GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

Up for sale is a speed/flutter, azimuth calibration cassette for cassette recorders and players. For the speed adjustment a signal of 3khz at 0db has been recorded on the side A of cassette. You will need a multimeter with frequency counter option hooked up to line out of your deck or your phone with a frequency counter app. Just adjust the speed adjustment pot to set the frequency as close to 3000 Hz as possible. For the azimuth adjustment a signal of 10khz at -10db has been recorder on the side B of cassette. You will need a multimeter hooked up to line out and adjust the azimuth screw measuring the maximum ac voltage you can get. I used my late serial number Nakamichi Dragon to record the 3 Khz test tone as the tape speed is factory adjusted and fixed and the W&F of the deck is close to 0.015%, maybe the lowest you can get from a cassette deck. To record the 10khz test tone I calibrated the playback head of my BX-300 deck using a new sealed BASF IEC/DIN standard calibration tape (picture n.4) and my oscilloscope, and each test tape I record, I use the oscilloscope to calibrate the record head as much accurate as possible, just to prevent any cassette shell imperfections. I use only NEW TDK D-30 or Maxell C-30 cassettes. This cassette is not an original test tape, but you can get pretty accurate results adjusting your deck using it. Check my feedback for this item. I moved recently in US from Greece, where I was working in Greek Nakamichi service during 90s and I have all the professional equipment (original test tapes, oscilloscope, wow & flutter meter, distortion meter, frequency response meter). If you need to service your deck Ill be happy to help you. See also my other items and my feedback. Thank you for looking.

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

Up for sale is a speed/flutter, azimuth calibration cassette for cassette recorders and players. For the speed adjustment a signal of 3khz at 0db has been recorded on the side A of cassette. You will need a multimeter with frequency counter option hooked up to line out of your deck or your phone with a frequency counter app. Just adjust the speed adjustment pot to set the frequency as close to 3000 Hz as possible. For the azimuth adjustment a signal of 10khz at -10db has been recorder on the side B of cassette. You will need a multimeter hooked up to line out and adjust the azimuth screw measuring the maximum ac voltage you can get. I used my late serial number Nakamichi Dragon to record the 3 Khz test tone as the tape speed is factory adjusted and fixed and the W&F of the deck is close to 0.015%, maybe the lowest you can get from a cassette deck. To record the 10khz test tone I calibrated the playback head of my BX-300 deck using a new sealed BASF IEC/DIN standard calibration tape (picture n.4) and my oscilloscope, and each test tape I record, I use the oscilloscope to calibrate the record head as much accurate as possible, just to prevent any cassette shell imperfections. I use only NEW TDK D-30 or Maxell C-30 cassettes. This cassette is not an original test tape, but you can get pretty accurate results adjusting your deck using it. Check my feedback for this item. I moved recently in US from Greece, where I was working in Greek Nakamichi service during 90s and I have all the professional equipment (original test tapes, oscilloscope, wow & flutter meter, distortion meter, frequency response meter). If you need to service your deck Ill be happy to help you. See also my other items and my feedback. Thank you for looking.

This is a special chrome tape Maxell XL II 90. It is a used tape. This is a tape deck speed and azimuth calibration setup cassette with lots of extra tones. (tape deck not included) Maxell chrome XL II 90 Cassette with lots of useful test tones recorded on it. The cassettes have all been recorded on my nakamichi ZX7 tape deck that has been fully serviced and calibrated (January 2023) using a professional set up. Nakamichi used to produced all their own calibration cassettes on ZX machines due to having full manual adjustment control of the azimuth and bias settings. Most machine do not have this option so will not be able to produce as accurate recording due to imperfections of tape travel. I am able to ensure the perfect azimuth alignment and bias levels for each individual cassette recorded. I also used computer software to give a very accurate level. The cassettes are also double checked with a sony quartz locked tape deck. So the tones speeds are very accurate measuring lower than 0.04 wow and flutter. I have been selling these tapes for over 3 years now with hundreds of happy customers. Please see my feedback. The tones on the tape are 3000Hz and 3150Hz for speed and wow and flutter tests.And lots of other tone for setting up tape deck levels. I have also included some useful channel identification test tracks, white noise and other useful test tracks. Each track has a description before the tone to help find the tone you want. Track listing. 3000 Hz tone (0dB)3150Hz (0dB)400Hz (0dB)500Hz (0dB)1000Hz (0dB)10,000Hz (-10dB)12,000Hz (-10dB)15,000Hz (-10dB)19,500Hz (-10dB)Frequency Sweep 20Hz - 20000Hz 400Hz (0dB) @250n Wb/m (5.00)Channel IdentificationWhite Noise (0dB) If you need any other tones please ask as I can add them to the tape.But there will be a small extra charge due to time to set everything up. To use the tape down load a frequency counter app for your phone. Play the tape and check the frequency on the app. If needed adjust the speed of your tape decks motor. This will be on the back of the motor or a pot on the circuit board.

