Apart Audio Biamp Champ One Leistungsverstärker Power Amplifier PA & Gewährleistung - Demogeräte ohne OVP- 1 Jahr Gewährleistung- geprüfte Ware- technisch neuwertig- leichte Gebrauchsspuren, siehe Fotos- Rechnung mit ausgewiesener MwSt Apart Audio Champ 1 One Product DetailsChamp-One realizes what many in the audio industry deemed impossible: an amplifier without cooling fans that is capable of delivering high-end musical sound, high dynamics, high reliability.Unique heat sinksEspecially for Champ-One APart introduces the unique, custom-designed side mount heat sinks. In combination with a self-supporting low resonance frame, they make it possible to create a discrete high power amplifier without a noisy and dust-collecting fan inside the enclosure.This means: less maintenance, no annual fan or dust filter exchange procedure, no more amplifier cleanout, and no more unwanted noise from cooling fans. Champ-One relies on convection cooling only, a unique feature in its output power class!APC power management circuitry gets the best out of an amplifierAPC power management circuitry has been designed especially for Champ-One. It is one of the most intelligent amplifier protection circuits ever designed, simply because it does the job without interfering with the typical dynamic character of music.APC allows the user to preset the power potential of the amplifier, while maintaining high power reserves and thus producing high, clean power. It constantly analyses incoming music signals and keeps dynamics alive. An additional ultra fast peak limiter avoids amplifier clipping. With APC, your system is always in control, including your speakers.All the components in Champ-One are audiophile grade quality. Thanks to the tube emulation circuitry, the unit produces an exceptionally warm sound, which considerably reduces listeners fatigue.The striking design and technical innovations of the Champ-One are setting new industry standards....whether it is for AV, studio, gigs, home or catering applications: experience the pure musical power of Champ-One!Features:Fanless 2 x 600W Power Amplifierhigh efficiency > 70%APC power managementSound selection: Solid or TubeExtensive Protection CircuitBridge- or Stereo ModeUser protected power and sound settingsColor: blackDynamic program power: Bridge-mono (8 ohm) 1100 W, 2 channel (4 ohm) 2 x 600 WInput impedance: 10 kOhm (RCA), 20 kOhm (XLR)Frequency response: 10 Hz - 50 kHz, (0, -0.5 dB)Distrotion: < 0.05 %Signal to Noise Ratio: > 100 dBAGain: 33 dB (39 dB bridged)Protection circuits: DC, HF, clip, overcurrent, short-circuit, 2 step Temperature protectionCooling: convectional, no fanPower consumption: 18VA idle, 1KVA full program, 1.5KVA peakMains power requirements: 230VAC, 50HzDimensions (W x H x D): 48.3 x 8.8 x 38 cmWeight: 13 kg

Verkaufe einen professionellen Verstärker von APart, der einwandfei funktioniert. Für weitere Informationen gerne auf der Website nachgucken: https://www.musikhaus-korn.de/de/apart-audio-champ-4/pd/38030 . Gerne vorbeikommen, um sich ein Bild zu machen. Abholung bevorzugt. Bei Fragen gerne schreiben. Features: Lüfterloser 4x 125W Leistungsverstärker APC Leistungsregulierung Umfangreiche Schutzschaltung Brücken-, Stereo- und Dual-Mono Betrieb Schaltbarer Hoch- und Tiefpassfilter für Subwoofer/Satellitenlautsprecher Nur 1 HE Technische Daten: Leistung (Musik): Brückenbetrieb (8 Ohm) 230 W, 4-Kanal (4 Ohm) 4 x 125 W Eingangsimpedanz: 10 kOhm Frequenzgang: 20 Hz - 40 kHz, (0, -0,5 dB) Verzerrung: < 0,1 % Rauschabstand: > 100 dBA Verstärkung: 26 dB (32 dB gebrückt) Schutzschaltung: DC, HF, Übersteuerung, Kurzschluss, 2-stufige Temperatursicherung Kühlung: Konvektionskühlung, kein Lüfter Filter (Kanal 1/2): Tiefpassfilter 100Hz/12dB/oct, APart spezifisch - schaltbar Filter (Kanal 3/4): Hochpassfilter 100Hz/12dB/oct - schaltbar Leistungsaufnahme: 26VA Leerlauf, 400VA Vollast Spannungsversorgung: 230 VAC, 50Hz Abmessungen (B x H x T): 48,3 x 4,4 x 36 cm Gewicht: 7,5 kg

Amplifier Bi-Color, AP art Champ One Hochwertig, voll funktionstüchtig Hervorragende Klangqualität 2 x 600W Power Amplifier Gesamtgewicht 13kg Maße: 48.3 x 8.8 x 38 cm (b x h x t) NUR Abholung!

