CCa E88CC E188CC 6922 SIEMENS HALSKE MUNICH GERMANY MATCHED PAIR 2 Pcs NOSEXTRA BALANCED !!! EXTRA MATCHED !!!NOS Siemens Halske CCa = E88CC 6922 Grey-Shield HOLY GRAILS 1963 and 1964ACID CODES :Code: A? 1? 3A and A? 1? 4E O-getter,one stage geter ,gray shield ,The gray shieldSTA do you think how many CCa tubes of this type needed to be measured to select this pair?MUCH MORE THAN YOU THINK !!! Probably no one in this world has a pair of CCs like this because there are NO more of them !!This version with gold pins is professional and allows work of 10000 hours !!!!It is very difficult to pair 4 tubes and to keep each of them balanced. Before recording the characteristics, all CC tubes are aged for 72 hours in a specially made device and then tested and selected. For these 2 tubes it took over 50 tubes to select a that, you will admit it is very difficult. and theres no need to brag about those tubes - take a look on the net and everything will be clearwhy do I have to age them for 72 hours. Since I give the electrical characteristics of the tubes and for that to be correct, the CC tubes must be forced to work for at least 48 hours in order to equalize the working mode and only then the characteristics are recorded. the current Ia measured on that occasion does not have to be 16 mA and that is 100%, they can be higher and lower, within some limits - there are some on the NET, but it is important that the triodes in the balloon tubes CCa are as uniform as possible . And thats except Ia - mA quality which is primary for me and as a third reference, if I can, give the code .its nice to be harmonized due to the later exploitation of tubes-10000 hours.They are also tested for gas, short and leakageNote: The measurements were carried out with Neuberger RPM370 saw and guarantee for this measurement. The tester has its technical and electrical characteristics that participate in the activities and measuring tubes. Each tube is a special electric circuit that works in conjunction with the saw and this gives measured values. Power saws with classic rectifier and everything else and it has its own impedance, etc ... Digital testers can not give the same measurement results as the classical tester for impedance, reactance, capacitance, conductance, the mode power supply - Switching etc . Tested for NEUBERGER RPM370,Ua=100V,Ug=-1.2V,Ig=16mA=100% tubes Ia = 20/19mA and Ia = 19/20 mA

3 great sounding audio tubes E88CC, Valvo and Siemens & Halske Good test on Funke W19 with matching results:11.0 / 11.5 - 11.0 / 11.5 - 11.5 / 11.0 mAgood starts at 6 mA Shipping cost within Germany by DHL: 5,49 EuroWithin EU: 13,99 EuroPlease ask for shipping cost to your country outside EUPlease watch my other auctions for combined shipping. Privatverkauf unter Ausschluss der Gewährleistung.

Coppia di valvole Siemens nos ECC88 nib. Acquistate NOS e praticamente mai utilizzate. Funzionamento perfetto.

SIEMENS ECC88CC Cca 6DJ8 CV2492 6922 E88CC GOLD PINS 5 x PIECES ALL TAKEN FROM DECOMMISSIONED TEST EQUIPEMENT AS IN LAST LAST TWO PICTURES. UNABLE TO TEST AS I DO NOT HAVE A TESTER SELLING AS UNTESTED WITH NO RETURNS FEEL FREE TO ASK ANY QUESTIONS PLEASE VIEW MY OTHER VALVES FOR SALE.

SIEMENS ECC88CC Cca N74 6DJ8 CV2492 6922 E88CC GOLD PIN 16 x PIECES ALL TAKEN FROM DECOMMISSIONED SIEMENS TEST EQUIPEMENT AS IN LAST LAST TWO PICTURES. UNABLE TO TEST AS I DO NOT HAVE A TESTER SELLING AS UNTESTED WITH NO RETURNS FEEL FREE TO ASK ANY QUESTIONS PLEASE VIEW MY OTHER VALVES FOR SALE.

