Technics EPA-500 [ EPA-A501H EPA-B500 ] Dynamic Damping System Tone Arm #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed. The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. Operation has been confirmed with the following contents.Output from both channels.Lifter descent speed.Height adjustment, etc. There is no problem in operation. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. *The black pedestal of the base is for photographic purposes only and is not included. Overview System tone arm set including arm base EPA-B500 and arm unit EPA-A501H. EPA-B500The EPA-B500 is an arm base to which an arm unit can be attached. The EPA-B500 uses a structure that allows arm units to be interchangeable, while employing a unique gimbal suspension bearing structure that is used in Technic Tone Arms.The gimbal suspension system is a four-point support system using high-precision pivots and ball bearings, and the axial centers of the horizontal and vertical rotation axes intersect at a single point to achieve a high initial sensitivity of 7 mg or less for both horizontal and vertical rotation.The bearing is supported by a precision zinc die-cast base to thoroughly suppress external vibration. Furthermore, a reliable sliding connector is used for the arm unit and arm base to achieve a self-cleaning effect when replacing the unit. An arm height adjustment mechanism with a 12-way helicoid is provided for highly accurate arm height adjustment. The output cord has low DC resistance of 39.5m?/m and low capacitance (41.5pF/m) for excellent transmission characteristics. EPA-A501HThe EPA-A501H is an arm unit for high compliance cartridges. This arm unit inherits the functions of the EPA-100 and uses a unique dynamic damping mechanism for the balance weight, which improves the low-frequency resonance sharpness of the arm unit by more than 6dB compared to a normal arm. Furthermore, unlike the oil dump damping system, the damping characteristics below the low-frequency resonance frequency are improved without increasing the mechanical impedance of the low-frequency range. This dramatically reduces resonance peaks and improves low-frequency characteristics by selecting an arm unit that matches the cartridge. Titanium nitride (TiN), a lightweight and strong titanium that has been specially nitrided to increase rigidity, is used as the pipe material for the arm unit. This eliminates partial resonance of the tone arm, and the ideal distribution of mechanical strength reduces weight by 85% compared to conventional aluminum pipes, while achieving mechanical strength 1.6 times greater. Specifications Model: System tone arm

Technics SL-1015 PlattenspielerLaufwerk SP-15 / Basis EPA-500 / Haubegeprüfte Ware vom Händler mit einem Jahr Gewährleistungan dem Gerät ist alles voll funktionstüchtig - es gibt von der technischen Seite keine Beanstandungallgemein gibt es typische, altersbedingte und normale Gebrauchsspuren - guter Gesamteindruckdie Haube weist einige Mängel auf - es gibt Schleif- und Kratzspuren - außerdem mit Rissdie bereitgestellten Fotos zeigen den angebotenen Artikelaußerdem zeigen sie die Bestandteile der Lieferungweitere Artikel finden Sie in meinem Shop

DescriptionWelcome to J-FORESTAR MARKET !!Thank your for watching our page!!?Condition:USED(Good)It has been verified to work.?This is a 100% Authentic item from JAPAN.?If you have any questions or request about items, please feel free to ask us.PaymentWe accept managed payments.ShippingThis item is Shipped from Japan by DHL or FedEx.We usually ship out your order within 5 working days after receiving your payment. It usually takes about 3 to 6 days after the shipment is completed.(Please note that delays may occur depending on the season and weather.)About UsWe are located in Japan.Its our pleasure to make you happy by proposing our recommend item.If you have any questions or request about items, please feel free to ask us.International Buyers - Please Note: ?Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility. ?Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying. ?These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges. ?We do not mark merchandise values below value or mark items as “gifts” - US and International government regulations prohibit such behavior.

