Emotiva BasX A2m 2ch Amplifier (WORKS FLAWLESSLY)- Original box- MINT CONDITION as shown (see photos). Includes power cord and owners manual and original box. Also includes the jumpers for headphone output Circuit Topology The BasX A2m is a stereo power amplifier, with unbalanced RCA analog inputs, a high powered headphone output, and the option of either fixed or variable gain. The A2m combines classical audiophile amplifier architecture, including a carefully designed high current short signal path Class A/B output stage, with advanced microprocessor-controlled monitoring and protection circuitry, and an advanced switch mode power supply, to deliver superb sound quality at a truly reasonable price. BasX A2m Stereo Flex Amplifier Stereo Flex Power Amplifier Circuit Topology The BasX A2m is a stereo power amplifier, with unbalanced RCA analog inputs, a high powered headphone output, and the option of either fixed or variable gain. The A2m combines classical audiophile amplifier architecture, including a carefully designed high current short signal path Class A/B output stage, with advanced microprocessor-controlled monitoring and protection circuitry, and an advanced switch mode power supply, to deliver superb sound quality at a truly reasonable price. Audio Specifications Power Output: (Two Channels Driven) 50 watts RMS per channel; 20 Hz 20 kHz; THD < 0.1%; into 8 Ohms 90 watts RMS per channel; 1 kHz; THD < 1%; into 4 Ohms Power Output (headphone output; normal mode): 8 Ohms: 60 mW / channel 33 Ohms: 200 mW / channel 47 Ohms: 250 mW / channel 150 Ohms: 430 mW / channel 300 Ohms: 440 mW / channel 600 Ohms: 350 mW / channel Power Output (headphone output; direct drive mode -requires internal jumper; USE WITH CAUTION): 8 Ohms: 50 watts / channel 33 Ohms: 12 watts / channel 47 Ohms: 8.5 watts / channel 150 Ohms: 2.6 watts / channel 300 Ohms: 1.3 watts / channel 600 Ohms: 0.6 watts / channel Power Bandwidth (at rated power; 8 Ohm load): 20 Hz to 20 kHz (+ / 0.07 dB) Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dB THD + noise: < 0.02% (A-weighted); ref rated power Signal to Noise Ratio (8 Ohm load): > 112 dB; ref rated power; (A-weighted) Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads) Damping Factor (8 Ohm load): > 500 Input Sensitivity and Gain (for rated power; 8 Ohm load): Fixed gain mode: 0.7 V / 29 dB Variable gain mode: 0.5 V / up to 32 dB Input Impedance: 27 kOhms Input and Output Connections Input Connections: Unbalanced (RCA); one each per channel Speaker Output Connections: Audiophile grade 5-way binding posts Headphone output (front panel): Full sized stereo headphone jack Trigger: Trigger Input: 5 12 V (AC or DC); <10 mA input current required Trigger Output: 12 VDC; can drive any load up to 120 mA Power Requirements 115 - 230 VAC @ 50 / 60 Hz (automatically detected) Front Panel Controls and Indicators Standby: push button Status LEDs:one per channel; blue Status LEDs change to red to indicate a fault condition Standby LED:amber Rear Panel Controls AC Power switch: slide switch selects between On and Auto-On modes Gain switch: slide switch selects between Variable Gain and Fixed Gain modes Internal Settings One pair of internal jumpers can be used to bypass the series dropping resistors to enable full output power to be routed directly to the headphone output (shipped with jumpers OFF) Protection The BasX A2m is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. Mechanical Dimensions:8-1/4 wide x 3 high x 14-1/4 deep (not including connectors)

New in april 2023. I purchased this wonderful amplifier recently but unfortunately it is too deep to fit on my shelf. FYI it is 15 inches deep. 135 WPC @ 8 ohms/ 200 WPC @ 4 ohms. As new in box with remote and manual. Ships to lower 48 USA only

The Emotiva BASX A2 Stereo Powered Amplifier is a high-quality power amplifier that delivers 160 watts of RMS power per channel. This amplifier is perfect for anyone who wants to experience high-quality sound from their home audio system. With its sleek and elegant design, this amplifier is sure to complement any home décor. Its advanced features include a high-quality power supply, gold-plated input and output connectors, and a Class A/B output stage. Whether you're listening to music or watching a movie, the Emotiva BASX A2 Stereo Powered Amplifier is the perfect choice for anyone who wants to experience the best in home audio.