Amplificatore Hi-end Apart Champ One. A chi interessato sono disposto a fare le foto del prodotto e delle sue condizioni, essendo molto pesante. Caratteristiche: Fanless 2 x 600W Power Amplifier high efficiency > 70% APC power management Sound selection: Solid or Tube Extensive Protection Circuit Bridge- or Stereo Mode User protected power and sound settings Color: black Dynamic program power: Bridge-mono (8 ohm) 1100 W, 2 channel (4 ohm) 2 x 600 W Input impedance: 10 kOhm (RCA), 20 kOhm (XLR) Frequency response: 10 Hz - 50 kHz, (0, -0.5 dB) Distrotion: < 0.05 % Signal to Noise Ratio: > 100 dBA Gain: 33 dB (39 dB bridged) Protection circuits: DC, HF, clip, overcurrent, short-circuit, 2 step Temperature protection Cooling: convectional, no fan Power consumption: 18VA idle, 1KVA full program, 1.5KVA peak Mains power requirements: 230VAC, 50Hz Dimensions (W x H x D): 48.3 x 8.8 x 38 cm Weight: 13 kg

APart Champ One Stereo Power Amplifier. Full working order and excellent condition. SpecificationsPower output: 300 watts per channel into 8? (stereo), 900 watts into 8? (mono)Frequency response: 10Hz to 50kHzTotal harmonic distortion: 0.05%Damping factor: 100Gain: 33 dBInput sensitivity: 1VSignal to noise ratio: 100dBSpeaker load impedance: 4? (minimum)Dimensions: 483 x 88 x 380mmWeight: 13kgTERMS & CONDITIONSIMPORTANT - PLEASE READ BEFORE PURCHASING 1. Returns 1.1 All items are sold with either a 14 or 30 day return policy as stated in the listing. Please contact us as soon as possible in the unlikely event that your item arrives not as described and we will be sure to resolve the issue. Abuse of the return policy is in breach of eBays T&Cs. Products may be invisibly security marked. All unscrupulous buyers will be reported and an action fraud case will be opened. 1.2 If goods are returned as surplus to your requirement and are not faulty on receipt, a restocking charge of 20% will apply. 2. Power Cables 2.1 In order to reduce electronic waste, unless stated, units that require standard IEC kettle or figure of eight power cables will not be included unless requested. If you require one, please let us know immediately after purchasing and we will include one free of charge. 3. International / Non Mainland UK Buyers 3.1 Most of our items are available to purchase via eBays global shipping program. If postage costs are not displayed to you, please contact us before pressing buy it now and we will try to find a solution. 4. General/Other 4.1 All of our shipments are carefully packaged to ensure safe carriage. All fragile packages are clearly marked as fragile and we do our utmost to ensure that they arrive to you intact. Recycled packaging materials will be made use of where appropriate. Thank you for looking, happy eBaying!