This is a special chrome tape Maxell XL II 90. It is a used tape. This is a tape deck speed and azimuth calibration setup cassette with lots of extra tones. (tape deck not included) Maxell chrome XL II 90 Cassette with lots of useful test tones recorded on it. The cassettes have all been recorded on my nakamichi ZX7 tape deck that has been fully serviced and calibrated (January 2023) using a professional set up. Nakamichi used to produced all their own calibration cassettes on ZX machines due to having full manual adjustment control of the azimuth and bias settings. Most machine do not have this option so will not be able to produce as accurate recording due to imperfections of tape travel. I am able to ensure the perfect azimuth alignment and bias levels for each individual cassette recorded. I also used computer software to give a very accurate level. The cassettes are also double checked with a sony quartz locked tape deck. So the tones speeds are very accurate measuring lower than 0.04 wow and flutter. I have been selling these tapes for over 3 years now with hundreds of happy customers. Please see my feedback. The tones on the tape are 3000Hz and 3150Hz for speed and wow and flutter tests.And lots of other tone for setting up tape deck levels. I have also included some useful channel identification test tracks, white noise and other useful test tracks. Each track has a description before the tone to help find the tone you want. Track listing. 3000 Hz tone (0dB)3150Hz (0dB)400Hz (0dB)500Hz (0dB)1000Hz (0dB)10,000Hz (-10dB)12,000Hz (-10dB)15,000Hz (-10dB)19,500Hz (-10dB)Frequency Sweep 20Hz - 20000Hz 400Hz (0dB) @250n Wb/m (5.00)Channel IdentificationWhite Noise (0dB) If you need any other tones please ask as I can add them to the tape.But there will be a small extra charge due to time to set everything up. To use the tape down load a frequency counter app for your phone. Play the tape and check the frequency on the app. If needed adjust the speed of your tape decks motor. This will be on the back of the motor or a pot on the circuit board.

Up for sale is a speed/flutter, azimuth calibration cassette for cassette recorders and players. For the speed adjustment a signal of 3khz at 0db has been recorded on the side A of cassette. You will need a multimeter with frequency counter option hooked up to line out of your deck or your phone with a frequency counter app. Just adjust the speed adjustment pot to set the frequency as close to 3000 Hz as possible. For the azimuth adjustment a signal of 10khz at -10db has been recorder on the side B of cassette. You will need a multimeter hooked up to line out and adjust the azimuth screw measuring the maximum ac voltage you can get. I used my late serial number Nakamichi Dragon to record the 3 Khz test tone as the tape speed is factory adjusted and fixed and the W&F of the deck is close to 0.015%, maybe the lowest you can get from a cassette deck. To record the 10khz test tone I calibrated the playback head of my BX-300 deck using a new sealed BASF IEC/DIN standard calibration tape (picture n.4) and my oscilloscope, and each test tape I record, I use the oscilloscope to calibrate the record head as much accurate as possible, just to prevent any cassette shell imperfections. I use only NEW TDK D-30 or Maxell C-30 cassettes. This cassette is not an original test tape, but you can get pretty accurate results adjusting your deck using it. Check my feedback for this item. I moved recently in US from Greece, where I was working in Greek Nakamichi service during 90s and I have all the professional equipment (original test tapes, oscilloscope, wow & flutter meter, distortion meter, frequency response meter). If you need to service your deck Ill be happy to help you. See also my other items and my feedback. Thank you for looking.

