ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

Pair of Celestion HF1003 Type T3538 Dome Tweeters 8 Ohm from Ditton 110 Speakers These tweeters are in good working condition. Sounds great. Comes from a pair of Ditton 110 speakers that is being parted out. Please see pictures for cosmetic condition. I have woofers listed separately.

ORIGINAL MEMBRAN-HOCHTÖNER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS mit neuer SchwingspuleZusammensetzung: MYLAR Farbe: Transparent Montageempfehlungen Befestigen Sie die Membran am Magneten, indem Sie kleine Punkte Holzleim um den Umfang der Membran auftragen, um zu verhindern, dass Klebstoff zwischen die Spule und den Luftspalt des Magneten eindringt. Positionieren Sie die Membran direkt auf dem Magneten. Sobald dieser Schritt abgeschlossen ist, tragen Sie ebenfalls Klebepunkte auf der gesamten Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen austreten. Kleben Sie alles mit leichtem Druck zusammen und verlöten Sie dann die alten roten und schwarzen Verbindungskabel mit den neuen. Während der Kleber aushärtet, schließen Sie den Hochtöner an einen Verstärker mit geringer Leistung an und spielen Sie ein Musikstück mit Höhen ab oder verwenden Sie eine Frequenzerzeugungs-App, um die Zentrierung zu testen. Wichtige Hinweise:Ein roter Punkt an der Seite der Membran, der sich an einem der beiden Anschlüsse befindet, zeigt positiv an.Isolieren Sie die Stelle des Kabels zwischen der Abdeckung und dem Magneten mit einem Papieretikett oder einem kleinen Stück Klebeband, um einen falschen Kontakt zu vermeiden. Englisch :Montageempfehlungen Befestigen Sie die Membran am Magneten, indem Sie am Rand der Membran kleine Punkte Holzleim auftragen, um zu verhindern, dass Klebstoff zwischen Spule und Magnetspalt eindringt. Positionieren Sie die Membran direkt auf dem Magneten. Sobald dieser Schritt abgeschlossen ist, tragen Sie Klebepunkte auf die gesamte Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen führen. Drücken Sie leicht, um die Baugruppe zu verbinden, und löten Sie dann die alten roten und schwarzen Verbindungskabel an die neuen. Während der Kleber aushärtet, schließen Sie den Hochtöner an einen Verstärker mit geringer Leistung an und spielen Sie ein Musikstück mit hohen Frequenzen ab oder verwenden Sie eine Frequenzgenerator-App, um die Ausrichtung zu testen. Wichtige Hinweise:Ein roter Punkt an der Seite der Membran, der sich an einem der beiden Anschlüsse befindet, zeigt das Plus an.Isolieren Sie den Kabelbereich zwischen der Abdeckung und dem Magneten mit einem Papieretikett oder einem kleinen Stück Klebeband, um Kurzschlüsse zu vermeiden. Spanisch:Empfehlungen von Montaje Platzieren Sie das Diafragma al imán mit einigen Pegamento-Punkten, damit es entlang der Kante des Diafragmas angebracht wird und verhindert wird, dass das Pegamento zwischen der Spule und dem Entrehierro del Imán eindringt. Sprechen Sie direkt mit dem Diafragma über den Imán. Sobald dies abgeschlossen war, heften Sie sich an den Kartonschutz. Führen Sie die Verbindungskabel mit einem der Stifte durch die Anschlüsse, sodass sie nach außen gelangen. Durch leichtes Drücken werden die Stecker und Stecker, inklusive der alten roten und schwarzen Verbindungskabel, mit den neuen verbunden. Nachdem der Ton trocken ist, schließen Sie den Hochtöner an einen Verstärker mit geringer Leistung an und reproduzieren Sie ein Musikstück mit hohen Frequenzen oder verwenden Sie eine Anwendung zur Frequenzerzeugung, um die Ausrichtung zu testen. Wichtige Hinweise:Ein roter Punkt an der Seite des Diafragmas, der an einem der Anschlüsse angebracht ist, zeigt das Positiv an.Befestigen Sie den Bereich des Kabels zwischen der Schutzvorrichtung und dem Gehäuse mit einem Papieretikett oder einem kleinen Stück Klebeband, um versehentlichen Kontakt zu vermeiden. Italienisch:Lieferung durch Montaggio Das Diaframma mit dem Magneten mit Piccoli-Kleberspitze durchtrennen, indem Legno auf den Rand des Diaframmas aufgetragen wird, um zu verhindern, dass der Kleber durch die Spule und die Zwischenräume des Magneten eindringt. Positionieren Sie die Membran direkt auf dem Magneten. Nach einem kompletten Voltato dieses Durchgangs die Klebepunkte auf alle Kartonumschläge auftragen. Mit einem Stift geht das Schicksal durch den Verbindungskanal durch die Quelle, auf diese Weise bewegt es sich nach vorne. Bereiten Sie sich leicht darauf vor, den Einsatz, der zu den roten und schwarzen Anschlüssen hinzugefügt wurde, durch neue einzubinden. Schließen Sie während der Tonaufnahme den Hochtöner an einen Bassverstärker an und reproduzieren Sie einen Musikklang mit hohen Frequenzen oder nutzen Sie eine App zur Frequenzgenerierung, um die Mitte zu testen. Wichtiger Hinweis:Ein roter Punkt an der Seite des Rahmens, der sich an einem der Anschlüsse befindet, zeigt an, dass es positiv ist.Isolieren Sie den Bereich des Kabels nach der Abdeckung und dem Magneten mit einem Kartenetikett oder einem Piccolo-Pin auf dem Aufkleber, um mögliche versehentliche Kontakte zu vermeiden.Sobald dieser Schritt abgeschlossen ist, tragen Sie ebenfalls Klebepunkte auf der gesamten Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen austreten. Kleben Sie alles mit leichtem Druck zusammen und verlöten Sie dann die alten roten und schwarzen Verbindungskabel mit den neuen. Sobald dieser Schritt abgeschlossen ist, tragen Sie Klebepunkte auf die gesamte Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen führen. Drücken Sie leicht, um die Baugruppe zu verbinden, und löten Sie dann die alten roten und schwarzen Verbindungskabel an die neuen. Nach einem kompletten Voltato dieses Durchgangs die Klebepunkte auf alle Kartonumschläge auftragen. Mi

