Connoisseur Bd2 Power Switch A. R. Sugden. Before it was taken apart it used to work, I cannot guarantee that It will work now. Selling as is Thank you for looking

*****Has now been set-up & tested with a 33 rpm & a 45 rpm record. Speeds are constant & accurate on both settings & the Pickup cartridge sounds really good when connected to an amp**** Vintage 1950s Sugden BD1 turntable kit with a Sugden SAU2 tonearm / headshell with a Shure M75ED-2 cartridge. The tonearm 5 point connect wire gives 2 x standard audio connectors output. . 1 spare headshell is also present, as is the original tonearm rest & A4 instruction/spec sheet on this SAU2 tonearm.The turntable has a brand new capsule of Farnells grease & a bottle of thick oil to set this turntable up. I have improved it by the addition of a brand new drive belt & have serviced the motor & made a new suspension harness from vulcanised India rubber, as was there originally rather than a modern nitrile rubber sheet web assembly, to keep to the spirit of things. A spare length of this India rubber is also included with the turntable / tonearm.the motor runs smoothly on both pulley wheel stages & the flip-up corner mounted drive cover is un-split on the hinged area. The black motor board paintwork is around 99%+ present & shows little signs of any scuffing. Not bad for over 75 years old. The motor / turntable also has ALL of its original paperwork including a full size template to fix to a wooden deck.The turntable is heavily cast in Aluminium & the turntable mat is flexible & neither cracked nor perished. Generally speaking a real sleeper, ready to be set up again by someone who would appreciate this well conceived audio classic do-it-yourself record player. Thanks for looking.

Platine vinyle rétro Sugden CONNOISSEUR BD2/A - vintage. Le lecteur de musique légendaire pour amateurs et collectionneurs sera un ajout élégant à votre intérieur et vous donnera le plaisir d'écouter des disques vinyles, vous plongeant dans l'atmosphère appropriée.  Se connecte aux haut-parleurs modernes (RCA Jack). Il y a un éclat sur le coin du couvercle (on peut le voir sur la photo), mais cela ne pose pas de problème et ne gâche pas la vue.

Sugden BD1 Connoisseur Turntable Sold For Parts Or Repair - Has Low Audible Earth Hum Owned From New (1971) And Very Well Looked After Motor Good - Recent New Drive Belt SAU 2 Tonearm With Shure M75 Cartridge & Original Elliptical Shure Stylus In Very Good Condition Standard Turntable In Very Good Condition As Seen In The Photos Lid Has Some Fine Lines And Marks But Polishes Up Well And Looks Good Will Come With Original Manual & Additional Weights Etc The Turntable Will Be Very Well Packed And You Will Receive It Exactly As Seen In The Photos Overall A Very Good Sugden BD1 Turntable For Repair Or Parts Please Be Sure Of What You Are Buying As This Item Is Sold As Seen With No Returns International Buyers Please Contact Us For An Accurate Shipping Quote

This was my main loving room turntable for over 10 years but I've recently switched to a Thorens TD 165 so letting it go. I replaced the motor suspension and drive belt a few years ago though it may be time to replace the latter again. Includes a nice vintage Shure M44MB cart and genuine Shure stylus with plenty of life left. There is a rack at the corner of the lid which can't really be seen if put at the back, otherwise all great condition. Includes phono connector for the SAU-2 tonearm (with ground lead).

This will require new webbing for the motor, a drive belt and a phono connector for the SAU-2 tonearm. I had kept this unit for spares but am now selli gmy BD2 (see other listing) sono lo ger need it. No dustcover.

Please study the picture. Parts are untested but I believe should be functional.

Connoisseur Bd2 Power Switch A. R. Sugden. Before it was taken apart it used to work, I cannot guarantee that It will now after being in a box for years. Selling as is for parts!! Thank you for looking

Full working order, tonearm with cable, headshell and armrest. Nothing else in photos included.

A R Sugdens Connoisseur BD.1 Turntable. Vintage turntable comes with working motor & belt but does not include tone arm or cartridge. The arm board fitted has been cut to receive tone arm and there is also a spare uncut arm board. Great example of a vintage deck, nice thin wooden surround. Do not have original packaging but will be packed securely. Smoke, pet & child free environment No returns & thanks for looking

Connoisseur Bd2 Power Switch A. R. Sugden. Before it was taken apart it used to work, I cannot guarantee that It will now after being in a box for years. Selling as is for parts!! Thank you for looking

Connoisseur Bd2 Power Switch A. R. Sugden. Before it was taken apart it used to work, I cannot guarantee that It will now after being in a box for years. Selling as is for parts!! Thank you for looking