Technics EPA-500 [ EPA-A501H / EPA-B500 ] Dynamic Damping System Tone Arm Domo Arigato! Welcome, Thank you for your visit. Description Universal type system tone arm that combines the EPA-B500 tone arm arm base unit and the EPA-A501H tone arm unit. The EPA-A501H is an arm unit for high compliance cartridges. Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. *The black pedestal of the base is for photographic purposes only and is not included. Specifications < Tone Arm Base Unit EPA-B500 >Type: Arm replacement type arm baseBearing structure: Gimbal suspension systemHeight adjustment range: 42mm-62mm (from base mounting surface to pipe center), helicoid: 20mmInitial sensitivity: 7mg or less (horizontal, vertical)Output cord DC resistance: 39.5m?/mOutput cord capacitance: 41.5pF/mArm base mounting hole: ?62mm < Tone Arm Unit EPA-A501H >Model: Dynamic damping type arm unitArm pipe: Titanium nitride (TiN) tapered pipeEffective arm length: 250mmArm rear length range: 68mm~85.5mm (from arm fulcrum)Overhang: 15mmHorizontal tracking error angle: +1?6(inner circumference of 30cm record), +2?6(outer circumference of 30cm record)Arm effective weight? 8g(without cartridge)Compatible cartridge weight: 5g~7gApplicable Cartridge Compliance: 10 to 14x10-6cm/dyne (Dynamic 100Hz) Accessories PHONO cableArm fixing screws x 3Instruction Manual (copy) (Japanese)Template (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Audio Mai 1980. Im Heft sind unter anderem folgende Themen, Tests bzw. Gerätebesprechungen zu finden. Cassettenrecorder: Akai GX-F 90 JVC KD-A 77 Offener Brief an Günter Verdin Plattenspieler: Micro RX-5000 Tonarme: Audio Technica AT-1100 Micro MA-707 SME 3009/III S Technics EPA-500 Vollverstärker: Dual CV 1200 Grundig V 2000 Harman/Kardon HK 503 Pioneer SA-608 Sony TA-F 40 Technics SU-8055 Anlagenberatung: HiFi-Anlage zusammenstellen Musik: Wolle Kriwanek Gordon Lightfoot Ist Donald Duck musikalisch? Viele ausführliche Plattenbesprechungen Anzeigen aus der damaligen Zeit und mehr Falls nicht ausdrücklich erwähnt, sind die Hefte immer ohne CD und sonstige Beilagen. Die Hefte sind auch alle mehr oder weniger gebraucht. Es können evtl. Markierungen bei der Announcen vorhanden sein. Auch ist vereinzelt der Adressaufkleber noch ganz bzw. teilweise vorhanden, es können auch noch Reste am Heft sein. Preisausschrauben wurden in der Regel ausgefüllt bzw. auch ausgeschnitten und sonstige Vorlagen zum Herausschneiden sind in der Regel entfernt. Ab und zu ist auch eine Plattenkritik ausgeschnitten. Abholung möglich oder Versand auf Kosten des Käufers. Versand erfolgt nach Zahlungseingang. Bezahlung muss innerhalb einer Woche erfolgen oder nach Vereinbarung mit mir. Abholung bevorzugt. Erfüllunsort ist 69115 Heidelberg Nach der allgemeinen Regelung des Bürgerlichen Gesetzbuches (BGB) trägt grundsätzlich der Käufer das Risiko des Verlusts und der Beschädigung der Ware auf dem Transportweg (§ 447 Abs.1 BGB). Der Versand der Ware geschieht also auf Risiko des Käufers. Dieses Angebot ist privater, nicht gewerblicher Natur. „Verkauf gebrauchter Ware von Privat“. Keine Haftung für Tippfehler. Mit der Abgabe eines Gebotes verzichten Sie auf die gesetzlichen Garantie- und Gewährleistungsansprüche sowie auf Ihr Rückgaberecht (ausser bei Abholung).