Celestion SL6 Tweeter - 1 Only - Part# T3506 Please note listing is for one Condition is Used. Tweeter in excellent condition Everything has been tested and verified as working as it should Tested ohms at 6.3 ohms please verify your part number   ITEM / ITEMS CONDITION      Please see photos for condition and look closely as we do our best to get the flaws in pictures sometimes it’s extremely hard to get them to come thru on photos.   More photos are always available by contact if you wish, so feel free to contact anytime.     PLEASE FEEL FREE TO CONTACT US ANYTIME IF YOU HAVE ANY QUESTIONS ABOUT THE ITEM OR ITEMS LISTED AS IT’S BEST TO ASK PRIOR TO BIDDING OR PURCHASING THEN TO DEAL WITH IT AFTERWARDS.    All our items will be double checked to insure items are as posted. We take great pride in insuring everything has been looked over prior to listing and verifying prior to shipping. As mistakes may happen in my post please reach out if you notice a problem or mistake.     SHIPPING PACKAGING WILL BE PROFESSIONALLY DONE WITH COMPLETE PROTECTION    **** CANADA **** SHIPPING IN CANADA ONLY NOT INCLUDING THE YUKON AND NWT   ****USA **** IF SHIPPING IS AVAIABLE TO THE USA FOR THIS ITEM IT WILL ONLY BE TO THE LOWER 48 STATES   WE ONLY USE CANADA POST FOR THE ITEMS THAT THEY CAN HANDLE UP TO A CERTAIN SIZE AND WEIGHT WISE. DIFFERENT SHIPPER MAY BE REQUIRED FOR LARGER AND HEAVIER ITEMS.   NO INSURANCE IS ADDED TO SHIPMENTS ….. IF YOU WANT IT INSURRED PLEASE CONTACT PRIOR TO PURCHASING SO COSTS ARE ADDED …. ALL ITEMS ARE SHIPPED AT SOLD PRICE LESS SHIPPING COSTS     PAYMENT INFORMATION?  - Please pay for your items within 2 days after the auction has ended.  - Please insure shipping address is correct, all steps will accelerate the delivery. - Please contact us for details if you want to purchase more items as it may save money on combine shipping. IN MOST CASES AUDIO MUST BE SHIPPED AS IS BUT PARTS CAN BE IN MOST CASE PENDING ON SIZE AND WEIGHT. CONDITION AND FEEDBACK All our items will be double checked to insure items are as posted. We take great pride in insuring everything has been looked over prior to listing and verifying prior to shipping. As mistakes may happen in my post please reach out if you notice a problem or mistake. *** PLEASE CONTACT BEFORE LEAVING ANY FEEDBACK IF UNHAPPY *** IF YOU DON’T POINT OUT A PROBLEM OR MISTAKE, WE CAN’T IMPROVE OUR SERVICE AND COMITTMENT     THANK YOU FOR STOPPING BY