The worlds largest online retailer of pre-owned audio Product DescriptionWho we areWhat we doOur ProcessOur Policies Emotiva XPA-2 Gen 3 Stereo Power Amplifier; XPA2 Product SKU: 53669 Voltage: 120V # of Owners: 1 Service History: None Serial Number: 30C1G0900251 Age: 5 years Tobacco Exposure: No MSRP: $1199 Cosmetic Description: Very good condition with minimal visible cosmetic wear including a couple minor scuffs on the top surface. This item does show a few blemishes but is attractive overall and has been well cared for. What is Included: Amplifier, Manual, Power cable, Factory packaging Other Notes: The XPA-2 is a two-channel audiophile quality power amplifier, and is perfect for powering a superb quality stereo or 2.1 channel music system or, the two critical main channels of a 5.1 channel or 7.1 channel home theater system. - Emotiva Functional Notes: Operational condition of this item is excellent, fully tested and no issues found. Shipping: Cost to ship this item within the contiguous United States is a flat rate of $65- including packaging and insurance. For all other locations including Hawaii, Puerto Rico and Alaska, please request a quote prior to purchase. Items with factory packaging will be double boxed. When factory packaging not available re-usable shipping box with custom injected-foam mold will be used. (for all items over 10 lbs). Note that all items valued over $750 will require a signature upon delivery. Your online source for the best value in new and used audio gear. Visit us online to Buy / Sell / Trade / Consign The Music Room is the largest online retailer of pre-owned HiFi equipment in the world. Headquartered in beautiful Boulder Colorado, The Music Room is a team of 17 strong (and growing) music lovers - all dedicated to one singular mission: delivering the very best online shopping experience in the audio industry - period. We specialize in well-cared for, previously used gear because that is what we are passionate about. We feel that there is nothing more fulfilling than creating a high-performance system on a budget with carefully selected used components, speakers and cables. Our program is safe, secure, fast, fair, hassle-free and highly effective. Visit us online to Buy / Sell / Trade / Consign Buy: Are you looking to get a fair price for your used home audio equipment without all the hassles, headaches, risks and fees? We will appraise your equipment and make you a quick, easy, fair cash offer. Just fill out our “get a quote” form on our homepage to start the process. Sell: We sell in multiple online venues with many (but not all) of our products available in our eBay store. Everything is quality-assured and backed by our best-in-class, satisfaction-guaranteed return policy. Trade: Make your budget go further with a generous trade-in allowance. Let us know what you have available, and we’ll get you the best possible trade-in allowance. We can even assist with shipping & logistics from anywhere in the USA. Just fill out our “get a quote” form on our homepage to start the process. Consign: We offer a hassle-free way for individuals and businesses to liquidate used gear. We’ll handle every step of the process from shipping to appraisals, customer service, fulfillment, and returns: Industry-low rates with no hidden fees Leverage our world-class reputation and get exposure in multiple sales venues - putting your product in front of over 570k monthly shoppers. Our program is Safe, Secure, Fast, Fair, Hassle-Free and Highly Effective. With 100% feedback ratings in every venue in which we sell, you can rest assured that we’ve got your back. Visit us online to Buy / Sell / Trade / Consign Quality Assurance: We offer 15-20 new product listings for sale daily. Each product undergoes an extremely rigorous quality-assurance and listening session by one of our qualified technicians. We understand that buying used audio equipment can be rife with uncertainty and unexpected headaches. Our quality assurance program is informed by a knowledge-base built through delivering over 30,000 used audio products to satisfied customers. We promise to deliver your product in good working order - exactly as described 100% of the time. Support: We don’t just make promises. We stand behind them - your satisfaction is guaranteed. Our support team is ready to help you with any questions you might have before and after the sale. Value: In the never-ending pursuit of high performance, it’s important to stretch your limited budget as far as possible. Used equipment sells for a fraction of new prices, and with a partner like The Music Room you can upgrade any time you like and get most of your money back. There’s simply no better way to maximize a limited audio budget. Packaging: We’ve invested thousands of dollars and countless hours into mastering our state-of-the-art packaging process. Our custom foam-in-place packaging system allows us to safely package almost any item regardless of irregular shapes or sizes. Most importantly, this system provides our customers with a re-usable shipping box which increases the resale value of the product and provides a shipping method for easy, secure returns. Be seen by over 70,000 monthly visitors. Visit us online to Buy / Sell / Trade / Consign Payment: Prompt payment is expected. Paypal is preferred but all forms of payment are accepted. Unpaid item case will be opened after 3 days if no payment received. Shipping Times: Most Domestic orders ship within 1 business day of purchase. For International orders or freight shipments, please allow 2-3 business days. In all cases, tracking information will be emailed to you at the moment the shipping label is created. If you cant find it or have other questions about shipping & logistics, please contact us. Shipping Costs: Flat rate shipping costs are applicable within the contiguous 48 States (USA). These rates are clearly posted on each product page. For an International or custom quote (including Hawaii, PR, AK) please contact us. Returns: Every purchase made on eBay carries a 30-day, satisfaction-guaranteed return policy. If youre not happy with your purchase for any reason or if youve simply changed your mind... no problem. Simply ship it back for a full refund or exchange (minus S&H costs). If you have received an item that is defective in some way, we will make it right. Let us know - we will pay for return shipping and repair the item or refund 100% of your original purchase price.