  TUBE HUNTER VACUUM TUBE GEMS THESE ARE THE SPECIFICS OF THE TUBE/TUBES/PARTS FOR SALE THESE ARE THE TUBE/TUBES/PARTS FOR SALE:  MANUFACTURER:                              SYLVANIA PRODUCTION CITY:                                    USA TUBE TYPE:   5Y3 GT DESIGNATION:                                             AWESOME US RECTIFIER FENDER  ORIGINAL YEAR:   1958 MONTH:   WEEK 13 Date code match   SINGLE SILK SCREEN CONDITION %:                    100% MICA:   1 PLATES:   BLACK GM%:   120%, 119% SINGLE/PAIR/QUAD/MULTI:   SINGLE GETTER:                                                          TOP D  GETTER DATE CODE                                                    58-13   Normal 0 false false false EN-US X-NONE X-NONE Fender lost its juice? Rectify that situation with this awesome replacement. On my tester a B&K 747 tester:    Below 55 = BAD      55-65 = ?     65 -100 = Good     100-120+ = NOS     I want to see you happy with your purchase. I will never sell a tube that is below standard…… I have sold many tubes here on Ebay, and all my customers have been completely satisfied. I will work with you in good faith if there are any problems, or if you are unsatisfied in any way. I want your business now and in the future, so I assume you are the boss, and I am the employee. All tubes are tested for shorts, continuity, and emissions. I prefer PayPal. ALL CUSTOMERS PLEASE READ ALL NOTES BEFORE BUYING FROM ME !!1.  RETURNS: It is my highest desire that you are completely satisfied with your purchase from me. I will bend over backwards to make sure that you are a happy customer.If anything you buy from me is less than satisfactory, message me BEFORE you either open a case or hit the “item not as described” button.Sound quality is tremendously SUBJECTIVE. For tubes returned for noise or sound quality of any kind you pay for the shipping we refund the purchase. We refund the price of the item NOT THE SHIPPING COST. If we sent the wrong tube we will of course pay for return shipping. For any tubes that are DOA we require that you send a us a picture of the shipping box to show us the damage. We test EVERY tube sent out and none should be DOA unless broken in shipping.2.    PLEASE NOTE:  Tube silkscreen (lettering on the tubes) is VERY fragile. It can be wiped off and destroyed VERY easily. If you wipe off the silkscreen while handling the tube you diminish their value by up to 70%. DO NOT handle the tubes or hold them from the cylinder. ALWAYS hold them from the ENDS. If you are returning tubes and they are not in the same condition cosmetically I cannot give you a full refund. THIS IS VERY IMPORTANT.3.  UNLESS YOU MAKE ARRANGEMENTS WITH US BEFORE YOU PURCHASE, YOU MUST PAY FOR ITEMS PURCHASED WITHIN 2 DAYS OR A CASE WILL BE OPENED FOR AN UNPAID ITEM!!!4. TESTING: I test all tubes that I sell in one way or another, or I will state untested. I have a B&K 747 tube tester. This is a mutual conductance tester. It give a percentage value of gm for the tube under test and checks for shorts and grid emissions. I also use a Tektronix curve tracer for testing triodes. I give a number of evaluations for tubes. One evaluation is a screen shot of the tube with a high voltage applied to the plate. This helps the buyer see the linearity of the tube in question at the highest voltage the tube will see in a real circuit. The Curve tracer steps the triode through 10 gate/grid voltages starting with -10 volts and going to 0 volts. The lines show how the tube conducts throughout that range. At 0 volt the tube is at max conduction and is the top line on the display. It is easy at that point to take where that top line intersects the plate voltage, find the milliamp level and compare it to the datasheet. I give those numbers for you in the Item condition box. To further help the buyer I also include the Design values, for gm and ma readings in the table. This can then be compared to other tube sellers using inferior test methods such as Hickok,  Amplitrex, and other testers. The Tektronix curve tracer gives values within 3% of the actual value. The very best portable testers only can approach 10% accuracy.5.    Please note: The numbers given for gm are what I see on my tester. I DO NOT guarantee that you will see those numbers on your tester. I only guarantee that these tubes will test good, with no shorts, or gas, on a decent calibrated tester. I dont guarantee or imply anything else.6. VERY IMPORTANT!!! Vintage tube testers almost always, due to age, have VERY LOW HEATER VOLTAGES!!!  