ORIGINAL MEMBRAN-HOCHTÖNER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS mit neuer SchwingspuleZusammensetzung: MYLAR Farbe: Transparent Montageempfehlungen Befestigen Sie die Membran am Magneten, indem Sie kleine Punkte Holzleim um den Umfang der Membran auftragen, um zu verhindern, dass Klebstoff zwischen die Spule und den Luftspalt des Magneten eindringt. Positionieren Sie die Membran direkt auf dem Magneten. Sobald dieser Schritt abgeschlossen ist, tragen Sie ebenfalls Klebepunkte auf der gesamten Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen austreten. Kleben Sie alles mit leichtem Druck zusammen und verlöten Sie dann die alten roten und schwarzen Verbindungskabel mit den neuen. Während der Kleber aushärtet, schließen Sie den Hochtöner an einen Verstärker mit geringer Leistung an und spielen Sie ein Musikstück mit Höhen ab oder verwenden Sie eine Frequenzerzeugungs-App, um die Zentrierung zu testen. Wichtige Hinweise:Ein roter Punkt an der Seite der Membran, der sich an einem der beiden Anschlüsse befindet, zeigt positiv an.Isolieren Sie die Stelle des Kabels zwischen der Abdeckung und dem Magneten mit einem Papieretikett oder einem kleinen Stück Klebeband, um einen falschen Kontakt zu vermeiden. Englisch :Montageempfehlungen Befestigen Sie die Membran am Magneten, indem Sie am Rand der Membran kleine Punkte Holzleim auftragen, um zu verhindern, dass Klebstoff zwischen Spule und Magnetspalt eindringt. Positionieren Sie die Membran direkt auf dem Magneten. Sobald dieser Schritt abgeschlossen ist, tragen Sie Klebepunkte auf die gesamte Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen führen. Drücken Sie leicht, um die Baugruppe zu verbinden, und löten Sie dann die alten roten und schwarzen Verbindungskabel an die neuen. Während der Kleber aushärtet, schließen Sie den Hochtöner an einen Verstärker mit geringer Leistung an und spielen Sie ein Musikstück mit hohen Frequenzen ab oder verwenden Sie eine Frequenzgenerator-App, um die Ausrichtung zu testen. Wichtige Hinweise:Ein roter Punkt an der Seite der Membran, der sich an einem der beiden Anschlüsse befindet, zeigt das Plus an.Isolieren Sie den Kabelbereich zwischen der Abdeckung und dem Magneten mit einem Papieretikett oder einem kleinen Stück Klebeband, um Kurzschlüsse zu vermeiden. Spanisch:Empfehlungen von Montaje Platzieren Sie das Diafragma al imán mit einigen Pegamento-Punkten, damit es entlang der Kante des Diafragmas angebracht wird und verhindert wird, dass das Pegamento zwischen der Spule und dem Entrehierro del Imán eindringt. Sprechen Sie direkt mit dem Diafragma über den Imán. Sobald dies abgeschlossen war, heften Sie sich an den Kartonschutz. Führen Sie die Verbindungskabel mit einem der Stifte durch die Anschlüsse, sodass sie nach außen gelangen. Durch leichtes Drücken werden die Stecker und Stecker, inklusive der alten roten und schwarzen Verbindungskabel, mit den neuen verbunden. Nachdem der Ton trocken ist, schließen Sie den Hochtöner an einen Verstärker mit geringer Leistung an und reproduzieren Sie ein Musikstück mit hohen Frequenzen oder verwenden Sie eine Anwendung zur Frequenzerzeugung, um die Ausrichtung zu testen. Wichtige Hinweise:Ein roter Punkt an der Seite des Diafragmas, der an einem der Anschlüsse angebracht ist, zeigt das Positiv an.Befestigen Sie den Bereich des Kabels zwischen der Schutzvorrichtung und dem Gehäuse mit einem Papieretikett oder einem kleinen Stück Klebeband, um versehentlichen Kontakt zu vermeiden. Italienisch:Lieferung durch Montaggio Das Diaframma mit dem Magneten mit Piccoli-Kleberspitze durchtrennen, indem Legno auf den Rand des Diaframmas aufgetragen wird, um zu verhindern, dass der Kleber durch die Spule und die Zwischenräume des Magneten eindringt. Positionieren Sie die Membran direkt auf dem Magneten. Nach einem kompletten Voltato dieses Durchgangs die Klebepunkte auf alle Kartonumschläge auftragen. Mit einem Stift geht das Schicksal durch den Verbindungskanal durch die Quelle, auf diese Weise bewegt es sich nach vorne. Bereiten Sie sich leicht darauf vor, den Einsatz, der zu den roten und schwarzen Anschlüssen hinzugefügt wurde, durch neue einzubinden. Schließen Sie während der Tonaufnahme den Hochtöner an einen Bassverstärker an und reproduzieren Sie einen Musikklang mit hohen Frequenzen oder nutzen Sie eine App zur Frequenzgenerierung, um die Mitte zu testen. Wichtiger Hinweis:Ein roter Punkt an der Seite des Rahmens, der sich an einem der Anschlüsse befindet, zeigt an, dass es positiv ist.Isolieren Sie den Bereich des Kabels nach der Abdeckung und dem Magneten mit einem Kartenetikett oder einem Piccolo-Pin auf dem Aufkleber, um mögliche versehentliche Kontakte zu vermeiden.Sobald dieser Schritt abgeschlossen ist, tragen Sie ebenfalls Klebepunkte auf der gesamten Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen austreten. Kleben Sie alles mit leichtem Druck zusammen und verlöten Sie dann die alten roten und schwarzen Verbindungskabel mit den neuen. Sobald dieser Schritt abgeschlossen ist, tragen Sie Klebepunkte auf die gesamte Kartonabdeckung auf. Führen Sie die beiden Anschlusskabel mit einer Pinzette durch die beiden Löcher, sodass sie nach außen führen. Drücken Sie leicht, um die Baugruppe zu verbinden, und löten Sie dann die alten roten und schwarzen Verbindungskabel an die neuen. Nach einem kompletten Voltato dieses Durchgangs die Klebepunkte auf alle Kartonumschläge auftragen. Mi

