Bang & Olufsen Beocenter 9000/9500/9300 Right panel with 7-segment display 45/46 Module 8002740/8002736 Upper right display panel for Beocenter 9000, 9500, 8000, 8500, and 9300 models. This part is the an A revision part number, but is interchangeable with all versions across all models above. Postage The part will be carefully packed, boxed, and sent promptly by recorded post. Returns and worldwide postage are available.

Bang & Olufsen BeoSound 4 FM radio PCB 85 module 8002415 FM module for all BeoSound 4 models Postage The module will be carefully packed in an antistatic bag, before being boxed ready for despatch by recorded post. International postage is available.

Bang & Olufsen Beocenter 9000/9500 Tuner FM/AM Module 10/17 8002715/8050093 FM, AM, RF, and IF decoder PCB with Tuner module for Beocenter 9000 models other than the 9300. For European/UK market. The tuner module is the single part recommended for replacement rather than repair in the service manual. Removed from a working Beocenter, and kept in warm storage. Postage The part will be carefully packed, boxed, and sent by recorded post. Worldwide postage is available.

Bang & Olufsen Beocenter 9300 Centre control panel 42 Module 8002750 For Beocenter 9300 only, as it lacks the level switch for earlier models. Parts available are Rev. F and g Postage The part will be carefully packed, boxed, and sent promptly by recorded post. Returns and worldwide postage are available.

Bang & Olufsen Aluminium lid 3162129 For various models Lower left aluminium cosmetic panel for Beomaster 6000 and Beocords 6000, 6002, 8000, 8002, 8004, and 9000 In good condition, but with a set of pitting scratches, and a few areas with rough edges – as shown in the photographs. Postage The part will be very carefully packed, and amply boxed ready for despatch by recorded post. A return and worldwide delivery are available.

Obseclec.com • 07753 241443 • Obscure Eclectics Parts UK delivery and 30-day returns included • worldwide delivery available • before and after sales enquiries: 07753 241443 BeoLab 4 Power supply module Part numbers Module number: PCB 2 Part number: 8002620 Board number: 6143556E Compatibility Fits BeoLab 4 and 4 PC Models Condition In fully tested, working condition Postage The part will be carefully packed and boxed, ready for despatch by recorded post. Worldwide delivery is available: the price shown applies to Europe only, and delivery further afield may attract a supplement. Enquire before purchase for further details. All items are promptly despatched, and carefully packed using a minimum of plastic packaging. See how we package parts-->

Obseclec.com • 07753 241443 • Obscure Eclectics Parts UK delivery and 30-day returns included • worldwide delivery available • before and after sales enquiries: 07753 241443 BeoSound 1 Power supply module 2 Part numbers Part number: 8006456, 8006898 Board number: 8002480 Compatibility This part is designed for the 2001-2011 Beosound 1, not its 2016 namesake. Fits all 200-240 V BeoSound 1 versions: types 2581, 2582, 2585, 2587, and 2590. Compatible with 100-130 V versions once jumper is fitted at J2: type 2583, 2584, and 2586. Condition The part is in fully tested, working condition. Postage The part has been carefully packed and boxed, ready for despatch by recorded post. Worldwide delivery is available: the price shown applies to Europe only, and delivery further afield may attract a supplement. Enquire before purchase for further details. All items are promptly despatched, and carefully packed using a minimum of plastic packaging. See how we package parts-->

Beocenter 9300 8001708 UK delivery and 30-day returns included • worldwide delivery available • before and after sales enquiries: 07753 241443 Beocenter 9300 upper display panel circuit boards Part numbers Modules: 44, 45, 46 Part number: 8001708, 8002740, 8002736 Supply--> Compatibility Fits all models of Beocenter 9300 only. The sole difference between the 9300 and 9500/9000 version is a pair of LEDs: the Dolby C lamp, and the cassette continuous play lamp. Condition In tested, working condition Postage The parts will be very carefully packed in ESD-safe bags, boxed, and sent by recorded post. Combined postage and international delivery is available wherever possible.