Every tester I have ever bought is below 6 volts when selecting 6.3 volts. They average 5.8 volts. The voltage NEEDS to be 6.3 and 12.6. You can calibrate a vintage tube tester all you want. If the heater voltage is not right, you will NEVER get the right gm value. I have customers complain that their tubes are not the same as what I see on my tester. They say they have a calibrated tube tester. I have 40 tube testers. On all of them I have an outside regulated DC power supply that feeds the tube tester the correct heater voltage.7. I dont check each and every tube for noise or tone. This is SUBJECTIVE and it is too time consuming. If you dont like the noise level or the tone we offer a hassle free refund policy.  International customers note:1. Please wait for us to invoice you for the correct amount. If you have purchased more than one item, we must calculate how much the shipping will be. Shipping will be HIGHER due to insurance and shipping methods needed for expensive item totals. If you are buying only one item this will not be an issue. 2. Under no circumstances will we state on a US customs a declared value of less than the sale price. This is an honesty issue. We are honest with everyone to the best of our ability to do so. We want you to trust that what we say is true. There cannot be that trust, if we make false statements knowingly to anyone. If your country has tariffs/taxes so high that they cause large numbers of normally honest folks to make false statements, we urge you to work for change of those laws.3 International buyers if you bought more than one item and want combined shipping it will ship in 2 days.4. And all the Angels sang because the heavenly music was playing and it was turned all the way up.  &nbs Listing and template services provided by inkFrog

Fender Champ Vintage Tube Set RCA 12ax7a 6V6GT 5Y3 Great Tone All USA made RCA’s. Tested on my Hickok 752. The 6v6 tests 850/575–beyond NOS. The 5Y3 tests strong at 500/400 on both plates . The Silvertone branded RCA made 12ax7a tests 83 on both plates (strong range) on my B&K 667. (12ax7s don’t test well on the Hickok). You will be thrilled with these tubes. Buy with confidence. Please look at my other listings also. Thanks for looking.

Fender Champ Vintage Tube Set RCA 12ax7a 6V6GT 5Y3 Great Tone All USA made RCA’s. Tested on my Hickok 752. The 6v6 tests 850/575–beyond NOS. The 5Y3 tests strong at 500/400 on both plates . The Silvertone branded RCA made 12ax7a tests 83 on both plates (strong range) on my B&K 667. (12ax7s don’t test well on the Hickok). You will be thrilled with these tubes. Buy with confidence. Please look at my other listings also. Thanks for looking.

Fender Champ Vintage Tube Set RCA 12ax7a 6V6GT 5Y3 Great Tone All USA made RCA’s. Tested on my Hickok 752. The 6v6 tests 850/575–beyond NOS. The 5Y3 tests strong at 500/400 on both plates . The Silvertone branded RCA made 12ax7a tests 83 on both plates (strong range) on my B&K 667. (12ax7s don’t test well on the Hickok). You will be thrilled with these tubes. Buy with confidence. Please look at my other listings also. Thanks for looking.

  TUBE HUNTER VACUUM TUBE GEMS THESE ARE THE SPECIFICS OF THE TUBE/TUBES/PARTS FOR SALE THESE ARE THE TUBE/TUBES/PARTS FOR SALE:  MANUFACTURER:                              SYLVANIA PRODUCTION CITY:                                    USA TUBE TYPE:   5Y3 GT DESIGNATION:                                             AWESOME US RECTIFIER FENDER  ORIGINAL YEAR:   1958 MONTH:   WEEK 13 Date code match   SINGLE SILK SCREEN CONDITION %:                    100% MICA:   1 PLATES:   BLACK GM%:   120%, 119% SINGLE/PAIR/QUAD/MULTI:   SINGLE GETTER:                                                          TOP D  GETTER DATE CODE                                                    58-13   Normal 0 false false false EN-US X-NONE X-NONE Fender lost its juice? Rectify that situation with this awesome replacement. On my tester a B&K 747 tester:    Below 55 = BAD      55-65 = ?     65 -100 = Good     100-120+ = NOS     I want to see you happy with your purchase. I will never sell a tube that is below standard…… I have sold many tubes here on Ebay, and all my customers have been completely satisfied. I will work with you in good faith if there are any problems, or if you are unsatisfied in any way. I want your business now and in the future, so I assume you are the boss, and I am the employee. All tubes are tested for shorts, continuity, and emissions. I prefer PayPal. ALL CUSTOMERS PLEASE READ ALL NOTES BEFORE BUYING FROM ME !!1.  