Hello. Cleaning up again. Here is for sale today is one excellent compact class A/AB integrated amplifier by Emotiva, model BasX 2m (mini). It could be used as an integrated amplifier with one Stereo RCA input and the switch in variable position, volume control adjusted via front knob. It is NOT designed to be operated via remote. You can also use it as a Headphone amplifier- the output and Volume are in the front. You can also use it as a power amp with all the connections and controls via your own favorite preamp. It will make a great desktop amplifier or you can use to drive a pair of bookshelf speakers, but it might not be suitable for large floorstanding speakers. I am the second owner, bought it for my secondary system which is still under construction while I am going thru a bunch of gear, and probably will be listing a bunch of gear in the future. I am the second owner, and as such do not have original box/package, but will pack safely for shipping. Unit is in excellent lightly used condition, extra clean. Works properly. See the specs below. Unit is for universal voltage. As with all used electronics, sold AS IS but guaranteed not DOA. Power Output: (Two Channels Driven) 50 watts RMS per channel; 20 Hz – 20 kHz; THD < 0.1%; into 8 Ohms. 90 watts RMS per channel; 1 kHz; THD < 1%; into 4 Ohms. • Power Output (headphone output; normal mode): 8 Ohms: 60 mW / channel; 33 Ohms: 200 mW / channel 47 Ohms: 250 mW / channel 150 Ohms: 430 mW / channel 300 Ohms: 440 mW / channel 600 Ohms: 350 mW / channel • Power Bandwidth (at rated power; 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.07 dB) • Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dB • THD + noise: < 0.02% (A-weighted); ref rated power. • Signal to Noise Ratio (8 Ohm load): > 112 dB; ref rated power; (A-weighted) • Minimum Recommended Load Impedance (per channel): 4 Ohms (equals one 4 Ohm load or two paralleled 8 Ohm loads) • Damping Factor (8 Ohm load): > 500 • Input Sensitivity and Gain (for rated power; 8 Ohm load): Fixed gain mode: 0.7 V / 29 dB. Variable gain mode: 0.5 V / up to 32 dB. • Input Impedance: 27 kOhms

Audio SpecificationsPower Output: (Two Channels Driven) • 50 watts RMS per channel; 20 Hz – 20 kHz; THD < 0.1%; into 8 Ohms• 90 watts RMS per channel; 1 kHz; THD < 1%; into 4 OhmsPower Output (headphone output; normal mode):• 8 Ohms: 60 mW / channel• 33 Ohms: 200 mW / channel• 47 Ohms: 250 mW / channel• 150 Ohms: 430 mW / channel• 300 Ohms: 440 mW / channel• 600 Ohms: 350 mW / channelPower Output (headphone output; direct drive mode - requires internal jumper; USE WITH CAUTION):• 8 Ohms: 50 watts / channel• 33 Ohms: 12 watts / channel• 47 Ohms: 8.5 watts / channel• 150 Ohms: 2.6 watts / channel• 300 Ohms: 1.3 watts / channel• 600 Ohms: 0.6 watts / channelPower Bandwidth (at rated power; 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.07 dB)Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dBTHD + noise: < 0.02% (A-weighted); ref rated powerSignal to Noise Ratio (8 Ohm load): > 112 dB; ref rated power; (A-weighted)Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads)Damping Factor (8 Ohm load): > 500Input Sensitivity and Gain (for rated power; 8 Ohm load): • Fixed gain mode: 0.7 V / 29 dB • Variable gain mode: 0.5 V / up to 32 dBInput Impedance: 27 kOhmsInput and Output Connections• Input Connections: Unbalanced (RCA); one each per channel• Speaker Output Connections: Audiophile grade 5-way binding posts• Headphone output (front panel): Full sized ¼” stereo headphone jackTrigger: • Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required• Trigger Output: 12 VDC; can drive any load up to 120 mAPower Requirements115 - 230 VAC @ 50 / 60 Hz (automatically detected)Front Panel Controls and Indicators• Standby: push button• Status LEDs: one per channel; blue• Status LEDs change to red to indicate a fault condition• Standby LED: amberRear Panel Controls• AC Power switch: slide switch selects between On and Auto-On modes• Gain switch: slide switch selects between Variable Gain and Fixed Gain modes