Beocenter 9500 8002740 UK delivery and 30-day returns included • worldwide delivery available • before and after sales enquiries: 07753 241443 Beocenter 9000 and 9500 Upper display panel PCBs Part numbers Modules: 44, 45, 46 Part numbers: 8002738, 8002740, 8002736 Supply--> Compatibility Compatible with type 25xx Beocenters: Beocenter 9000 Beocenter 9500 Beocenter 8000 Beocenter 8500 Untested on a Beocenter 9300, but should work despite the extra lamp positions of the earlier boards Condition In tested, working condition Postage The parts will be very carefully packed in ESD-safe bags, boxed, and sent by recorded post. Postage discounts are available wherever possible if purchasing multiple items. Combined postage and international delivery is available wherever possible.

Bang Olufsen Beogram 8002. Has some cosmetic issues as can be seen in the photos, is functional, but needs new cart/stylus. Sold as-is. Great piece for someone to clean up and lightly restore.

Bang & Olufsen Beolab 8000 / 8002 Woofer Neu Ersatz Ersatzlautsprecher Topp !!!. Sie bieten hier auf einen Woofer passend für alle Beolab 8000 Baureihen und auch fürs Nachfolgemodell 8002 ! 4 Stck sind vorhanden und können erworben werden ! absoluter Originalverpakter Neuzustand , keine Gebrauchten !!! Oder überarbeiteten original Bang &Olufsen Ersatzteile !!!

Bang and Olufsen Beolab 8002 active speakers Silver with White fretsSerial : 23… good working condition, but have some marks and stains on the white fabric .Sold without bases or brackets. One of the treads is snapped off but can still be fitted on the stand Cables will be included Shipping worldwide Info: Rob 07782307971

NEW BOXED BANG & OLUFSEN MMC2 Stylus Cartridge for B&O Beogram 6500 8002 Beocenter 2200 7007 plus these below Inspected, tested and confirmed as new condition - see imagesInterchnagable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX TX2 1800 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700MMC means Moving Micro-Cross a superior pick up technology - see belowMMC2 is the SAME spec as MMC1 with the absolute best profile (with the lowest ETM) being labelled as 1s. Get the same spec for hundreds less!ONLY 0.3 milligrammes tracking force that really protects your precious vinylSapphire tubular cantilever and line contact diamond to reduce record wear and maintain optimum surface contact providing extended and more accurate sound reproductionEffective Tip Mass of mg 0,3 B&Os best ever was just 0,25 but if you can find an MMC1 let me know too! - explanation belowBuy with confidence, over 75 new/new other condition MMC cartridge/styli sold in the last 3 years all with 100% feedbackWill fit BeoGram models: RX RX2 TX TX2 1800 2000 2404 3000 3300 3500 4500 5000 5005 5500 6002 6500 7000 8002 8500 9000 9500One MMC2 supplied Photo of all 5 MMC range is for illustration only The tubular construction offered less weight than a solid cantilever but with immense stiffness. The diamond profile was similar to that of the MMC20CL being line contact. The way to look at these cartridges was to imagine an elliptical profile but with both the front and rear facets being scooped out. In this way the vertical contact surface was maximised and the horizontal element kept to a minimum.The MMC1 and MMC2 were essentially the same cartridge with the MMC1 using the best specified diamond tips. The MMC system was carried over from the SP series but taken to an even smaller level.MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.MMC2 SpecificationsNude multi-radial Contact Line diamond, mounted on a sapphire cantilever Tracking force - grams 1 Diamond Stylus Cont. line nude Cantilever tube Sapphire Effective tip mass mg 0,3 Compliance mg/mN 30 Frequency 20-20000 Hz=/-dB 1,5 Channel separation 1000>dB 25 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 I dont like to disguise the postage and packaging costs in the item price. This shipping price includes, packing materials, insurance and first class tracking that is an unfortunate necessity due to buyer fraud. It is not even the full cost, only the Royal Mail charge. Thank you for your understanding.