RETURNS: It is my highest desire that you are completely satisfied with your purchase from me. I will bend over backwards to make sure that you are a happy customer.If anything you buy from me is less than satisfactory, message me BEFORE you either open a case or hit the “item not as described” button.Sound quality is tremendously SUBJECTIVE. For tubes returned for noise or sound quality of any kind you pay for the shipping we refund the purchase. We refund the price of the item NOT THE SHIPPING COST. If we sent the wrong tube we will of course pay for return shipping. For any tubes that are DOA we require that you send a us a picture of the shipping box to show us the damage. We test EVERY tube sent out and none should be DOA unless broken in shipping.2.    PLEASE NOTE:  Tube silkscreen (lettering on the tubes) is VERY fragile. It can be wiped off and destroyed VERY easily. If you wipe off the silkscreen while handling the tube you diminish their value by up to 70%. DO NOT handle the tubes or hold them from the cylinder. ALWAYS hold them from the ENDS. If you are returning tubes and they are not in the same condition cosmetically I cannot give you a full refund. THIS IS VERY IMPORTANT.3.  UNLESS YOU MAKE ARRANGEMENTS WITH US BEFORE YOU PURCHASE, YOU MUST PAY FOR ITEMS PURCHASED WITHIN 2 DAYS OR A CASE WILL BE OPENED FOR AN UNPAID ITEM!!!4. TESTING: I test all tubes that I sell in one way or another, or I will state untested. I have a B&K 747 tube tester. This is a mutual conductance tester. It give a percentage value of gm for the tube under test and checks for shorts and grid emissions. I also use a Tektronix curve tracer for testing triodes. I give a number of evaluations for tubes. One evaluation is a screen shot of the tube with a high voltage applied to the plate. This helps the buyer see the linearity of the tube in question at the highest voltage the tube will see in a real circuit. The Curve tracer steps the triode through 10 gate/grid voltages starting with -10 volts and going to 0 volts. The lines show how the tube conducts throughout that range. At 0 volt the tube is at max conduction and is the top line on the display. It is easy at that point to take where that top line intersects the plate voltage, find the milliamp level and compare it to the datasheet. I give those numbers for you in the Item condition box. To further help the buyer I also include the Design values, for gm and ma readings in the table. This can then be compared to other tube sellers using inferior test methods such as Hickok,  Amplitrex, and other testers. The Tektronix curve tracer gives values within 3% of the actual value. The very best portable testers only can approach 10% accuracy.5.    Please note: The numbers given for gm are what I see on my tester. I DO NOT guarantee that you will see those numbers on your tester. I only guarantee that these tubes will test good, with no shorts, or gas, on a decent calibrated tester. I dont guarantee or imply anything else.6. VERY IMPORTANT!!! Vintage tube testers almost always, due to age, have VERY LOW HEATER VOLTAGES!!!  Every tester I have ever bought is below 6 volts when selecting 6.3 volts. They average 5.8 volts. The voltage NEEDS to be 6.3 and 12.6. You can calibrate a vintage tube tester all you want. If the heater voltage is not right, you will NEVER get the right gm value. I have customers complain that their tubes are not the same as what I see on my tester. They say they have a calibrated tube tester. I have 40 tube testers. On all of them I have an outside regulated DC power supply that feeds the tube tester the correct heater voltage.7. I dont check each and every tube for noise or tone. This is SUBJECTIVE and it is too time consuming. If you dont like the noise level or the tone we offer a hassle free refund policy.  International customers note:1. Please wait for us to invoice you for the correct amount. If you have purchased more than one item, we must calculate how much the shipping will be. Shipping will be HIGHER due to insurance and shipping methods needed for expensive item totals. If you are buying only one item this will not be an issue. 2. Under no circumstances will we state on a US customs a declared value of less than the sale price. This is an honesty issue. We are honest with everyone to the best of our ability to do so. We want you to trust that what we say is true. There cannot be that trust, if we make false statements knowingly to anyone. If your country has tariffs/taxes so high that they cause large numbers of normally honest folks to make false statements, we urge you to work for change of those laws.3 International buyers if you bought more than one item and want combined shipping it will ship in 2 days.4. And all the Angels sang because the heavenly music was playing and it was turned all the way up.  &nbs Listing and template services provided by inkFrog