Up for sale is a speed/flutter, azimuth calibration cassette for cassette recorders and players. For the speed adjustment a signal of 3khz at 0db has been recorded on the side A of cassette. You will need a multimeter with frequency counter option hooked up to line out of your deck or your phone with a frequency counter app. Just adjust the speed adjustment pot to set the frequency as close to 3000 Hz as possible. For the azimuth adjustment a signal of 10khz at -10db has been recorder on the side B of cassette. You will need a multimeter hooked up to line out and adjust the azimuth screw measuring the maximum ac voltage you can get. I used my late serial number Nakamichi Dragon to record the 3 Khz test tone as the tape speed is factory adjusted and fixed and the W&F of the deck is close to 0.015%, maybe the lowest you can get from a cassette deck. To record the 10khz test tone I calibrated the playback head of my BX-300 deck using a new sealed BASF IEC/DIN standard calibration tape (picture n.4) and my oscilloscope, and each test tape I record, I use the oscilloscope to calibrate the record head as much accurate as possible, just to prevent any cassette shell imperfections. I use only NEW TDK D-30 or Maxell C-30 cassettes. This cassette is not an original test tape, but you can get pretty accurate results adjusting your deck using it. Check my feedback for this item. I moved recently in US from Greece, where I was working in Greek Nakamichi service during 90s and I have all the professional equipment (original test tapes, oscilloscope, wow & flutter meter, distortion meter, frequency response meter). If you need to service your deck Ill be happy to help you. See also my other items and my feedback. Thank you for looking.

TEAC MTT-113 AZIMUTH 6,3kHz TEST TAPE Cassette Deck. Professionelle Messwerkzeuge, beantworten Sie nicht die Verwendung, bitte kaufen Sie sorgfältig! normal funktioniert??? Da es sich um einen Privatverkauf handelt, schließe ich die jegliche Gewährleistung oder Garantie aus. Ein Rückgabe- oder Widerrufsrecht existiert nicht. Zudem erfolgt der Verkauf unter Ausschluss jeglicher Sachmangelhaftung. WICHTIGER HINWEIS: wegen der neuen Gesetzesbestimmungen erfolgt der Verkauf unter Ausschluss jeglicher Gewährleistung, Garantie und Rücknahme. Da es sich um einen Privatverkauf handelt, kann ich keine Garantie nach neuem EU-Recht übernehmen. Der Käufer erklärt sich damit einverstanden und erkennt dies mit seinem Kauf an. Laut dem neuen EU-Recht muss dieser Zusatz unter jedem Online-Verkauf stehen, ansonsten haftet der Verkäufer auch als Privatperson ein Jahr für die verkaufte Ware. Bitte bieten Sie nur, wenn Sie mit dem Ausschluss der Garantie und Rücknahme einverstanden sind, da Privatverkauf. Only sold in the EU ? Private sale, no invoice provided?

Up for sale is a speed/flutter, azimuth calibration cassette for cassette recorders and players. For the speed adjustment a signal of 3khz at 0db has been recorded on the side A of cassette. You will need a multimeter with frequency counter option hooked up to line out of your deck or your phone with a frequency counter app. Just adjust the speed adjustment pot to set the frequency as close to 3000 Hz as possible. For the azimuth adjustment a signal of 10khz at -10db has been recorder on the side B of cassette. You will need a multimeter hooked up to line out and adjust the azimuth screw measuring the maximum ac voltage you can get. I used my late serial number Nakamichi Dragon to record the 3 Khz test tone as the tape speed is factory adjusted and fixed and the W&F of the deck is close to 0.015%, maybe the lowest you can get from a cassette deck. To record the 10khz test tone I calibrated the playback head of my BX-300 deck using a new sealed BASF IEC/DIN standard calibration tape (picture n.4) and my oscilloscope, and each test tape I record, I use the oscilloscope to calibrate the record head as much accurate as possible, just to prevent any cassette shell imperfections. I use only NEW TDK D-30 or Maxell C-30 cassettes. This cassette is not an original test tape, but you can get pretty accurate results adjusting your deck using it. Check my feedback for this item. I moved recently in US from Greece, where I was working in Greek Nakamichi service during 90s and I have all the professional equipment (original test tapes, oscilloscope, wow & flutter meter, distortion meter, frequency response meter). If you need to service your deck Ill be happy to help you. See also my other items and my feedback. Thank you for looking.