Sugden Connoisseur Arm SAU2. Working but wants a piece gluing back on headshell (hence tie wrap) Looks ok, no phono cable but internal wiring is fine. Spares or repairs

Connoisseur Sugden SAU-2 Tonearm In Fair Condition. It’s a beautiful arm that I had wanted to install but I don’t have the time. Problems are: - no cable. 5 pin din cable required - the arm lift has had a small crack but it seems to have been glued back - the arm collar screw feels in tight and I can’t undo it. Someone else may have better luck From Vinylengine: The SAU2 is a bit like a classic car : you wouldnt expect it to out-perform todays models, but its great fun to use anyway! Starting at the sharp end, the plastic headshell simply isnt a good design. Its a slide-on friction-fit to the tonearm, and mine was quite loose, cured for now by wrapping a bit of scotch tape round the tonearm shaft but thats hardly a permanent solution. Within the body of the headshell theres a slide-out plug which takes the cartridge leads on pins at one end and plugs into the tonearm at the other. The space enclosing it is so constricted that normal cartridge leads are squashed together and short out. The plug looks eminently meltable so I ruled out soldering leads directly to the pins. I had to source some ultra-thin cartridge clips and make a piece of plastic shielding to fit between them. The slot-holes taking the cartridge mount bolts arent very long, hence not much room for adjustment, and I found it impossible to get a good alignment with some cartridges. At the other end, theres no counterweight calibration dial for the tracking force so it has to be set with a guage or digital scale. The distinctly odd 45-degree offset gimbal arrangement is commendably friction-free and seems to work OK : the trick to getting the headshell to stay horizontal while on the record is to point the outer gimbal at the centre of the playing surface where the needle sets down, and then set the tonearm height so as to be exactly horizontal in the playing position. It does look distinctly strange to see it tilt when you lift it off, though. The anti-skate seems to function as it should, its never an exact science anyway. The base of the tonearm shaft takes a 5-pin male plug which isnt easy to find. I eventually got a suitable Cardas model from e-bay and made up a tonearm lead. Get an SAU2 with a lead if you can! Despite its odd features the SAU2 actually works quite well. I put it through some basic tracks on test records and whilst it didnt excel, it didnt disgrace itself either. Probably a near-match for the Pioneer PL12D tonearm as a reference point. For the music I listen to on a day-to-day basis (fairly mainstream pop/rock/blues/prog/folk from the 60s and 70s) its absolutely fine : I suspect its limitations would become apparent with more demanding classical orchestral music and such-like. It has some character and a nice 50s/60s vintage vibe about it, and Im enjoying using it with an AT91 on a Connoisseur BD1 turntable.

Connoisseur Bd2 Power Switch A. R. Sugden. Before it was taken apart it used to work, I cannot guarantee that It will now after being in a box for years. Selling as is for parts!! Thank you for looking

Purchased in the 1970s Switches on ok and turntable spins but is very noisy. 2 speed, 33 & 45 rpm. Shure M75 type 2 cartridge & stylus included (stylus is separate and the protective sponge is disintegrating). SAU 2 pick up arm. Groov-Kleen cleaner. Stylus pressure gadget. The plinth cover is in good condition. Needs a 3 pin plug I would prefer collection from CM11 postcode. Will post but please bear in mind I do not have the transport screws. Any questions, please ask.

Connoisseur Bd2 Power Switch A. R. Sugden. Before it was taken apart it used to work, I cannot guarantee that It will now after being in a box for years. Selling as is for parts!! Thank you for looking

