1 Paar (2 St.) gepflegte Lautsprecher von Canton, Typ Combi 200, baugleich mit Plus S, schwarz, hochwertiges Holzgehäuse mit abgerundeten Ecken, tierfreier Nichtraucherhaushalt, Versand oder Abholung in Selters im Taunus möglich, ca. 10 min. von A3 Abfahrt Bad Camberg, schaut auch nach meinen anderen Angeboten, es lohnt sich

1 Paar (2 St.) gepflegte Lautsprecher von Canton, Typ Combi 200, baugleich mit Plus S, schwarz, hochwertiges Holzgehäuse mit abgerundeten Ecken, tierfreier Nichtraucherhaushalt, Versand oder Abholung in Selters im Taunus möglich, ca. 10 min. von A3 Abfahrt Bad Camberg, schaut auch nach meinen anderen Angeboten, es lohnt sich

Offered for your consideration is a CANTON 15mm dome tweeter that was original equipment in their Plus MX surround speakers, manufactured c.2003. The tweeter was epoxied to the back of the faceplate by CANTON, so the whole assembly must be replaced (which is simple to do as I’ll describe later). So, please see the large photos, measurements, and read the remaining description to decide if this capable high frequency driver is suitable for your needs. *Although the listing is written in singular to avoid any confusion, two (2) identical CANTON Plus MX tweeters are available at the time of this writing. Please choose if you’d like to buy one or both in the quantity field at the top of the listing. The shipping cost will be automatically calculated by eBay checkout. This tweeter is in clean, excellent condition. It has a flawless, dimple-free radiating surface well protected by the acoustically transparent wave-guide. Plus, the sturdy black plastic faceplate assembly has no scratches or cracks. And, I’ve left several inches of the +/- input wires soldered to the terminals for the new owner’s convenience when splicing-in to their speaker. Overall, this CANTON tweeter looks practically new. It’s been fully tested and sounds great—clear and strong output that goes deep into the beyond-audibility ‘sparkle’ zone with its 25kHz rating! And, I tested its DC resistance at 3.9-4.0?, consistent with a nominal 4 ohm driver rating. Lastly, the faceplate measures 3½” wide x just under 4?” high. Retrofitting to your CANTON MX speaker because of a blown or otherwise damaged tweeter is really easy to do: Remove grille by pulling at edge or corner with a sturdy safety pin or similar. Unscrew four woofer bolts, carefully pull woofer out and unplug the +/- wires; set aside cone side up. Remove the two screws flanking the tweeter. Pull the front fascia/baffle assembly back and cut the wires close to the magnet of the dead tweeter. Strip those wires back ½” or so, twist like-colors to the wires on the new tweeter and wrap each juncture with electrical tape. Reassemble and you’re done! As pictured and described, this CANTON Plus MX 15mm dome tweeter is offered at a competitive price. Terms of Sale: I encourage interested parties to ask any questions they may have about this listing before committing to purchase. Payment is due at checkout by PayPal or other accepted methods. U.S. mailing addresses will pay $4.95 for very carefully packed shipping via U.S. Postal Service with tracking and delivery confirmation. International purchases accepted only from those who are able to pay with PayPal, including shipping by U.S. Postal Service First Class Parcel Air Mail. Thanks for looking! *the cabinet sticker photo is presented only for donor model reference

Offered for your consideration is a CANTON 15mm dome tweeter that was original equipment in their Plus MX surround speakers, manufactured c.2003. The tweeter was epoxied to the back of the faceplate by CANTON, so the whole assembly must be replaced (which is simple to do as I’ll describe later). So, please see the large photos, measurements, and read the remaining description to decide if this capable high frequency driver is suitable for your needs. *Although the listing is written in singular to avoid any confusion, two (2) identical CANTON Plus MX tweeters are available at the time of this writing. Please choose if you’d like to buy one or both in the quantity field at the top of the listing. The shipping cost will be automatically calculated by eBay checkout. This tweeter is in clean, excellent condition. It has a flawless, dimple-free radiating surface well protected by the acoustically transparent wave-guide. Plus, the sturdy black plastic faceplate assembly has no scratches or cracks. And, I’ve left several inches of the +/- input wires soldered to the terminals for the new owner’s convenience when splicing-in to their speaker. Overall, this CANTON tweeter looks practically new. It’s been fully tested and sounds great—clear and strong output that goes deep into the beyond-audibility ‘sparkle’ zone with its 25kHz rating! And, I tested its DC resistance at 3.9-4.0?, consistent with a nominal 4 ohm driver rating. Lastly, the faceplate measures 3½” wide x just under 4?” high. Retrofitting to your CANTON MX speaker because of a blown or otherwise damaged tweeter is really easy to do: Remove grille by pulling at edge or corner with a sturdy safety pin or similar. Unscrew four woofer bolts, carefully pull woofer out and unplug the +/- wires; set aside cone side up. Remove the two screws flanking the tweeter. Pull the front fascia/baffle assembly back and cut the wires close to the magnet of the dead tweeter. Strip those wires back ½” or so, twist like-colors to the wires on the new tweeter and wrap each juncture with electrical tape. Reassemble and you’re done! As pictured and described, this CANTON Plus MX 15mm dome tweeter is offered at a competitive price. Terms of Sale: I encourage interested parties to ask any questions they may have about this listing before committing to purchase. Payment is due at checkout by PayPal or other accepted methods. U.S. mailing addresses will pay $4.95 for very carefully packed shipping via U.S. Postal Service with tracking and delivery confirmation. International purchases accepted only from those who are able to pay with PayPal, including shipping by U.S. Postal Service First Class Parcel Air Mail. Thanks for looking! *the cabinet sticker photo is presented only for donor model reference