NEW BOXED BANG & OLUFSEN MMC2 Stylus Cartridge for B&O Beogram 6500 8002 Beocenter 2200 7007 plus these below Inspected, tested and confirmed as new condition - see imagesInterchnagable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX TX2 1800 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700MMC means Moving Micro-Cross a superior pick up technology - see belowMMC2 is the SAME spec as MMC1 with the absolute best profile (with the lowest ETM) being labelled as 1s. Get the same spec for hundreds less!ONLY 0.3 milligrammes tracking force that really protects your precious vinylSapphire tubular cantilever and line contact diamond to reduce record wear and maintain optimum surface contact providing extended and more accurate sound reproductionEffective Tip Mass of mg 0,3 B&Os best ever was just 0,25 but if you can find an MMC1 let me know too! - explanation belowBuy with confidence, over 75 new/new other condition MMC cartridge/styli sold in the last 3 years all with 100% feedbackWill fit BeoGram models: RX RX2 TX TX2 1800 2000 2404 3000 3300 3500 4500 5000 5005 5500 6002 6500 7000 8002 8500 9000 9500One MMC2 supplied Photo of all 5 MMC range is for illustration onlyThe tubular construction offered less weight than a solid cantilever but with immense stiffness. The diamond profile was similar to that of the MMC20CL being line contact. The way to look at these cartridges was to imagine an elliptical profile but with both the front and rear facets being scooped out. In this way the vertical contact surface was maximised and the horizontal element kept to a minimum.The MMC1 and MMC2 were essentially the same cartridge with the MMC1 using the best specified diamond tips. The MMC system was carried over from the SP series but taken to an even smaller level.MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.MMC2 SpecificationsNude multi-radial Contact Line diamond, mounted on a sapphire cantilever Tracking force - grams 1 Diamond Stylus Cont. line nude Cantilever tube Sapphire Effective tip mass mg 0,3 Compliance mg/mN 30 Frequency 20-20000 Hz=/-dB 1,5 Channel separation 1000>dB 25 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6

NEW BOXED BANG & OLUFSEN MMC2 Stylus Cartridge for B&O Beogram 6500 8002 Beocenter 2200 7007 plus these below Inspected, tested and confirmed as new condition - see imagesInterchnagable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX TX2 1800 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700MMC means Moving Micro-Cross a superior pick up technology - see belowMMC2 is the SAME spec as MMC1 with the absolute best profile (with the lowest ETM) being labelled as 1s. Get the same spec for hundreds less!ONLY 0.3 milligrammes tracking force that really protects your precious vinylSapphire tubular cantilever and line contact diamond to reduce record wear and maintain optimum surface contact providing extended and more accurate sound reproductionEffective Tip Mass of mg 0,3 B&Os best ever was just 0,25 but if you can find an MMC1 let me know too! - explanation belowBuy with confidence, over 75 new/new other condition MMC cartridge/styli sold in the last 3 years all with 100% feedbackWill fit BeoGram models: RX RX2 TX TX2 1800 2000 2404 3000 3300 3500 4500 5000 5005 5500 6002 6500 7000 8002 8500 9000 9500One MMC2 supplied Photo of all 5 MMC range is for illustration only The tubular construction offered less weight than a solid cantilever but with immense stiffness. The diamond profile was similar to that of the MMC20CL being line contact. The way to look at these cartridges was to imagine an elliptical profile but with both the front and rear facets being scooped out. In this way the vertical contact surface was maximised and the horizontal element kept to a minimum.The MMC1 and MMC2 were essentially the same cartridge with the MMC1 using the best specified diamond tips. The MMC system was carried over from the SP series but taken to an even smaller level.MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.MMC2 SpecificationsNude multi-radial Contact Line diamond, mounted on a sapphire cantilever Tracking force - grams 1 Diamond Stylus Cont. line nude Cantilever tube Sapphire Effective tip mass mg 0,3 Compliance mg/mN 30 Frequency 20-20000 Hz=/-dB 1,5 Channel separation 1000>dB 25 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 I dont like to disguise the postage and packaging costs in the item price. This shipping price includes, packing materials, insurance and first class tracking that is an unfortunate necessity due to buyer fraud. It is not even the full cost, only the Royal Mail charge. Thank you for your understanding.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

NEW BOXED BANG & OLUFSEN MMC2 Stylus Cartridge for B&O Beogram 6500 8002 Beocenter 2200 7007 plus these below Inspected, tested and confirmed as new condition - see imagesInterchnagable with any deck that has used an MMC 1 - 5 cartridge. Eg. Beogram RX RX2 TX TX2 1800 2000 3000 3300 3500 4500 5000 5500 5005 6500 7000 8002 9000 9500 and Beocenter 2200 7007 7700MMC means Moving Micro-Cross a superior pick up technology - see belowMMC2 is the SAME spec as MMC1 with the absolute best profile (with the lowest ETM) being labelled as 1s. Get the same spec for hundreds less!ONLY 0.3 milligrammes tracking force that really protects your precious vinylSapphire tubular cantilever and line contact diamond to reduce record wear and maintain optimum surface contact providing extended and more accurate sound reproductionEffective Tip Mass of mg 0,3 B&Os best ever was just 0,25 but if you can find an MMC1 let me know too! - explanation belowBuy with confidence, over 75 new/new other condition MMC cartridge/styli sold in the last 3 years all with 100% feedbackWill fit BeoGram models: RX RX2 TX TX2 1800 2000 2404 3000 3300 3500 4500 5000 5005 5500 6002 6500 7000 8002 8500 9000 9500One MMC2 supplied Photo of all 5 MMC range is for illustration only The tubular construction offered less weight than a solid cantilever but with immense stiffness. The diamond profile was similar to that of the MMC20CL being line contact. The way to look at these cartridges was to imagine an elliptical profile but with both the front and rear facets being scooped out. In this way the vertical contact surface was maximised and the horizontal element kept to a minimum.The MMC1 and MMC2 were essentially the same cartridge with the MMC1 using the best specified diamond tips. The MMC system was carried over from the SP series but taken to an even smaller level.MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal.Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.MMC2 SpecificationsNude multi-radial Contact Line diamond, mounted on a sapphire cantilever Tracking force - grams 1 Diamond Stylus Cont. line nude Cantilever tube Sapphire Effective tip mass mg 0,3 Compliance mg/mN 30 Frequency 20-20000 Hz=/-dB 1,5 Channel separation 1000>dB 25 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 I dont like to disguise the postage and packaging costs in the item price. This shipping price includes, packing materials, insurance and first class tracking that is an unfortunate necessity due to buyer fraud. It is not even the full cost, only the Royal Mail charge. Thank you for your understanding.