NEW BOXED BANG & OLUFSEN MMC1 Stylus Cartridge for B&O Beogram 6500 8002 Beocenter 2200 7007 plus these below WHATS BETTER THAN A 30-YEAR OLD UNUSED MMC1? A PROFESSIONALLY REFURBISHED MMC1 (OBVS!) One MMC1 Cartridge supplied. Main photograph shows range available - see alternative listings for stock Inspected, tested and confirmed as better than new (old stock) condition - see imagesInterchnagable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX TX2 1800 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700MMC means Moving Micro-Cross a superior pick up technology - see belowMMC2 is the SAME spec as MMC1 with the absolute best profile (with the lowest ETM) being labelled as 1s. Get the same spec for hundreds less!ONLY 0.3 milligrammes tracking force that really protects your precious vinylSapphire tubular cantilever and line contact diamond to reduce record wear and maintain optimum surface contact providing extended and more accurate sound reproductionEffective Tip Mass of mg 0,3 B&Os best ever was just 0,25 but if you can find an MMC1 let me know too! - explanation belowBuy with confidence, over 75 new/new other condition MMC cartridge/styli sold in the last 3 years all with 100% feedbackWill fit BeoGram models: RX RX2 TX TX2 1800 2000 2404 3000 3300 3500 4500 5000 5005 5500 6002 6500 7000 8002 8500 9000 9500One MMC1 supplied Photo of all 5 MMC range is for illustration onlyMMC1 Manufactured: 1984 - 1996 Designer: Jacob Jensen Colours: Silver and Black The MMC1 was the top of the range of B&Os new cartridge range. It was only available as an upgrade - even the top of the range Beogram 8002 was only fitted with the MMC2 The MMC1 had a line contact diamond mounted on a tubular sapphire cantilever. The tubular construction offered less weight than a solid cantilever but with immense stiffness. The diamond profile was similar to that of the MMC20CL being line contact. The way to look at these cartridges was to imagine an elliptical profile but with both the front and rear facets being scooped out. In this way the vertical contact surface was maximised and the horizontal element kept to a minimum.The MMC1 and MMC2 were essentially the same cartridge with the MMC1 using the best specified diamond tips. The MMC system was carried over from the SP series but taken to an even smaller level.MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. MMC1 Product Specifications DescriptionNude multi-radial Contact Line diamond, mounted on a sapphire cantilever Tracking force - grams1 Diamond Stylus Cont. line nude Cantilever tubeSapphireEffective tip mass mg0,25 Compliance mg/mN 30 Frequency 20-20000 Hz=/-dB1 Channel separation 1000>dB30 Output mV/cm/s RMS0,6 Cartridge weight gram1,6 I dont like to disguise the postage and packaging costs in the item price. This shipping price includes, packing materials, insurance and first class tracking that is an unfortunate necessity due to buyer fraud. It is not even the full cost, only the Royal Mail charge. Thank you for your understanding.

Bang Olufsen MMC1 Stylus Cartridge Retipped Refurbished Beogram 6500 8002 7000. PROFESSIONALLY REFURBISHED using a sapphire cantilever and contact line diamond, SECURITY MARKED, TESTED AND PHOTOGRAPHED. Tested on a Beogram 6500, 2000 and a Beocenter 2200 & 7007. Not a Soundsmith copy but the real deal. Interchangeable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX2 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700. Display stand not included NEW BOXED BANG & OLUFSEN MMC1 Stylus Cartridge for B&O Beogram 6500 8002 Beocenter 2200 7007 plus these below WHATS BETTER THAN A 30-YEAR OLD UNUSED MMC1? A PROFESSIONALLY REFURBISHED MMC1 (OBVS!) Inspected, tested and confirmed as better than new (old stock) condition - see imagesInterchnagable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX TX2 1800 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700MMC means Moving Micro-Cross a superior pick up technology - see belowMMC2 is the SAME spec as MMC1 with the absolute best profile (with the lowest ETM) being labelled as 1s. Get the same spec for hundreds less!ONLY 0.3 milligrammes tracking force that really protects your precious vinylSapphire tubular cantilever and line contact diamond to reduce record wear and maintain optimum surface contact providing extended and more accurate sound reproductionEffective Tip Mass of mg 0,3 B&Os best ever was just 0,25 but if you can find an MMC1 let me know too! - explanation belowBuy with confidence, over 75 new/new other condition MMC cartridge/styli sold in the last 3 years all with 100% feedbackWill fit BeoGram models: RX RX2 TX TX2 1800 2000 2404 3000 3300 3500 4500 5000 5005 5500 6002 6500 7000 8002 8500 9000 9500One MMC1 supplied Photo of all 5 MMC range is for illustration onlyMMC1 Manufactured: 1984 - 1996 Designer: Jacob Jensen Colours: Silver and Black The MMC1 was the top of the range of B&Os new cartridge range. It was only available as an upgrade - even the top of the range Beogram 8002 was only fitted with the MMC2 The MMC1 had a line contact diamond mounted on a tubular sapphire cantilever. The tubular construction offered less weight than a solid cantilever but with immense stiffness. The diamond profile was similar to that of the MMC20CL being line contact. The way to look at these cartridges was to imagine an elliptical profile but with both the front and rear facets being scooped out. In this way the vertical contact surface was maximised and the horizontal element kept to a minimum.The MMC1 and MMC2 were essentially the same cartridge with the MMC1 using the best specified diamond tips. The MMC system was carried over from the SP series but taken to an even smaller level.MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. MMC1 Product Specifications DescriptionNude multi-radial Contact Line diamond, mounted on a sapphire cantilever Tracking force - grams1 Diamond Stylus Cont. line nude Cantilever tubeSapphireEffective tip mass mg0,25 Compliance mg/mN 30 Frequency 20-20000 Hz=/-dB1 Channel separation 1000>dB30 Output mV/cm/s RMS0,6 Cartridge weight gram1,6