  TUBE HUNTER VACUUM TUBE GEMS THESE ARE THE SPECIFICS OF THE TUBE/TUBES/PARTS FOR SALE THESE ARE THE TUBE/TUBES/PARTS FOR SALE:  MANUFACTURER:                              SYLVANIA PRODUCTION CITY:                                    USA TUBE TYPE:   5Y3 GT DESIGNATION:                                             AWESOME US RECTIFIER FENDER  ORIGINAL YEAR:   1958 MONTH:   WEEK 13 Date code match   SINGLE SILK SCREEN CONDITION %:                    100% MICA:   1 PLATES:   BLACK GM%:   120%, 119% SINGLE/PAIR/QUAD/MULTI:   SINGLE GETTER:                                                          TOP D  GETTER DATE CODE                                                    58-13   Normal 0 false false false EN-US X-NONE X-NONE Fender lost its juice? Rectify that situation with this awesome replacement. On my tester a B&K 747 tester:    Below 55 = BAD      55-65 = ?     65 -100 = Good     100-120+ = NOS     I want to see you happy with your purchase. I will never sell a tube that is below standard…… I have sold many tubes here on Ebay, and all my customers have been completely satisfied. I will work with you in good faith if there are any problems, or if you are unsatisfied in any way. I want your business now and in the future, so I assume you are the boss, and I am the employee. All tubes are tested for shorts, continuity, and emissions. I prefer PayPal. ALL CUSTOMERS PLEASE READ ALL NOTES BEFORE BUYING FROM ME !!1.  RETURNS: It is my highest desire that you are completely satisfied with your purchase from me. I will bend over backwards to make sure that you are a happy customer.If anything you buy from me is less than satisfactory, message me BEFORE you either open a case or hit the “item not as described” button.Sound quality is tremendously SUBJECTIVE. For tubes returned for noise or sound quality of any kind you pay for the shipping we refund the purchase. We refund the price of the item NOT THE SHIPPING COST. If we sent the wrong tube we will of course pay for return shipping. For any tubes that are DOA we require that you send a us a picture of the shipping box to show us the damage. We test EVERY tube sent out and none should be DOA unless broken in shipping.2.    PLEASE NOTE:  Tube silkscreen (lettering on the tubes) is VERY fragile. It can be wiped off and destroyed VERY easily. If you wipe off the silkscreen while handling the tube you diminish their value by up to 70%. DO NOT handle the tubes or hold them from the cylinder. ALWAYS hold them from the ENDS. If you are returning tubes and they are not in the same condition cosmetically I cannot give you a full refund. THIS IS VERY IMPORTANT.3.  UNLESS YOU MAKE ARRANGEMENTS WITH US BEFORE YOU PURCHASE, YOU MUST PAY FOR ITEMS PURCHASED WITHIN 2 DAYS OR A CASE WILL BE OPENED FOR AN UNPAID ITEM!!!4. TESTING: I test all tubes that I sell in one way or another, or I will state untested. I have a B&K 747 tube tester. This is a mutual conductance tester. It give a percentage value of gm for the tube under test and checks for shorts and grid emissions. I also use a Tektronix curve tracer for testing triodes. I give a number of evaluations for tubes. One evaluation is a screen shot of the tube with a high voltage applied to the plate. This helps the buyer see the linearity of the tube in question at the highest voltage the tube will see in a real circuit. The Curve tracer steps the triode through 10 gate/grid voltages starting with -10 volts and going to 0 volts. The lines show how the tube conducts throughout that range. At 0 volt the tube is at max conduction and is the top line on the display. It is easy at that point to take where that top line intersects the plate voltage, find the milliamp level and compare it to the datasheet. I give those numbers for you in the Item condition box. To further help the buyer I also include the Design values, for gm and ma readings in the table. This can then be compared to other tube sellers using inferior test methods such as Hickok,  Amplitrex, and other testers. The Tektronix curve tracer gives values within 3% of the actual value. The very best portable testers only can approach 10% accuracy.5.    