Brand new Class A/B amp, opened and tested. Was supposed to be used in my buddys retro system, but instead he had a vintage integrated fully updated. Can be used as a quality headphone amp. This amp is a great option for those wanting classic AB sound with the reliability of a new amp. Sound Quality First Designed first and foremost to sound great in all types of audio systems with all types of music. Great sounding Class A/B output stage ensures smooth, detailed sound and incredibly natural imaging, without a trace of harshness or strain. Low noise, wide bandwidth design, and a highly optimized input stage, lets you hear everything your high definition sources have to offer. Totally stable with real world speakers in real systems; not just on a test bench. The BasX A2m is a flexible stereo amplifier that combines excellent audio performance with several unique and extremely useful features. The A2m can be used as the foundation of a great small stereo system with or without a separate preamp. Its small size makes it the ideal solution for situations where space is limited or where multiple two-channel amplifiers will be used to power multiple different zones or sets of surround or height speakers. The A2m also features unique headphone output circuitry which is able to deliver great sound quality from a wide variety of both normal and difficult to drive headphones. The BasX A2m is a two channel power amplifier that delivers 50 watts / channel into 8 Ohms, and 90 watts / channel into 4 Ohms, with a rated THD+N of < 0.1%, and an A-weighted S/N ratio of 112 dB. The BasX A2m features the same high-quality Class A/B amplification and full-sized five way speaker binding posts as our other BasX power amplifiers, but utilizes an advanced switch mode power supply, which contributes to its compact form factor and efficient power utilization. The A2m has several additional features that make it uniquely flexible. A rear-panel switch allows the A2m to be used either as a power amplifier, with a fixed gain, or as an integrated amplifier, with higher gain, and a convenient front panel Volume control. This allows the A2m to be used with a single line level stereo analog source without the need for a separate preamp. Another switch allows the A2m to be configured to turn on automatically when it detects either a standard Trigger input, or an incoming audio signal. The front panel of the A2m includes a full-sized headphone jack driven by some very special headphone circuitry. Like the headphone outputs on highly-prized vintage gear, the headphone output on the A2m is powered directly from the main output amplifiers, through a pair of precision dropping resistors. This enables the A2m to power both regular low impedance headphones and demanding high impedance headphones with ease; a special internal jumper option allows you to route the main output power directly to the headphone output in order to drive low impedance planar headphones. Audio Specifications Power Output: (Two Channels Driven) 50 watts RMS per channel; 20 Hz 20 kHz; THD < 0.1%; into 8 Ohms 90 watts RMS per channel; 1 kHz; THD < 1%; into 4 Ohms Power Output (headphone output; normal mode): 8 Ohms: 60 mW / channel 33 Ohms: 200 mW / channel 47 Ohms: 250 mW / channel 150 Ohms: 430 mW / channel 300 Ohms: 440 mW / channel 600 Ohms: 350 mW / channel Power Output (headphone output; direct drive mode -requires internal jumper; USE WITH CAUTION): 8 Ohms: 50 watts / channel 33 Ohms: 12 watts / channel 47 Ohms: 8.5 watts / channel 150 Ohms: 2.6 watts / channel 300 Ohms: 1.3 watts / channel 600 Ohms: 0.6 watts / channel Power Bandwidth (at rated power; 8 Ohm load): 20 Hz to 20 kHz (+ / 0.07 dB) Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dB THD + noise: < 0.02% (A-weighted); ref rated power Signal to Noise Ratio (8 Ohm load): > 112 dB; ref rated power; (A-weighted) Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads) Damping Factor (8 Ohm load): > 500 Input Sensitivity and Gain (for rated power; 8 Ohm load): Fixed gain mode: 0.7 V / 29 dB Variable gain mode: 0.5 V / up to 32 dB Input Impedance: 27 kOhms Input and Output Connections Input Connections: Unbalanced (RCA); one each per channel Speaker Output Connections: Audiophile grade 5-way binding posts Headphone output (front panel): Full sized stereo headphone jack Trigger: Trigger Input: 5 12 V (AC or DC); <10 mA input current required Trigger Output: 12 VDC; can drive any load up to 120 mA Power Requirements 115 - 230 VAC @ 50 / 60 Hz (automatically detected) Front Panel Controls and Indicators Standby: push button Status LEDs:one per channel; blue Status LEDs change to red to indicate a fault Standby LED:amber Rear Panel Controls AC Power switch: slide switch selects between On and Auto-On modes Gain switch: slide switch selects between Variable Gain and Fixed Gain modes Internal Settings One pair of internal jumpers can be used to bypass the series dropping resistors to enable full output power to be routed directly to the headphone output (shipped with jumpers OFF) Protection The BasX A2m is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. Mechanical Dimensions:8-1/4 wide x 3 high x 14-1/4 deep (not including connectors) Weight: 7.5 lbs (unboxed) 10.5 (boxed)