Bang & Olufsen Beolab 8000 / 8002 Woofer Neu Ersatz Ersatzlautsprecher Topp !!!. Sie bieten hier auf einen Woofer passend für alle Beolab 8000 Baureihen und auch fürs Nachfolgemodell 8002 ! 4 Stck sind vorhanden und können erworben werden ! absoluter Originalverpakter Neuzustand , keine Gebrauchten !!! Oder überarbeiteten original Bang &Olufsen Ersatzteile !!!

Original Bang & Olufsen MMC2 Cartridge/StylusNewly refurbished Bang & Olufsen MMC2.Refurbished suspension with an original Bang & Olufsen nude multi-radial contact line diamond mounted on a sapphire tube cantilever.Tracking perfectly with 1gram vertical tracking forceMMC2 Specifications :Nude multi-radial Contact Line diamond mounted on a sapphire cantileverTracking force 1 gramNude Contact Line diamond stylusCantilever tube - sapphire Effective tip mass 0.3 mgCompliance mg/mN 30Frequency 20-20000 Hz=/-dB 1.5Channel separation 1000>dB 25Output mV/cm/s RMS 0.6Cartridge weight 1.6 grams Courtesy of Beoworld.orgMMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. Any questions just get in touch, Id be glad to help.

Original Bang & Olufsen MMC4 Cartridge/Stylus Uk stock ready for dispatch NOW Sounds great Checked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specification Tracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantileverTracking force - grams 1.2Diamond Stylus EllipticalCantilever tube. Tap. alum. .Effective tip mass mg 0,4Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2,5Channel separation 1000>dB 22Output mV/cm/s RMS 0,6Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources. No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC4 Cartridge/Stylus Uk stock ready for dispatch NOW Sounds great Checked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specification Tracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantileverTracking force - grams 1.2Diamond Stylus EllipticalCantilever tube. Tap. alum. .Effective tip mass mg 0,4Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2,5Channel separation 1000>dB 22Output mV/cm/s RMS 0,6Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources. No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC3 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.2gram vertical tracking force MMC3 Product SpecificationsDescription Nude elliptical diamond mounted on a tapered aluminium cantilever Tracking force - grams 1.2Diamond Stylus Elliptical nudeCantilever tube Tap. alum. .Effective tip mass mg 0,35Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2Channel separation 1000>dB 25Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Bang & Olufsen Beolab 8000 / 8002 Woofer Neu Ersatz Ersatzlautsprecher Topp !!!. Sie bieten hier auf einen Woofer passend für alle Beolab 8000 Baureihen und auch fürs Nachfolgemodell 8002 ! 4 Stck sind vorhanden und können erworben werden ! absoluter Originalverpakter Neuzustand , keine Gebrauchten !!! Oder überarbeiteten original Bang &Olufsen Ersatzteile !!!

Used Bang & Olufsen Beolab 7-4 Tweeter - 8480027.