Connoisseur Sugden SAU-2 Tonearm In Fair Condition. It’s a beautiful arm that I had wanted to install but I don’t have the time. Problems are: - no cable. 5 pin din cable required - the arm lift has had a small crack but it seems to have been glued back - the arm collar screw feels in tight and I can’t undo it. Someone else may have better luck From Vinylengine: The SAU2 is a bit like a classic car : you wouldnt expect it to out-perform todays models, but its great fun to use anyway! Starting at the sharp end, the plastic headshell simply isnt a good design. Its a slide-on friction-fit to the tonearm, and mine was quite loose, cured for now by wrapping a bit of scotch tape round the tonearm shaft but thats hardly a permanent solution. Within the body of the headshell theres a slide-out plug which takes the cartridge leads on pins at one end and plugs into the tonearm at the other. The space enclosing it is so constricted that normal cartridge leads are squashed together and short out. The plug looks eminently meltable so I ruled out soldering leads directly to the pins. I had to source some ultra-thin cartridge clips and make a piece of plastic shielding to fit between them. The slot-holes taking the cartridge mount bolts arent very long, hence not much room for adjustment, and I found it impossible to get a good alignment with some cartridges. At the other end, theres no counterweight calibration dial for the tracking force so it has to be set with a guage or digital scale. The distinctly odd 45-degree offset gimbal arrangement is commendably friction-free and seems to work OK : the trick to getting the headshell to stay horizontal while on the record is to point the outer gimbal at the centre of the playing surface where the needle sets down, and then set the tonearm height so as to be exactly horizontal in the playing position. It does look distinctly strange to see it tilt when you lift it off, though. The anti-skate seems to function as it should, its never an exact science anyway. The base of the tonearm shaft takes a 5-pin male plug which isnt easy to find. I eventually got a suitable Cardas model from e-bay and made up a tonearm lead. Get an SAU2 with a lead if you can! Despite its odd features the SAU2 actually works quite well. I put it through some basic tracks on test records and whilst it didnt excel, it didnt disgrace itself either. Probably a near-match for the Pioneer PL12D tonearm as a reference point. For the music I listen to on a day-to-day basis (fairly mainstream pop/rock/blues/prog/folk from the 60s and 70s) its absolutely fine : I suspect its limitations would become apparent with more demanding classical orchestral music and such-like. It has some character and a nice 50s/60s vintage vibe about it, and Im enjoying using it with an AT91 on a Connoisseur BD1 turntable.

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

Vintage A R Sugden Connoisseur turntable on Texan pre amp deck. Untested as I havent got the specific circular mains plug that fits into the back. Please study the detailed pictures as they form a larger part of the description and overall condition. Also has the stylus balance and record cleaner. Postage cost due to size and weight. Collection preferred where possible from London SE9 3JL. Thanks.

Thorens td 150 turntable MkII with Sugden Connoisseur Pickup Arm type SAU 2.In pretty good condition considering age. A few marks and scratches on the wood (see photos). We have the original box, although cant find the original instructions for the turntable but do have them for the arm.Collection only, from London (or Brighton if more convenient)

Connoisseur Sugden SAU-2 Tonearm In Fair Condition. It’s a beautiful arm that I had wanted to install but I don’t have the time. Problems are: - no cable. 5 pin din cable required - the arm lift has had a small crack but it seems to have been glued back - the arm collar screw feels in tight and I can’t undo it. Someone else may have better luck From Vinylengine: The SAU2 is a bit like a classic car : you wouldnt expect it to out-perform todays models, but its great fun to use anyway! Starting at the sharp end, the plastic headshell simply isnt a good design. Its a slide-on friction-fit to the tonearm, and mine was quite loose, cured for now by wrapping a bit of scotch tape round the tonearm shaft but thats hardly a permanent solution. Within the body of the headshell theres a slide-out plug which takes the cartridge leads on pins at one end and plugs into the tonearm at the other. The space enclosing it is so constricted that normal cartridge leads are squashed together and short out. The plug looks eminently meltable so I ruled out soldering leads directly to the pins. I had to source some ultra-thin cartridge clips and make a piece of plastic shielding to fit between them. The slot-holes taking the cartridge mount bolts arent very long, hence not much room for adjustment, and I found it impossible to get a good alignment with some cartridges. At the other end, theres no counterweight calibration dial for the tracking force so it has to be set with a guage or digital scale. The distinctly odd 45-degree offset gimbal arrangement is commendably friction-free and seems to work OK : the trick to getting the headshell to stay horizontal while on the record is to point the outer gimbal at the centre of the playing surface where the needle sets down, and then set the tonearm height so as to be exactly horizontal in the playing position. It does look distinctly strange to see it tilt when you lift it off, though. The anti-skate seems to function as it should, its never an exact science anyway. The base of the tonearm shaft takes a 5-pin male plug which isnt easy to find. I eventually got a suitable Cardas model from e-bay and made up a tonearm lead. Get an SAU2 with a lead if you can! Despite its odd features the SAU2 actually works quite well. I put it through some basic tracks on test records and whilst it didnt excel, it didnt disgrace itself either. Probably a near-match for the Pioneer PL12D tonearm as a reference point. For the music I listen to on a day-to-day basis (fairly mainstream pop/rock/blues/prog/folk from the 60s and 70s) its absolutely fine : I suspect its limitations would become apparent with more demanding classical orchestral music and such-like. It has some character and a nice 50s/60s vintage vibe about it, and Im enjoying using it with an AT91 on a Connoisseur BD1 turntable.

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

A R Sugden Connoisseur BD1 Turntable -Spares /Repairs. Not sure about the history with this one Was in amongst a job lot of turntables I purchased Has nice oak plinth in good condition , the platter seems to be missing the rubber mat , switch is missing the main on /off lever , motor and internal circuits all present no idea of the condition Great little project if anyone has the time !