I luv this amplifier. Only have had it for a short time. It is flawless. I purchased a new Luxman so I wont be needing this great integrated amp. It will put out 280wpc in 4ohm. Read the reviews. It truly sounds great. It is flawless not a single mark or scratch. Like you just took it out of the box.

Like new condition 50watts per channel and also a headphone amp. Can also be used as an integrated amp with volume control or bypassed as a std 2ch amp.

I am also selling a Parasound Halo P5 preamp which is a very nice pairing with the Emotiva. Specialprice for the combo. Do not hesitate to reach me out for any questions. Thanks,

This amp is in mint condition and has a nice stepped volume potentiometer with a metal knob Sold out now at Emotivas site 50w per channel at 8ohms 90w per channel at 4ohms Comes with all cables and a cover I ONLY SHIP LOWER 48 CONUS

This amp is in mint condition and has a nice stepped volume potentiometer with a metal knob Sold out now at Emotivas site 50w per channel at 8ohms 90w per channel at 4ohms Comes with all cables and a cover I ONLY SHIP LOWER 48 CONUS

This Emotiva Basx A2m power amplifier is in excellent working condition and ready for use. The Amplifier was purchased directly from EMOTIVA in Nov 2023 with 3 years warranty. This amplifier was used for 2 months and comes with the original manual, jumper, trigger cable, and power cord. Purchase with confidence knowing that youre getting a high-quality power amplifier from a trusted brand.Currently sold out everywhere.For more details. Please see emotiva website.https://emotiva.com/collections/basx-series/products/basx-a2m-stereo-flex-amplifierShipping to USA only.

Used but in excellent condition. This unit was in a seldom used secondary living room. A cool feature of this amp is the auto sensing feature that turns the amp on when it senses audio from a TV or Alexa/Google device. Introducing the Emotiva Basx A2mini power amplifier! This powerful device delivers exceptional performance and is perfect for audiophiles who crave high-quality sound. With its sleek design and impressive capabilities, the Emotiva Basx A2mini is the ideal addition to any home audio system. Featuring Emotivas signature sound quality, this amplifier is specifically designed to enhance your listening experience. With a compact size and multiple input options, its perfect for smaller spaces and versatile enough to work with a variety of audio sources. Whether youre enjoying your favorite tunes or settling in for a movie night, the Emotiva Basx A2mini is sure to impress.

Biete hier folgendes an: Fernbedienung für Emotiva XDA-2 Es handelt sich hier nur um die Fernbedienung, nicht um das Gerät selbst.Sie stammt aus einem tierfreien Nichtraucherhaushalt. Versendet wird als versichertes DHL-Paket mit Sendungsverfolgung. Viel Spaß damit...

