This eBay Ad is for Normal 0 false false false EN-US X-NONE X-NONE a near perfect pair of Infinity RS6 Infinity loudspeakers - with a sweet sound-stage. The beautiful real OAK wood has no corner dents, no mar of Midrange Polydomes, the EMIT ribbons are fully intact, & OEM+ Woofers were re-foamed. When 1st seen:1) Excellent cabinets, Bad standard woofer Surrounds had Foam Rot2) Almost entirely free from wood blemishes and/or other visual defects 3) Apparent they have been played / used with care, thus $$++ just to buy 4) Used in a smoke free home, powered by a sweet Pioneer 626 Receiver. John - sofar has avoided to sell that Prize – Eyes bugg’in-on’it, still. Re: Pickup - To START - 5 miles is not a limit, near Denver, or I25 & 104th. On Price & Eval - is an Audition needed or desired? Only with an in person listening a go / no-go; if dissatisfied, you can refund. Re: Ship – see below Refurbishment: as an OEM purist. Had to seek a suitable Woofer, for months.Care in handling, re-seating exact screws & their threading, Cap checks, etc. Chose to re-foam Woof#1 – which was a good job, used shim method. Done 100s Then replace Woof#2 due to slight breakup @power - maybe the spider? [Purchased a Pro re-foamed 902-5030 from an RS7b OEM doner.] original woofers with skilled surround re-furbs - not swap outsCabinets given a good vacuuming, noticed their beauty, hard to find a scratch. Really – seen the bottom pictures Cleaning crevices by Q-tips / microfiber to collect dust / smutz in various spots Considered - then a light preservation coat of Liquid Gold. Wow! Grain revealed+ Weight about 30 pounds each, at 22”t x 13.5”w x 10”d. (or 56 x 34 x 25.5 cm) Speakers were built in 1985 +/- 1Yr, an in person pickup / audition preferred Suggested for Amp: 35-100 Watts per L&R Frequency range: 45 Hz - 32 kHz Have read Substitute Woof >= 3Hz lower F(r) Crossover Freq: 600 Hz, 4kHz <--- Notice big Dome MidRange has a bit lower Cross point? These also have notable Rapid Acceleration for crispness; read such very-fast Response Time, is so vocals attack/decay stronger. The EMIT tweeter with its planar design was revolutionary then. It pairs well with dynamics of MidRangess 4kHz cross point to a single ended ribbon. EMIT = Electro-Magnetic Induction Tweeter, which is a push-pull ribbon transducer with an etched voice-coil in a ribbon. Accuracy... Shipped: Please ask your ?s in eBay message, some hours to pack This would be a plastic slip, Full X-Y wrap, cardboard front cover Then individually custom boxed. Next a 1-2” styro-foam pad, cut and fit, on top and bottom, then an outer Cardboard Box per Speaker. 2++ layers, 2 packages, each Insured. Need even more info? Read on... First... Open to ?s One Review: They sound really good, and dont need a subwoofer unless you want to really pound bass. IMHO: on “Bass” this Set has the Stronger Stock 9 flange Woofer with a larger diameter 3.5 vs. 3.0 magnet which was an OEM option or a per Spec OEM substitute 902-5030 vs. standard 902-4976 with same grey wide flange frame and look. In a later side by side picture One can see the larger magnet of OEM Substitute 902-5030 with a measured impedance of 3.5 Ohms and 0.98mH vs. Stock Standard 902-4976 which as a 3.7 Ohms and 0.88mH impedance or about 10% shift of the low-pass crossover & power a bit more bass pump. Drivers: …alone, average to replace all is about $420 total $65 per EMIT planar Tweeter $75 per PolyDome MidRange (no dents) $70 per 8.25” Woofer - ONLY if a Re-Foamed 902-5030 Standard 902-4976 -$20, Substitute 902-5030 is less common (bigger magnet) $210 per Checked on eBay for some time for buys. $518 MSRP in 1985 is per USinflationCalculatorDOTcom or ~$1600 today Other sets have sold in 450 (130 s/H) to 550 range - condition a subjective swing. The Ask price is $518 / $1600 being <= 1/3 of original. TY for Looking - Notice: Ship price already includes Handling of $60. Ships to USA. Basement clear-out - Audio items & Loud Speakers. Selling collections on Downsize. There are other cool Audio, Speakers, and electronics at solar_home eBay pages