PLEASE DO NOT PURCHASE UNLESS YOU HAVE BEEN DIRECTED TO DO SOTHIS IS STRICTLY FOR L5N3B9 - THX PLEASE DO NOT PURCHASE UNLESS YOU HAVE BEEN DIRECTED TO DO SOTHIS IS STRICTLY FOR L5N3B9 - THX PLEASE DO NOT PURCHASE UNLESS YOU HAVE BEEN DIRECTED TO DO SOTHIS IS STRICTLY FOR L5N3B9 - THX Celestion Tweeter 16ohm HG1300 16 ? ENGLAND EXCELLENTCelestion Tweeter 16ohm HG1300 16 ? ENGLAND EXCELLENT Listing is for ONE unitPurchase TWO for one PAIR Fully tested and work and sound great, no issuesAll original OEM vintage with original Celestion coilsDCR measured at 13 ? these are 16 ? rated driversSimilar to HF1300 T1295These are HG1300 with their original Celestion16 ohm voice coils diaphragms Spendor BC1 BC-1, Rogers, LS3/6, Ditton 25, B&W DDM2 DM3 This listing is for 1 single driver so if you need a pair, please purchase a quantity of 2 units This listing is for 1 single driver so if you need a pair, please purchase a quantity of 2 unitsThis listing is for 1 single driver so if you need a pair, please purchase a quantity of 2 units Shipped fully insured with tracking. Packaged up for definite safe delivery to your location.