The worlds largest online retailer of pre-owned audio Product DescriptionWho we areWhat we doOur ProcessOur Policies Emotiva BasX A2 Stereo Power Amplifier Product SKU: 53221 Voltage: 115V - 220V # of Owners: 1 Service History: None Serial Number: 3622114V010024 Age: 1 year Tobacco Exposure: No MSRP: $499 Cosmetic Description: Excellent condition with no notable blemishes.  What is Included: Amplifier, 3.5mm cable, Manual, Power cable, Factory packaging Other Notes: The BasX A2 the ideal amplifier to serve as the foundation of a great sounding stereo system, to power the front main speakers on a surround sound system, or to upgrade the front left and right channels of your favorite surround sound receiver. -Emotiva Functional Notes: Operational condition of this item is excellent, fully tested and no issues found. Shipping: Cost to ship this item within the contiguous United States is a flat rate of $55- including packaging and insurance. For all other locations including Hawaii, Puerto Rico and Alaska, please request a quote prior to purchase. Items with factory packaging will be double boxed. When factory packaging not available re-usable shipping box with custom injected-foam mold will be used. (for all items over 10 lbs). Note that all items valued over $750 will require a signature upon delivery. Your online source for the best value in new and used audio gear. Visit us online to Buy / Sell / Trade / Consign The Music Room is the largest online retailer of pre-owned HiFi equipment in the world. Headquartered in beautiful Boulder Colorado, The Music Room is a team of 17 strong (and growing) music lovers - all dedicated to one singular mission: delivering the very best online shopping experience in the audio industry - period. We specialize in well-cared for, previously used gear because that is what we are passionate about. We feel that there is nothing more fulfilling than creating a high-performance system on a budget with carefully selected used components, speakers and cables. Our program is safe, secure, fast, fair, hassle-free and highly effective. Visit us online to Buy / Sell / Trade / Consign Buy: Are you looking to get a fair price for your used home audio equipment without all the hassles, headaches, risks and fees? We will appraise your equipment and make you a quick, easy, fair cash offer. Just fill out our “get a quote” form on our homepage to start the process. Sell: We sell in multiple online venues with many (but not all) of our products available in our eBay store. Everything is quality-assured and backed by our best-in-class, satisfaction-guaranteed return policy. Trade: Make your budget go further with a generous trade-in allowance. Let us know what you have available, and we’ll get you the best possible trade-in allowance. We can even assist with shipping & logistics from anywhere in the USA. Just fill out our “get a quote” form on our homepage to start the process. Consign: We offer a hassle-free way for individuals and businesses to liquidate used gear. We’ll handle every step of the process from shipping to appraisals, customer service, fulfillment, and returns: Industry-low rates with no hidden fees Leverage our world-class reputation and get exposure in multiple sales venues - putting your product in front of over 570k monthly shoppers. Our program is Safe, Secure, Fast, Fair, Hassle-Free and Highly Effective. With 100% feedback ratings in every venue in which we sell, you can rest assured that we’ve got your back. Visit us online to Buy / Sell / Trade / Consign Quality Assurance: We offer 15-20 new product listings for sale daily. Each product undergoes an extremely rigorous quality-assurance and listening session by one of our qualified technicians. We understand that buying used audio equipment can be rife with uncertainty and unexpected headaches. Our quality assurance program is informed by a knowledge-base built through delivering over 30,000 used audio products to satisfied customers. We promise to deliver your product in good working order - exactly as described 100% of the time. Support: We don’t just make promises. We stand behind them - your satisfaction is guaranteed. Our support team is ready to help you with any questions you might have before and after the sale. Value: In the never-ending pursuit of high performance, it’s important to stretch your limited budget as far as possible. Used equipment sells for a fraction of new prices, and with a partner like The Music Room you can upgrade any time you like and get most of your money back. There’s simply no better way to maximize a limited audio budget. Packaging: We’ve invested thousands of dollars and countless hours into mastering our state-of-the-art packaging process. Our custom foam-in-place packaging system allows us to safely package almost any item regardless of irregular shapes or sizes. Most importantly, this system provides our customers with a re-usable shipping box which increases the resale value of the product and provides a shipping method for easy, secure returns. Be seen by over 70,000 monthly visitors. Visit us online to Buy / Sell / Trade / Consign Payment: Prompt payment is expected. Paypal is preferred but all forms of payment are accepted. Unpaid item case will be opened after 3 days if no payment received. Shipping Times: Most Domestic orders ship within 1 business day of purchase. For International orders or freight shipments, please allow 2-3 business days. In all cases, tracking information will be emailed to you at the moment the shipping label is created. If you cant find it or have other questions about shipping & logistics, please contact us. Shipping Costs: Flat rate shipping costs are applicable within the contiguous 48 States (USA). These rates are clearly posted on each product page. For an International or custom quote (including Hawaii, PR, AK) please contact us. Returns: Every purchase made on eBay carries a 30-day, satisfaction-guaranteed return policy. If youre not happy with your purchase for any reason or if youve simply changed your mind... no problem. Simply ship it back for a full refund or exchange (minus S&H costs). If you have received an item that is defective in some way, we will make it right. Let us know - we will pay for return shipping and repair the item or refund 100% of your original purchase price.