CCa SIEMENS GEPRÜFT AUF RPG FUNKE W19: 13/12mA - GUT AB 6mA -

CCa E88CC E188CC 6922 SIEMENS HALSKE MUNICH GERMANY MATCHED PAIR 2 Pcs NOSEXTRA BALANCED !!! EXTRA MATCHED !!!NOS Siemens Halske CCa = E88CC 6922 Grey-Shield HOLY GRAILS 1963 and 1964ACID CODES :Code: A? 1? 3A and A? 1? 4E O-getter,one stage geter ,gray shield ,The gray shieldSTA do you think how many CCa tubes of this type needed to be measured to select this pair?MUCH MORE THAN YOU THINK !!! Probably no one in this world has a pair of CCs like this because there are NO more of them !!This version with gold pins is professional and allows work of 10000 hours !!!!It is very difficult to pair 4 tubes and to keep each of them balanced. Before recording the characteristics, all CC tubes are aged for 72 hours in a specially made device and then tested and selected. For these 2 tubes it took over 50 tubes to select a that, you will admit it is very difficult. and theres no need to brag about those tubes - take a look on the net and everything will be clearwhy do I have to age them for 72 hours. Since I give the electrical characteristics of the tubes and for that to be correct, the CC tubes must be forced to work for at least 48 hours in order to equalize the working mode and only then the characteristics are recorded. the current Ia measured on that occasion does not have to be 16 mA and that is 100%, they can be higher and lower, within some limits - there are some on the NET, but it is important that the triodes in the balloon tubes CCa are as uniform as possible . And thats except Ia - mA quality which is primary for me and as a third reference, if I can, give the code .its nice to be harmonized due to the later exploitation of tubes-10000 hours.They are also tested for gas, short and leakageNote: The measurements were carried out with Neuberger RPM370 saw and guarantee for this measurement. The tester has its technical and electrical characteristics that participate in the activities and measuring tubes. Each tube is a special electric circuit that works in conjunction with the saw and this gives measured values. Power saws with classic rectifier and everything else and it has its own impedance, etc ... Digital testers can not give the same measurement results as the classical tester for impedance, reactance, capacitance, conductance, the mode power supply - Switching etc . Tested for NEUBERGER RPM370,Ua=100V,Ug=-1.2V,Ig=16mA=100% tubes Ia = 20/19mA and Ia = 19/20 mA

CCa E88CC E188CC 6922 SIEMENS HALSKE MUNICH GERMANY MATCHED QUAD 4 Pcs NOS Code: tubes A6 / 4G and A6 / 3I and A6 /4I and A6 / 4CO-getter,A-frame ,The chrome shieldMany e88cc tubes needed to pair this pair matched to several criteria: date of production - same series and electrical characteristics. such pairing is rareEXTRA MATCHED QUAD !!! EXTRA RARE!!!This version with gold pins is professional and allows work of 10000 hours !!!!It is very difficult to pair 4 tubes and to keep each of them balanced. Before recording the characteristics, all CC tubes are aged for 72 hours in a specially made device and then tested and selected. For these 4 tubes it took over 50 tubes to select a that, you will admit it is very difficult. and theres no need to brag about those tubes - take a look on the net and everything will be clearwhy do I have to age them for 72 hours. Since I give the electrical characteristics of the tubes and for that to be correct, the CC tubes must be forced to work for at least 48 hours in order to equalize the working mode and only then the characteristics are recorded. the current Ia measured on that occasion does not have to be 16 mA and that is 100%, they can be higher and lower, within some limits - there are some on the NET, but it is important that the triodes in the balloon tubes CCa are as uniform as possible . And thats except Ia - mA quality which is primary for me and as a third reference, if I can, give the code .its nice to be harmonized due to the later exploitation of tubes-10000 hours.They are also tested for gas, short and leakageNote: The measurements were carried out with Neuberger RPM370 saw and guarantee for this measurement. The tester has its technical and electrical characteristics that participate in the activities and measuring tubes. Each tube is a special electric circuit that works in conjunction with the saw and this gives measured values. Power saws with classic rectifier and everything else and it has its own impedance, etc ... Digital testers can not give the same measurement results as the classical tester for impedance, reactance, capacitance, conductance, the mode power supply - Switching etc . Tested for NEUBERGER RPM370,Ua=100V,Ug=-1.2V,Ig=16mA=100% two tubes Ia = 15/14 mA and two tubes Ia = 15/15 mA

SIEMENS E188CC/6922 same code GREY PLATTE 0 disc getterValves are tested. I have a HICKOK TV-3C/U tube tester .The measurements are of mutual conductance.The measures are REAL and are the average of five measurements.The object is to get the picture. The 100% of the tube is equal to 2500 micromhos.TUBE A 2000/2100 TUBEB 1800/1950 The valves were selected and output coupled at the following frequencies 20, 56, 125,320,750.2 k, 5 k, 12 k, 20.2 k. See the photos Attention please Read the following carefully before making purchases. I do not accept the return of the object for any reason. I repeat no reason. If your intention is to buy you must accept this condition. At the end of the auction do not make the payment. I will send you photos of how your valves will be packed. If you think the packaging is insufficient You can ask for the cancellation of the transaction that will be accepted by me.