Please note: The numbers given for gm are what I see on my tester. I DO NOT guarantee that you will see those numbers on your tester. I only guarantee that these tubes will test good, with no shorts, or gas, on a decent calibrated tester. I dont guarantee or imply anything else.6. VERY IMPORTANT!!! Vintage tube testers almost always, due to age, have VERY LOW HEATER VOLTAGES!!!  Every tester I have ever bought is below 6 volts when selecting 6.3 volts. They average 5.8 volts. The voltage NEEDS to be 6.3 and 12.6. You can calibrate a vintage tube tester all you want. If the heater voltage is not right, you will NEVER get the right gm value. I have customers complain that their tubes are not the same as what I see on my tester. They say they have a calibrated tube tester. I have 40 tube testers. On all of them I have an outside regulated DC power supply that feeds the tube tester the correct heater voltage.7. I dont check each and every tube for noise or tone. This is SUBJECTIVE and it is too time consuming. If you dont like the noise level or the tone we offer a hassle free refund policy.  International customers note:1. Please wait for us to invoice you for the correct amount. If you have purchased more than one item, we must calculate how much the shipping will be. Shipping will be HIGHER due to insurance and shipping methods needed for expensive item totals. If you are buying only one item this will not be an issue. 2. Under no circumstances will we state on a US customs a declared value of less than the sale price. This is an honesty issue. We are honest with everyone to the best of our ability to do so. We want you to trust that what we say is true. There cannot be that trust, if we make false statements knowingly to anyone. If your country has tariffs/taxes so high that they cause large numbers of normally honest folks to make false statements, we urge you to work for change of those laws.3 International buyers if you bought more than one item and want combined shipping it will ship in 2 days.4. And all the Angels sang because the heavenly music was playing and it was turned all the way up.  &nbs Listing and template services provided by inkFrog

  TUBE HUNTER VACUUM TUBE GEMS THESE ARE THE SPECIFICS OF THE TUBE/TUBES/PARTS FOR SALE THESE ARE THE TUBE/TUBES/PARTS FOR SALE:  MANUFACTURER:                              CBS PRODUCTION CITY:                                    USA TUBE TYPE:   5Y3 GT DESIGNATION:                                             AWESOME US RECTIFIER FENDER  ORIGINAL YEAR:   1950s MONTH:     Date code match   SINGLE SILK SCREEN CONDITION %:                    100% MICA:   1 PLATES:   BLACK GM%:   120%, 119% SINGLE/PAIR/QUAD/MULTI:   SINGLE GETTER:                                                           D  GETTER DATE CODE                                                         DTOCK PHOTOS Normal 0 false false false EN-US X-NONE X-NONE Fender lost its juice? Rectify that situation with this awesome replacement. On my tester a B&K 747 tester:    Below 55 = BAD      55-65 = ?     65 -100 = Good     100-120+ = NOS     I want to see you happy with your purchase. I will never sell a tube that is below standard…… I have sold many tubes here on Ebay, and all my customers have been completely satisfied. I will work with you in good faith if there are any problems, or if you are unsatisfied in any way. I want your business now and in the future, so I assume you are the boss, and I am the employee. All tubes are tested for shorts, continuity, and emissions. I prefer PayPal. ALL CUSTOMERS PLEASE READ ALL NOTES BEFORE BUYING FROM ME !! 1.  RETURNS: It is my highest desire that you are completely satisfied with your purchase from me. I will bend over backwards to make sure that you are a happy customer. If anything you buy from me is less than satisfactory, message me BEFORE you either open a case or hit the “item not as described” button. Sound quality is tremendously SUBJECTIVE. For tubes returned for noise or sound quality of any kind you pay for the shipping we refund the purchase. We refund the price of the item NOT THE SHIPPING COST. If we sent the wrong tube we will of course pay for return shipping. For any tubes that are DOA we require that you send a us a picture of the shipping box to show us the damage. We test EVERY tube sent out and none should be DOA unless broken in shipping. 