Superb TECHNICS EPA-500 Titanium System Tonearm Absolutely pristine example of this very special and versatile system tonearm that comprises EPA-B500 arm base and EPA-A501H interchangeable arm unit, together with original accessory items and fittings. Design and engineering are exemplary and the interchangeable titanium EPA-A500H arm unit specifically provides optimum matching and performance for cartridges of 4.5 to 7.0 grams weight and low to medium tracking force, ie. 1.00 to 2.00 grams. Uniquely the EPA-500 system utilised a number of interchangeable titanium arm units of different effective mass to permit optimum matching for cartridges requiring particular tracking force requirements, ranging from a low of 0.75 to a high of 3.0 grams. Such units are frequently available for purchase on eBay and elsewhere.---------------------------------------------------------------------------------------------------------------------NB: I will be listing various EPA-A501 interchangeable arm units from my collection in the coming months--------------------------------------------------------------------------------------------------------------------- Technics engineers really knew their field: their skill and flair is clearly evident in EPA-500s revolutionary design, which incorporates many outstanding technical features and attributes, including:tapered titanium-nitride arm tube for maximum rigidity to weight ratio and lowest effective massultra precise, minimum friction gimbal bearing suspension for surest tracking performance under all playback conditionsdyno-magnetic damping system to control tonearm/stylus resonance for surest tracking of lowest bass frequenciesmicrometric VTA adjustment to set optimum tonearm high for purest playback of treble frequenciesfrictionless and precise antiskating device for accurate and predictable arm-bias compensationoutput cable with unique combination of low resistance as well as low capacitance for optimum signal transferSecifications: Effective length: 250 mmOverhang: 15 mmTracking error angle: +1.1 deg @ inner groove, +2.1 deg @ outer grooveEffective mass: 8 gSuitable cartridges: 4.5 - 7.0 grams weight, 10 - 14 cu (100 Hz dynamic)Height adjustment: 44 - 64 mm (base mounting to cartridge mounting surface)Pivot suspension: axis frictions less than 7 mgMaximum height: 88 mmMaximum rear overhang: 85.5 mmBase underhang: 64 mmMounting hole: 62 mm diameterMounted weight: 790 gramsOutput cable: 1.25 m long, 39.5 m?/m, 41.5 pF: gold plated RCA phono plugs Owner reviewsTechnics EPA 500 by BrownlowI did not know what to expect, however, I am one happy fellow. Absolutely excellent, if you are in the market for a used tonearm, Im sure you wont be disappointed with listening with one of these. by Peter4103Absolutely superior tonearm. I have had my share of tonearms, but this beauty is certainly the best so far. And very easy to install and use. Make sure to follow the tonearm compliance, which is easily found in the chart on the last page of the manual. There are various arms for various different carts. To swap the tonearm is as easy as removing a headshell. However, mounting a new cart is a bit more tricky due to the fact that the whole tonearm is a bit more difficult to handle than just the headshell. But once installed, it is a great experience. The EPA 500 is very hard to find though in good condition. by hullevadIt makes the patience and effort worth matching cartridge and arm, if possible.I were on the lookout for a M armtube for 5 years and got a NOS, matches my Audio Technica ART 7 perfectly. Armtube Cu must match that of the cartridge exactly according to japanese data (100hz). The best arm? Yes when matched with a proper cartridge. by marco_63Superb tonearm! by Ronald de CarvalhoFabulously made and superbly performing tonearm from one of Japans most accomplished and innovative makers of audio equipment. by florestanSuperb tonearm, executed with outmost care in every details, from the lock system to the antiskating device. The decoupled and damped counterweight is a thing of beauty and really is effective. This arm deserve to be used in any very high quality turntable, Technics SP10 of course but also other maker: in my current turntable it is really working beautifully as it did on a friends Micro Seiki. The possibility to interchange between a number of arm units to accommodate cartridges of different weight & compliance is also very interesting and as far as i know only offered now by Moerch. Very highly recommended.

You are looking at the *Technics EPA-100MK2/MKII EPA-500 Original Genuine Phono Cord Cable Condition: May have a few minor signs of use. *Dont forget to check our other items to view more cool stuff. Well be glad to combine shipping! Express Shipping : 3 - 10 days. Standard Shipping : 7 -14 days. Economy Shipping : 10 - 28 days. Duties and Local Tax are not included.These charges are the buyers responsibility. if you have any question, please feel free to contact me!

Superb TECHNICS EPA-500 Titanium System Tonearm Absolutely pristine example of this very special and versatile system tonearm that comprises EPA-B500 arm base and EPA-A501H interchangeable arm unit, together with original connecting cable and installation fittings. Design and engineering are exemplary and the interchangeable titanium EPA-A500H arm unit specifically provides optimum matching and performance for cartridges of 4.5 to 7.0 grams weight and low to medium tracking force, ie. 1.00 to 2.00 grams. Uniquely the EPA-500 system utilised a number of interchangeable titanium arm units of different effective mass to permit optimum matching for cartridges requiring particular tracking force requirements, ranging from a low of 0.75 to a high of 3.0 grams. Such units are frequently available for purchase on eBay and elsewhere.------------------------------------------------------------------------------------------------------------------------------NB: I will be listing various EPA-A501 interchangeable arm units from my collection in the coming months------------------------------------------------------------------------------------------------------------------------------ Technics engineers really knew their field: their skill and flair is clearly evident in EPA-500s revolutionary design, which incorporates many outstanding technical features and attributes, including:tapered titanium-nitride arm tube for maximum rigidity to weight ratio and lowest effective massultra precise, minimum friction gimbal bearing suspension for surest tracking performance under all playback conditionsdyno-magnetic damping system to control tonearm/stylus resonance for surest tracking of lowest bass frequenciesmicrometric VTA adjustment to set optimum tonearm high for purest playback of treble frequenciesfrictionless and precise antiskating device for accurate and predictable arm-bias compensationoutput cable with unique combination of low resistance as well as low capacitance for optimum signal transferSecifications: Effective length: 250 mmOverhang: 15 mmTracking error angle: +1.1 deg @ inner groove, +2.1 deg @ outer grooveEffective mass: 8 gSuitable cartridges: 4.5 - 7.0 grams weight, 10 - 14 cu (100 Hz dynamic)Height adjustment: 44 - 64 mm (base mounting to cartridge mounting surface)Pivot suspension: axis frictions less than 7 mgMaximum height: 88 mmMaximum rear overhang: 85.5 mmBase underhang: 64 mmMounting hole: 62 mm diameterMounted weight: 790 gramsOutput cable: 1.25 m long, 39.5 m?/m, 41.5 pF: gold plated RCA phono plugs Owner reviewsTechnics EPA 500 by BrownlowI did not know what to expect, however, I am one happy fellow. Absolutely excellent, if you are in the market for a used tonearm, Im sure you wont be disappointed with listening with one of these. by Peter4103Absolutely superior tonearm. I have had my share of tonearms, but this beauty is certainly the best so far. And very easy to install and use. Make sure to follow the tonearm compliance, which is easily found in the chart on the last page of the manual. There are various arms for various different carts. To swap the tonearm is as easy as removing a headshell. However, mounting a new cart is a bit more tricky due to the fact that the whole tonearm is a bit more difficult to handle than just the headshell. But once installed, it is a great experience. The EPA 500 is very hard to find though in good condition. by hullevadIt makes the patience and effort worth matching cartridge and arm, if possible.I were on the lookout for a M armtube for 5 years and got a NOS, matches my Audio Technica ART 7 perfectly. Armtube Cu must match that of the cartridge exactly according to japanese data (100hz). The best arm? Yes when matched with a proper cartridge. by marco_63Superb tonearm! by Ronald de Carvalho by florestanSuperb tonearm, executed with outmost care in every details, from the lock system to the antiskating device. The decoupled and damped counterweight is a thing of beauty and really is effective. This arm deserve to be used in any very high quality turntable, Technics SP10 of course but also other maker: in my current turntable it is really working beautifully as it did on a friends Micro Seiki. The possibility to interchange between a number of arm units to accommodate cartridges of different weight & compliance is also very interesting and as far as i know only offered now by Moerch. Very highly recommended.