CCa E88CC E188CC 6922 SIEMENS HALSKE MUNICH GERMANY MATCHED PAIR 2 Pcs NOSEXTRA BALANCED !!! EXTRA MATCHED !!!NOS Siemens Halske CCa = E88CC 6922 Grey-Shield HOLY GRAILS 1963 and 1964ACID CODES :Code: A? 1? 3A and A? 1? 4E O-getter,one stage geter ,gray shield ,The gray shieldSTA do you think how many CCa tubes of this type needed to be measured to select this pair?MUCH MORE THAN YOU THINK !!! Probably no one in this world has a pair of CCs like this because there are NO more of them !!This version with gold pins is professional and allows work of 10000 hours !!!!It is very difficult to pair 4 tubes and to keep each of them balanced. Before recording the characteristics, all CC tubes are aged for 72 hours in a specially made device and then tested and selected. For these 2 tubes it took over 50 tubes to select a that, you will admit it is very difficult. and theres no need to brag about those tubes - take a look on the net and everything will be clearwhy do I have to age them for 72 hours. Since I give the electrical characteristics of the tubes and for that to be correct, the CC tubes must be forced to work for at least 48 hours in order to equalize the working mode and only then the characteristics are recorded. the current Ia measured on that occasion does not have to be 16 mA and that is 100%, they can be higher and lower, within some limits - there are some on the NET, but it is important that the triodes in the balloon tubes CCa are as uniform as possible . And thats except Ia - mA quality which is primary for me and as a third reference, if I can, give the code .its nice to be harmonized due to the later exploitation of tubes-10000 hours.They are also tested for gas, short and leakageNote: The measurements were carried out with Neuberger RPM370 saw and guarantee for this measurement. The tester has its technical and electrical characteristics that participate in the activities and measuring tubes. Each tube is a special electric circuit that works in conjunction with the saw and this gives measured values. Power saws with classic rectifier and everything else and it has its own impedance, etc ... Digital testers can not give the same measurement results as the classical tester for impedance, reactance, capacitance, conductance, the mode power supply - Switching etc . Tested for NEUBERGER RPM370,Ua=100V,Ug=-1.2V,Ig=16mA=100% tubes Ia = 20/19mA and Ia = 19/20 mA

CCa E88CC E188CC 6922 SIEMENS HALSKE MUNICH GERMANY MATCHED QUAD 4 Pcs NOS Code: tubes A6 / 4G and A6 / 3I and A6 /4I and A6 / 4CO-getter,A-frame ,The chrome shieldMany e88cc tubes needed to pair this pair matched to several criteria: date of production - same series and electrical characteristics. such pairing is rareEXTRA MATCHED QUAD !!! EXTRA RARE!!!This version with gold pins is professional and allows work of 10000 hours !!!!It is very difficult to pair 4 tubes and to keep each of them balanced. Before recording the characteristics, all CC tubes are aged for 72 hours in a specially made device and then tested and selected. For these 4 tubes it took over 50 tubes to select a that, you will admit it is very difficult. and theres no need to brag about those tubes - take a look on the net and everything will be clearwhy do I have to age them for 72 hours. Since I give the electrical characteristics of the tubes and for that to be correct, the CC tubes must be forced to work for at least 48 hours in order to equalize the working mode and only then the characteristics are recorded. the current Ia measured on that occasion does not have to be 16 mA and that is 100%, they can be higher and lower, within some limits - there are some on the NET, but it is important that the triodes in the balloon tubes CCa are as uniform as possible . And thats except Ia - mA quality which is primary for me and as a third reference, if I can, give the code .its nice to be harmonized due to the later exploitation of tubes-10000 hours.They are also tested for gas, short and leakageNote: The measurements were carried out with Neuberger RPM370 saw and guarantee for this measurement. The tester has its technical and electrical characteristics that participate in the activities and measuring tubes. Each tube is a special electric circuit that works in conjunction with the saw and this gives measured values. Power saws with classic rectifier and everything else and it has its own impedance, etc ... Digital testers can not give the same measurement results as the classical tester for impedance, reactance, capacitance, conductance, the mode power supply - Switching etc . Tested for NEUBERGER RPM370,Ua=100V,Ug=-1.2V,Ig=16mA=100% two tubes Ia = 15/14 mA and two tubes Ia = 15/15 mA