Description
Crestron by ATI CNAMPX-7X200 Watts 7-Channel Power Amplifier Used, Working Perfectly MADE IN USA Seven channel 200W 8Ohm 300W 4Ohm YOU NEED A 12-24 Volt DC POWER TRANSFORMER (0.5Amp or more) TRIGER TO TRIGER THE UNIT TO WORK You can get one on eBay for less than $5 I may have some to include on this sale The CNAMPX-7X200 provides 7 channels of world-class audio amplification as part of a complete Crestron Home® theater system. Brilliantly designed to complement Crestrons DAP8 7.1 surround sound processors, the CNAMPX-7X200 delivers a vigorous 200 watts per channel into 8 ohms, and 300 watts per channel into 4 ohms. Its massive twin toroidal power transformers feature MOH cores for maximum efficiency, with bifilar windings directing pure, continuous power to each of the seven mono amplifier channel modules. Each channel module includes its own power supply fed by a separate set of transformer windings, producing astounding dynamic range and very low distortion from every channel, all the time. The highest grade components mounted to multi-layer FR-4 glass epoxy circuit boards help guaranty a long life of trouble free operation. With more than 300 square inches of heat sink surface area per channel, cool, quiet, and reliable operation is ensured. Gentle power-up is achieved through a soft-start inrush current limiting circuit. Quick-response opto-coupled output protection on each channel prevents failures caused by speaker line faults or signal spikes, providing exceptional dependability with no compromise to sound quality. In the unlikely case of a failure, Crestrons Detachable Modular Component design allows for rapid repair in the field.Its interface to the Cresnet control network affords remote power control and monitoring of the internal temperature. Over-temperature conditions can be sensed by the control system and used to display a warning message on a touchpanel, reduce audio levels, or even activate an external cooling fan.Audio Typical of 7 Mono Channels: Output Power20Hz to 20kHz, all outputs driven at rated THD:200 watts per channel at 8 ohms300 watts per channel at 4 ohms Power Bandwidth3Hz to 150kHz, +0/-3dB Frequency Response20Hz to 20kHz, +0/-0.1dB at 1 watt, 8 ohms Total Harmonic Distortion (THD)?0.03% at full power SMPTE I.M. Distortion?0.05% S/N Ratio>110dB A-weighted Gain28dB Damping Factor>400 Channel Separation>100dB, 20Hz to 20kHzConnectors INPUTS 1 – 7 (7) RCA female;Unbalanced line-level audio inputs;Input Impedance: 28k ohms;Connect to 7.1 outputs of C2N-DAP8 or C2N-DAP8RC OUTPUTS 1 – 7(7) Dual 5-way binding posts;Speaker-level audio outputs;Output Power: 200 Watts/Ch. @ 8 ohms, 300 Watts/Ch. @ 4 ohms;Connect to 7.1 speaker system (excluding subwoofer) G6-32 screw, chassis ground lug NET(1) 4-pin 3.5mm detachable terminal block;Cresnet slave port, connects to Cresnet control network 120V~60Hz(1) 20 Amp IEC male;Mates with removable power cord (included)Controls & LED Indicators POWER (front)(1) Toggle switch with (1) green LED, enables/disables main power if Cresnet power and mains power are connected PWR (rear)(1) green LED, indicates 24 Volts DC power supplied from Cresnet control network NET (rear)(1) yellow LED, indicates communication with Cresnet system OVERRIDE/SETUP (rear)(1) miniature pushbutton and (1) red LED, overrides control system to activate main power; Cresnet power and mains power must be connected; also used for touch-settable ID (TSID) MASTER SWITCH20 Amp magnetic circuit breaker for main power inputPower Requirements Main Power120 Volts AC ±10%, 60 Hz, 2400 Watts;Requires dedicated 20 Amp circuit Cresnet Power Usage3 Watts (0.125 Amps @ 24 Volts DC)Environmental Temperature41° to 104°F (5° to 40°C) Humidity10% to 90% RH (non-condensing)Enclosure Black metal, 4U 19-inch rack-mountable (rack ears included)Dimensions Height7.69 in (19.53 cm);7.0 in (17.78 cm) without feet Width17.18 in (43.64 cm);19.0 in (48.26 cm) with rack ears Depth19.07 in (48.44 cm)Weight 94.4 lbs (42.48 kg)INTERNATIONAL VERSION (230 VAC) CNAMPXI-7X200 All the features and specifications of the CNAMPX-7X200 except: Connectors (partial) OUTPUTS 1 – 7(7) Dual binding posts;(Banana plugs prohibited);Speaker-level audio outputs;Output Power: 200 Watts/Ch. @ 8 ohms, 300 Watts/Ch. @ 4 ohms;Connect to 7.1 speaker system (excluding subwoofer) 120V~50Hz(1) 20 Amp IEC male;Mates with removable power cord (included) Controls & LED Indicators (partial) MASTER SWITCH10 Amp magnetic circuit breaker for main power input Power Requirements Main Power120 Volts AC ±10%, 50 Hz, 2400 Watts Cresnet Power Usage 3 Watts (0.125 Amps @ 24 Volts DC) WE ARE LOCATED IN SIMI VALLY CALIFORNIA PLESE SEE PHOTOS FOR ALL THE DETAILS.PLESE CHECK MY STORE AND OTHR ITEMS ALL ITEMS ARE TESTED BEFORE LISTING AND BEFORE SHIPPING. All listings can be canceled without any noticedWe use some other sites for selling to local and international customers If item is used, it has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. CHECK MY FEEDBACK AND BUY WITH CONFIDENCE. POLICY:Buyers have 14 days after the delivery to return the item if return is accept in that sale.We ask all buyers to email us before opening a EBAY CLAIM CASEWe ask all the buyers before leaving a negative or neutral, please email us with the problem first and we will do our best to solve it for you.We care about our buyers and we only want to see them happy.WE WANT TO SEE ALL OUR BUYERS SATISFIEDALL INTERNATIONAL BUYER”ShippingShippings are via FedEx, UPS or USPS ground Shipping will start In same or two days depending on your item.Shipping rate is for USA continental ONLY and is rated to all 48 state, please do not ask for the lower shipping rate. Local pick and inspection is free and can be CASH NO TAX when you do pick up.Shipping address must match eBay profile and CAN NOT be changed ALASKA AND HAWAII BUYERS must ask for the shipping rate before purchase.
Live search