Its time for me to part with my BaseX A2 amplifier purchased from Emotiva 2-23-2023 so it still has 2+ years or warranty on. It has little use on it. Local pickup is preferred from the San Jose, CA area. it comes with the original boxes, cables and manuals. I can ship it, if you pay for shipping. There is nothing wrong with it. I just needed a bigger amp for my needs. If you have questions please message me. Thanks. The specs on this amplifier are: udio SpecificationsPower Output: (Two Channels Driven) 160 watts RMS per channel; 20 Hz – 20 kHz; THD < 0.1%; into 8 Ohms. 250 watts RMS per channel; 1 kHz; THD < 1%; into 4 Ohms.Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.07 dB)Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dBTHD + noise: < 0.02% (A-weighted); ref rated powerSignal to Noise Ratio (8 Ohm load): > 112 dB; ref rated power; (A-weighted).Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads).Damping Factor (8 Ohm load): > 500.Input Sensitivity (for rated power; 8 Ohm load): 1.2 V.Gain: 29 dB.Input Impedance: 27 kOhms. Input And Output ConnectionsInput Connections: Unbalanced (RCA); one each per channel.Speaker Output Connections: Audiophile grade 5-way binding posts.Trigger: Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA. Power Requirements115 VAC or 230 VAC @ 50 / 60 Hz (automatically detected).

Introducing the Emotiva XDA2 differential reference DAC XLR preamplifier controller. This high-quality pre-amp boasts stereo L/R RCA and XLR audio inputs, along with 2 outputs, making it the perfect addition to any home audio setup. The sleek black design and top-of-the-line components make this Emotiva model a must-have for any audio enthusiast. With a number of features, including 24-bit resolution and a variety of inputs and outputs, the Emotiva XDA2 is sure to impress. Whether you're a seasoned audiophile or just starting out, this pre-amp will take your listening experience to the next level. Don't miss your chance to own this top-of-the-line Emotiva XDA2 preamplifier controller. This item was in a nonsmoking environment and was used by a 66 year old audio enthusiast. It is in working condition and comes with its original remote and the (removable) sides to be hanged in a rack.

