you within 24 hours and do our best to help you out! We encourage our customers to contact us on 01707 320788 with any questions or concerns! Wed like to be sure you are completely satisfied with your purchase. Payment Payment to be made by Ebay, Paypal, Cash or Banks Transfer (Call Nintronics to organise) Shipping Items <20kg will be shipped via DPD local on a next day delivery. Items >20kg will be shipped on a next-day pallet shipment. To discuss a hand delivery or installation, call Nintronics on 01707 320788 Disclaimer Items will be shipped with the accessories mentioned on the listing, Nothing more! If it isnt mentioned in the listing, it isnt included. We will not accept returns for items due to missing items if they arent listed with the item.

Used FIDELITY-RESEARCH FR-7 MC Cartridge Shell Integrated MC Cartridge RareInternational Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.International Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.

Integra Research RDC-7 + RDV-1 - Silber. Beide voll funktionsfähig , wegen Hobbyaufgabe abzugeben.Kaufpreis damals : RDC-7.1 AV-Controller 6000,- €RDV-1.1 Universal DVD-Player 5300,- €1 Hand nur Abholung , Gesamtgewicht Ca. 30 kgAusführliche Beschreibung findet ihr hier : https://www.areadvd.de/hardware/2005/integra_research.shtml

Wonderful amp! I have years of history with ARC and this is the best ARC integrated I’ve ever heard, and one of the best pure amps of any variety I’ve ever had in house. I purchased this amp brand-new/sealed in April from an authorized ARC dealer, and as you can see have <200 hours on it since. I love the amp, but haven’t used tubes in my main home system for a number of years, and it has been a real annoyance to the rest of my family, who don’t want to deal with warmup—they just want to click and go. I’ve been using it on weekends, switching back to SS for the week when they are more likely to use it without me being around, but I think it’s best to move back to SS full time. I don’t have room for a 2nd system, so to the next owner it goes. Absolutely as-new, with the new ARC cerakote remote to boot. Includes amp, remote, bias tool, factory tubes with less than 200 hours, original box and packaging, and sales receipt from authorized ARC dealer. Shipping is $$$ due to size of the box (ARC’s packaging is legendary!) so I’ve priced it flat at about 1/2 actual cost, I’ll pick up the rest.

Integra Research RDC-7 + RDV-1 - Silber. Beide voll funktionsfähig , wegen Hobbyaufgabe abzugeben.1 Hand nur Abholung , Gesamtgewicht Ca. 30 kg

For sale is a used Integra Research RDC 7.1 in excellent condition. The unit has been tested and everything is functional as new. I am the original owner and have been using this with the Integra Research RDA 7.1 power amplifier. This sale comes with original user guide, remote control, warranty card, and original box.

Description of itemThank you for visiting! Our shop is 100% Authentic item. If you have any questions, please be free to ask us.  Have a great shopping on ebay! Paymentwe accept payment only through ebay Managed Payment. Shipping-Japan Post: 5-20 days to arrive -DHL: 5-10 days to arrival *We will ship the item by Japan post or DHL.  If you need expedited shipping, please let me know. I will ask you about extra payment.  Depending on the size and weight after packing the items, The shipping method may change depending on your location. **If you live in a remote area, We might ask extra charge for intenrational shipping. Please contact us for additional charges Shipping is only available to the address registered on ebay. Please note that any address not registered in ebay is not acceptable to ship. Shipping is available from Monday to Friday. **If you live in a remote area, We might ask extra charge for intenrational shipping. Weekends are not available because post office is closed.Term of sale-Return We accept product return within 30days from delivery date but product should be in original position and not in damaged condition,the return shipping charges will be buyer responsibility. -International Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.