Technics has researched the problem of cartridge/tonearm matching and developed the worlds first variable dynamic damping system, used in its EPA-100.By matching the damping characteristics to the compliance and mass characteristics of the cartridge, Technics has succeeded in greatly lowering the low-frequency resonance peak of the cartridge/tonearm assembly. The EPA-500 has further expanded on this concept so that you will now be able to obtain performance from your cartridge by selecting a tonearm with the most suitable effective mass, arm resonance and damping.The EPA500 tonearm features interchangeable arm units, titanium nitride tapered pipe arm, dynamic damping system, Gimbal suspension arm base for various arm units, helicoid height adjustment ranging up to 20mm and minimum bearing friction of 7mg in all directions.SpecificationsBase: arm base with arm unit interchangeabilityPivot construction: gimbal suspension typeArm height range: 42 to 62mmFriction: 7mg vertical/lateralMounting hole diameter: 62mmArm type: interchangeable arm unit with dynamic damping systemEffective length: 250mmMounting distance: 235mmOverhang: 15mmEffective arm mass: 8g (without cartridge)Applicable cartridge weight: 5 to 7gStylus pressure: 0.75 to 1.75g (2.75g with shell weight)Resonance peak: below 6dB The arm is located in Melbourne, Australia and will be safely packaged for worldwide delivery, local collection is of course welcome. Only the items pictured are included in this listing.

Technics has researched the problem of cartridge/tonearm matching and developed the worlds first variable dynamic damping system, used in its EPA-100.By matching the damping characteristics to the compliance and mass characteristics of the cartridge, Technics has succeeded in greatly lowering the low-frequency resonance peak of the cartridge/tonearm assembly. The EPA-500 has further expanded on this concept so that you will now be able to obtain performance from your cartridge by selecting a tonearm with the most suitable effective mass, arm resonance and damping.The EPA500 tonearm features interchangeable arm units, titanium nitride tapered pipe arm, dynamic damping system, Gimbal suspension arm base for various arm units, helicoid height adjustment ranging up to 20mm and minimum bearing friction of 7mg in all directions.SpecificationsBase: arm base with arm unit interchangeabilityPivot construction: gimbal suspension typeArm height range: 42 to 62mmFriction: 7mg vertical/lateralMounting hole diameter: 62mmArm type: interchangeable arm unit with dynamic damping systemEffective length: 250mmMounting distance: 235mmOverhang: 15mmEffective arm mass: 8g (without cartridge)Applicable cartridge weight: 5 to 7gStylus pressure: 0.75 to 1.75g (2.75g with shell weight)Resonance peak: below 6dB The arm is located in Melbourne, Australia and will be safely packaged for worldwide delivery, local collection is of course welcome. Only the items pictured are included in this listing.