This listing is for the bottom 2 amps in the pictures. The XPA-100 is listed separately You can get 2 lightly used amps for the price of 1 new amp. They go for $499 & $549 new Audio Specifications BasX 2 channel Power Output: (Two Channels Driven) 160 watts RMS per channel; 20 Hz 20 kHz; THD < 0.1%; into 8 Ohms. 250 watts RMS per channel; 1 kHz; THD < 1%; into 4 Ohms. Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / 0.07 dB) Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dB THD + noise: < 0.02% (A-weighted); ref rated power Signal to Noise Ratio (8 Ohm load): > 112 dB; ref rated power; (A-weighted). Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads). Damping Factor (8 Ohm load): > 500. Input Sensitivity (for rated power; 8 Ohm load): 1.2 V. Gain: 29 dB. Input Impedance: 27 kOhms. Input And Output Connections Input Connections: Unbalanced (RCA); one each per channel. Speaker Output Connections: Audiophile grade 5-way binding posts. Trigger: Trigger Input: 5 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA. Power Requirements 115 VAC or 230 VAC @ 50 / 60 Hz (automatically detected). Front Panel Controls and Indicators Standby: push button. Status LEDs: one per channel; blue. Status LEDs change to red to indicate a fault condition. Standby LED: amber. Rear Panel Controls AC Power switch: rocker switch (switches AC main power). Status LEDs switch: disables front panel Status LEDs. Auto On Source detectible auto on Protection The BasX A2 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. Mechanical Dimensions: 17 wide x 4 high x 15-1/2 deep (not including connectors). 21-1/2 wide x 8 high x 21 deep (boxed). Weight: 25.2 lbs (unboxed) 33 lbs (boxed) Audio Specifications BasX 4 channel Power Output (ALL channels driven): 100 watts RMS per channel; 20 Hz 20 kHz; THD < 0.1%; into 8 Ohms. 130 watts RMS per channel; 1 kHz; THD < 1%; into 4 Ohms. Power Output (two channels driven): 100 watts RMS per channel; into 8 Ohms. 175 watts RMS per channel; into 4 Ohms. Power Bandwidth (at rated power; 8 Ohm load): 20 Hz to 20 kHz (+ / 0.02 dB) Broad Band Frequency Response: 10 Hz to 80 kHz +0/-1.8 dB THD + noise: < 0.02% (A-weighted); ref rated power Signal to Noise Ratio (8 Ohm load): > 115 dB; ref rated power; (A-weighted). Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads). Damping Factor (8 Ohm load): > 500. Input Sensitivity (for rated power; 8 Ohm load): 1.2 V. Gain: 29 dB. Input Impedance: 27 kOhms. Input And Output Connections Input Connections: Unbalanced (RCA); one each per channel. Speaker Output Connections: Audiophile grade 5-way binding posts. Trigger: Trigger Input: 5 12 V (AC or DC); <10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 120 mA. Power Requirements 115 VAC or 230 VAC @ 50 / 60 Hz (automatically detected). Front Panel Controls and Indicators Standby: push button. Status LEDs: one per channel; blue. Status LEDs change to red to indicate a fault condition. Standby LED: amber. Rear Panel Controls AC Power switch: rocker switch (switches AC main power). Status LEDs switch: disables front panel Status LEDs. Protection The BasX A4 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. Mechanical Dimensions: 17 wide x 4 high x 15-1/2 deep (not including connectors). 21-1/2 wide x 8 high x 21 deep (boxed). Weight: 26 lbs (unboxed) 32 lbs (boxed)

Introducing the Emotiva BasX A2 power amplifier, a high-quality audio device that delivers exceptional sound performance. This amplifier features two channels and is designed to work with a variety of home audio systems. The sleek black color and brand name, Emotiva, add a touch of sophistication to your entertainment setup. This power amplifier is perfect for audiophiles who demand the best in sound quality. With its high-end components, your music and movies will come to life like never before. The Emotiva BasX A2 is a must-have for anyone who wants to experience audio in its purest form.

Introducing the Emotiva XDA2 differential reference DAC XLR preamplifier controller. This high-quality pre-amp boasts stereo L/R RCA and XLR audio inputs, along with 2 outputs, making it the perfect addition to any home audio setup. The sleek black design and top-of-the-line components make this Emotiva model a must-have for any audio enthusiast. With a number of features, including 24-bit resolution and a variety of inputs and outputs, the Emotiva XDA2 is sure to impress. Whether you're a seasoned audiophile or just starting out, this pre-amp will take your listening experience to the next level. Don't miss your chance to own this top-of-the-line Emotiva XDA2 preamplifier controller. This item was in a nonsmoking environment and was used by a 66 year old audio enthusiast. It is in working condition and comes with its original remote and the (removable) sides to be hanged in a rack.

Emotiva TA2 Integrated HiFi Amplifier. Used for a few months before I upgraded. Sounds great. In near new condition. Used in non-smoking pet free home. MSRP = $999.00. I will pay for shipping in the continental US using the original shipping box.

Emotiva XDA2 2 Differential Reference DAC XLR 24 Bit Preamplifier Controller. Introducing the Emotiva XDA2 differential reference DAC XLR preamplifier controller. This high-quality pre-amp boasts stereo L/R RCA and XLR audio inputs, along with 2 outputs, making it the perfect addition to any home audio setup. The sleek black design and top-of-the-line components make this Emotiva model a must-have for any audio enthusiast.With a number of features, including 24-bit resolution and a variety of inputs and outputs, the Emotiva XDA2 is sure to impress. Whether youre a seasoned audiophile or just starting out, this pre-amp will take your listening experience to the next level. Dont miss your chance to own this top-of-the-line Emotiva XDA2 preamplifier controller.