Thank you for looking at my shop!?Hope you have the best shopping! !??CONDITION LEVEL??New-Unused-Excellent-Very Good-Good-Acceptable-JunkCondition:Junk noteOperation cannot be confirmed (because it is not in an environment where operation can be confirmed) ????SHIPPING?????Please check your address before paying because we can ONLY ship to addresses that are entered before placing the order. We cannot change an address after the order has already been placed.?We provide valid Tracking Numbers for all orders.?All our international packages ship under the Fedex or Japan Post or DHL. ????CUSTOMER SERVICE?????If you have any questions or issues, we are at your service. You can email us anytime through eBay messages. ??RETURN INFORMATION???We offer a standard FREE 30 days refund or exchange policy. Item must be returned in original condition in order to receive a full refund. ????Customs duty?????Import duties, taxes, and charges are not included in the item price or shipping cost.These charges are the buyers responsibility.?Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.?We cant not reply gifts or unreasonable requests such as declared amount.

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

KÖNIG BFC 41 Bezugs- und Frequenzgang Testcassette für Reference Level, Azimuth Einstellung, Geschwindigkeitseinstellung, Messung des Wiedergabefrequenzgangs gebrauchter Zustand, s. Originalbilder Abholung oder Versand per versichertem Paket Gewährleistung oder Rücknahme sind ausgeschlossen.

Up for sale is a speed/flutter, azimuth calibration cassette for cassette recorders and players. For the speed adjustment a signal of 3khz at 0db has been recorded on the side A of cassette. You will need a multimeter with frequency counter option hooked up to line out of your deck or your phone with a frequency counter app. Just adjust the speed adjustment pot to set the frequency as close to 3000 Hz as possible. For the azimuth adjustment a signal of 10khz at -10db has been recorder on the side B of cassette. You will need a multimeter hooked up to line out and adjust the azimuth screw measuring the maximum ac voltage you can get. I used my late serial number Nakamichi Dragon to record the 3 Khz test tone as the tape speed is factory adjusted and fixed and the W&F of the deck is close to 0.015%, maybe the lowest you can get from a cassette deck. To record the 10khz test tone I calibrated the playback head of my BX-300 deck using a new sealed BASF IEC/DIN standard calibration tape (picture n.4) and my oscilloscope, and each test tape I record, I use the oscilloscope to calibrate the record head as much accurate as possible, just to prevent any cassette shell imperfections. I use only NEW TDK D-30 or Maxell C-30 cassettes. This cassette is not an original test tape, but you can get pretty accurate results adjusting your deck using it. Check my feedback for this item. I moved recently in US from Greece, where I was working in Greek Nakamichi service during 90s and I have all the professional equipment (original test tapes, oscilloscope, wow & flutter meter, distortion meter, frequency response meter). If you need to service your deck Ill be happy to help you. See also my other items and my feedback. Thank you for looking.

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

GennLab Azimuth Alignment Cassettes.Following options are available315 Hz, 6.3, 8, 10, 12.5, 14 or 15 kHz Azimuth Test Cassette/Tape.Please note. These cassettes are 90 degrees ANGLE cassettes. They can not be used to equalize channel outputs or as Frequency Response cassettes.Suitable for Playback Head Azimuth alignment of any Cassette Tape Deck using a dual trace oscilloscope (minimum difference in phase between channels) or an AC millivoltmeter (maximum Output Level)Only new TDK, TEAC, MAXELL, SONY, AMPEX or RTM 17u tape is used when recording. Azimuth cassettes are recorded IN SHELL using a tape recorder with Record head azimuth control during recording.Time Constant: 3180us + 70usRecord Level: 20dB below 200nWb/m @ 400Hz. To order a cassette with different Record Level go to the TEAC Calibration Cassettes or SONY Calibration Cassettes page of GennLab.Frequency fluctuation: +/-0.01% measuredVertical azimutn angle: 90 degr. +/- 2 minDuration 10 min recorded in the MIDDLE of the Tape from 2 min 30 sec to 12 min 30 sec for the 1-7/8 ips tape.Please specify cassette Frequency from the following options:315 Hz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 14 kHz, 15 kHz, andcassette Speed from the following options:15/16 ips (2.38125 cm/sec), 1-7/8 ips (4.7625 cm/sec), 3-3/4 ips (9.525 cm/sec), 7-1/2 ips (19.05 cm/sec), 15 ips (38.1 cm/sec).

Toothed Azimuth Belt for Tandberg TCD 3014 Cassette Deck. May also fit other models. Shipping is $4 to the continental US; all others use eBays Global Shipping Program. Sorry, no shipping to Alaska, Hawaii or Puerto Rico.