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

This is a .75 metal dome tweeter from a KEF/Celestion F15 loudspeaker. It works and sounds as it should, but Im parting these out due to anoter injured tweeter. Please see pictures and do the appropriate research if you plan to use this in another system. Comes as shown. I have another woofer and tweeter as well as trim rings and crossovers for the same speakers. Ships to US48 only. Thanks for looking.

Good working condition, stored safely for a long time. Pair comes exactly as shown, see pictures. ... Description Pair of 2 Celestion Ditton 551 Speaker Tweeters T-2936 / T2936 #1 DETAILS:  Good working condition, stored safely for a long time.  Pair comes exactly as shown, see pictures. KNOW WHAT YOU ARE BUYING, SEE PICTURES. DONT JUST BUY FROM ANYONE, KNOW WHO YOU CAN TRUST. REFERENCE:  Ben-W Click images to enlarge Payment Auction payments are expected within 48 hours of auctions end. If you have any questions or need additional time to make a payment for any reason, feel free to contact us via eBay messages. Shipping All items typically ship out within 24, after payment is received. Domestic US packages typically take between 2 to 10 business days to arrive, depending on which shipping method you chose during checkout. We ship Worldwide and International orders take approximately 3 to 4 weeks to arrive. Terms of Sale All sales are final, but 100% customer satisfaction is our main goal. If you have any issues with an item upon receiving it, please dont hesitate to contact us. We are here to help ! About Us We have over 10 years of experience in online sales with over 25,000 satisfied eBay customers on our sister eBay account (dasilva1079). In August of 2013, we started a new venture and decided to share our special finds with the world through this account. Contact Us If you have any questions we can be contacted via eBay messages, 24 hours a day, 7 days a week. All messages are guaranteed to receive a response within 24 hours, Pictures sell! Auctiva offers Free Image Hosting and Editing.300+ Listing Templates! Auctiva gets you noticed! The complete eBay Selling Solution. Track Page Views WithAuctivas Counter

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilComposition: Mylar Color: Transparent Mounting recommendations Secure the diaphragm to the magnet with small dots of wood glue applied around the perimeter of the diaphragm, to prevent glue from penetrating between the coil and the magnet air gap. Position the diaphragm directly on the magnet. Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. While the glue is setting, plug the tweeter into a low-power amp and play a piece of music with treble or use a frequency generation app to test centering. Important notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates positive.Insulate the location of the cable between the cover and the magnet with a paper label or a small piece of tape to avoid any false contact. English :Mounting Recommendations Attach the diaphragm to the magnet with small dots of wood glue applied around the edge of the diaphragm, to prevent glue from entering between the coil and the magnet gap. Position the diaphragm directly on the magnet. Once this step is complete, apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so they exit to the outside. Press lightly to bond the assembly, then solder the old red and black connection cables to the new ones. While the glue is setting, connect the tweeter to a low-power amplifier and play a piece of music with high frequencies or use a frequency generator app to test the alignment. Important Notes:A red dot on the side of the diaphragm, located on one of the two connectors, indicates the positive.Isolate the cable area between the cover and the magnet with a paper label or a small piece of tape to avoid any short circuit. Spanish:Recommendations from Montaje Place the diafragma al imán with a few pegamento points to make it apply along the edge of the diafragma, to avoid the pegamento penetrating between the coil and the entrehierro del imán. Talk directly to the diafragma sobre el imán. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. Now the audio is dry, connect the tweeter to a low power amplifier and reproduce a musical piece with high frequencies or use a frequency generating application to test the alignment. Important Notes:A red point on the side of the diafragma, attached to one of the connectors, indicates the positive.Leave the area of ??the cable between the protector and the imán with a paper label or a small trozo of adhesive tape to avoid accidental contact. Italian:Delivery by the Montaggio Fissate the diaframma with the magnet with piccoli point of glue by legno applied on the edge of the diaframma, to avoid the glue penetrates through the coil and the interstizio of the magnet. Position the diaphram directly on the magnet. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way it moves towards the front. Prepare lightly to include the insert, which has been added to the red and black connections with new ones. During the sound recording, connect the tweeter to a bass amplifier and reproduce a musical sound at high frequencies or use an app to generate the frequency to test the center. Important Note:A red point on the side of the frame, located on one of the connectors, indicates it is positive.Isolate the area of ??the cable following the cover and the magnet with a card label or a piccolo pin on the sticker to avoid possible accidental contacts.Once this step has been completed, also apply dots of glue all over the cardboard cover. Using tweezers, pass the two connection cables through the two holes so that they exit outwards. Use light pressure to glue everything together, then solder the old red and black connection cables to the new ones. Una vez completeado este paso, aplitos de pegamento por todo el protector de cardboard. With one of the pins, pass the connection cables through the connectors so that they reach the exterior. Press lightly to connect the connectors and connectors, including the old red and black connection cables, to the new ones. A complete voltato of this passaggio, apply the glue points to all the covers in cardboard. With a pin, fate passes through the connection channel through the source, in this way i