2.    PLEASE NOTE:  Tube silkscreen (lettering on the tubes) is VERY fragile. It can be wiped off and destroyed VERY easily. If you wipe off the silkscreen while handling the tube you diminish their value by up to 70%. DO NOT handle the tubes or hold them from the cylinder. ALWAYS hold them from the ENDS. If you are returning tubes and they are not in the same condition cosmetically I cannot give you a full refund. THIS IS VERY IMPORTANT. 3.  UNLESS YOU MAKE ARRANGEMENTS WITH US BEFORE YOU PURCHASE, YOU MUST PAY FOR ITEMS PURCHASED WITHIN 2 DAYS OR A CASE WILL BE OPENED FOR AN UNPAID ITEM!!! 4. TESTING: I test all tubes that I sell in one way or another, or I will state untested. I have a B&K 747 tube tester. This is a mutual conductance tester. It give a percentage value of gm for the tube under test and checks for shorts and grid emissions. I also use a Tektronix curve tracer for testing triodes. I give a number of evaluations for tubes. One evaluation is a screen shot of the tube with a high voltage applied to the plate. This helps the buyer see the linearity of the tube in question at the highest voltage the tube will see in a real circuit. The Curve tracer steps the triode through 10 gate/grid voltages starting with -10 volts and going to 0 volts. The lines show how the tube conducts throughout that range. At 0 volt the tube is at max conduction and is the top line on the display. It is easy at that point to take where that top line intersects the plate voltage, find the milliamp level and compare it to the datasheet. I give those numbers for you in the Item condition box. To further help the buyer I also include the Design values, for gm and ma readings in the table. This can then be compared to other tube sellers using inferior test methods such as Hickok,  Amplitrex, and other testers. The Tektronix curve tracer gives values within 3% of the actual value. The very best portable testers only can approach 10% accuracy.5.    Please note: The numbers given for gm are what I see on my tester. I DO NOT guarantee that you will see those numbers on your tester. I only guarantee that these tubes will test good, with no shorts, or gas, on a decent calibrated tester. I dont guarantee or imply anything else. 6. VERY IMPORTANT!!! Vintage tube testers almost always, due to age, have VERY LOW HEATER VOLTAGES!!!  Every tester I have ever bought is below 6 volts when selecting 6.3 volts. They average 5.8 volts. The voltage NEEDS to be 6.3 and 12.6. You can calibrate a vintage tube tester all you want. If the heater voltage is not right, you will NEVER get the right gm value. I have customers complain that their tubes are not the same as what I see on my tester. They say they have a calibrated tube tester. I have 40 tube testers. On all of them I have an outside regulated DC power supply that feeds the tube tester the correct heater voltage. 7. I dont check each and every tube for noise or tone. This is SUBJECTIVE and it is too time consuming. If you dont like the noise level or the tone we offer a hassle free refund policy.  International customers note: 1. Please wait for us to invoice you for the correct amount. If you have purchased more than one item, we must calculate how much the shipping will be. Shipping will be HIGHER due to insurance and shipping methods needed for expensive item totals. If you are buying only one item this will not be an issue. 2. Under no circumstances will we state on a US customs a declared value of less than the sale price. This is an honesty issue. We are honest with everyone to the best of our ability to do so. We want you to trust that what we say is true. There cannot be that trust, if we make false statements knowingly to anyone. If your country has tariffs/taxes so high that they cause large numbers of normally honest folks to make false statements, we urge you to work for change of those laws. 3 International buyers if you bought more than one item and want combined shipping it will ship in 2 days. 4. And all the Angels sang because the heavenly music was playing and it was turned all the way up.   Listing and template services provided by inkFrog