Good working condition, stored safely for a long time. Pair comes exactly as shown, see pictures. ... Description Pair of 2 Celestion Ditton 551 Speaker Tweeters T-2936 / T2936 #1 DETAILS:  Good working condition, stored safely for a long time.  Pair comes exactly as shown, see pictures. KNOW WHAT YOU ARE BUYING, SEE PICTURES. DONT JUST BUY FROM ANYONE, KNOW WHO YOU CAN TRUST. REFERENCE:  Ben-W Click images to enlarge Payment Auction payments are expected within 48 hours of auctions end. If you have any questions or need additional time to make a payment for any reason, feel free to contact us via eBay messages. Shipping All items typically ship out within 24, after payment is received. Domestic US packages typically take between 2 to 10 business days to arrive, depending on which shipping method you chose during checkout. We ship Worldwide and International orders take approximately 3 to 4 weeks to arrive. Terms of Sale All sales are final, but 100% customer satisfaction is our main goal. If you have any issues with an item upon receiving it, please dont hesitate to contact us. We are here to help ! About Us We have over 10 years of experience in online sales with over 25,000 satisfied eBay customers on our sister eBay account (dasilva1079). In August of 2013, we started a new venture and decided to share our special finds with the world through this account. Contact Us If you have any questions we can be contacted via eBay messages, 24 hours a day, 7 days a week. All messages are guaranteed to receive a response within 24 hours, Pictures sell! Auctiva offers Free Image Hosting and Editing.300+ Listing Templates! Auctiva gets you noticed! The complete eBay Selling Solution. Track Page Views WithAuctivas Counter

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: TransparentORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 4 OHMS with new voice coil Composition: Mylar  Color: Transparent

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilMaterial: Mylar Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: Clear

For sale is an excellent working Rogers Studio 1a tweeter in excellent condition. Info on magnet reads: FW27 39571 Celestion, please see pics. No shipping to Alaska, Hawaii and Puerto Rico. You will receive everything you see in the pictures, if it is not pictured then its not included. All items have an invisible hidden security mark. Please view pictures and ask any questions you might have. Have a nice day!

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: TransparentORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 4 OHMS with new voice coil Composition: Mylar  Color: Transparent

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilMaterial: Mylar Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: Clear

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: Mylar Color: TransparentORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 4 OHMS with new voice coil Composition: Mylar  Color: Transparent

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,668 OHMS with new voice coilMaterial: Mylar Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: ClearORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 8 OHMS with new voice coil Material: Mylar  Color: Clear

ORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,664 OHMS with new voice coilComposition: MYLAR Color: TransparentORIGINAL DIAPHRAGM TWEETER ROLA CELESTION HF2000 CELESTION DITTON 25,44,66 4 OHMS with new voice coil Composition: MYLAR  Color: Transparent