Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Biete ein hochwertiges Audax Car Hifi 2- Wege Set Tieftöner HT170 Z0 / Hochtöner Audax TW 010 A1 an. Optisch und technisch einwandfrei. Die Chassis wurden nicht verbaut und sind noch Neu. Das Tieftönermaß ist ein Standard 16,5cm, das in viele Originalauschnitte der diversen KFZ passt. WICHTIG! Aufgrund des neuen EU-Rechts gelten folgende Bedingungen: Bei dieser Auktion handelt es sich um einen Kaufvertrag von Privat an Privat nach § 13 BGB. Die Auktion erfolgt unter Ausschluss jeglicher Gewährleistung, Garantie und Rücknahme. Gemäß § 447 BGB gilt, dass mit Übergabe an den Versand die Gefahr auf den Käufer übergeht.

Biete ein hochwertiges Audax Car Hifi 2- Wege Set Tieftöner HT170 Z0 / Hochtöner Audax TW 010 A1 an. Optisch und technisch einwandfrei. Das Chassis wurde nicht verbaut und sind noch Neu. Als Zubehör lege ich noch hochwertige Frequenzweichenbauteile 2x 1,2mH Luftspule und 2x MKT Kondensatoren 4,7µF bei. Das Tieftönermaß ist ein Standard 16,5cm, das in viele Originalauschnitte der diversen KFZ passt. WICHTIG! Aufgrund des neuen EU-Rechts gelten folgende Bedingungen: Bei dieser Auktion handelt es sich um einen Kaufvertrag von Privat an Privat nach § 13 BGB. Die Auktion erfolgt unter Ausschluss jeglicher Gewährleistung, Garantie und Rücknahme. Gemäß § 447 BGB gilt, dass mit Übergabe an den Versand die Gefahr auf den Käufer übergeht.

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Verkaufe ein paar AUDAX Mitteltner mit Super Klang. Die Lautsprecher funktionieren einwandfrei. AUDAX PR170M0 Weltweit anerkannter professioneller 17 cm Mitteltnermit exzellenter Papier-Membrane! Sehr hoher Schalldruck von 99 dB SPL und resonanzfreier bertragunsbereich bis zu 6 kHz! Baugleicher Ersatz fr ltereMHD17HR37 RSM/TSM, PR17HR37, PR17HR60/70/100 usw.. Wird u.a. von EAW, EV, Nexo, Westlake und ZECK eingesetzt. Massiver Gusskorb KAPTON-Schwingspulentrger mit Fiberglass verstrkt! 40 mm ALU-Flachdrahtspule verkupfert Vergoldete Terminals SPL 99 dB Oft kopiert - NIE erreicht !! Technische Daten Nominale Impedanz :8 Ohm Empf. Frequenzbereich :500-6.000 Hz Empf. Gehuseprinzip :Closed 3-6 l SPL 2,83 V/1m :99 dB Fs :125 Hz Qts :0,40 Qes :0,47 Qms :2,70 Vas :6,5 Liter Xmax :0,5 +- mm Rdc :6,2 Ohm Gewicht :2,7 Kg

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

For sale are a pair of used Audax HM170C0 carbon fiber woofers in excellent condition. These are briefly used spares. New models of the same speaker run about $120 each. I am selling them only because I am downsizing.Shipping price is for continental U.S. only.

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber

Top of the line AUDAX HM170Z0 Woofer, 6.5s, 8 Ohms, quality made and designed in France, Cast Frame, excellent quality and performance. Open Box, New, Always inside climate controlled non smoking environment, Top Line, Ex Quality, France. The shipping cost includes safe packing, insurance, prompt shipping and tracking number. Buy with confidence, see my feedback. Good listening, SonnY :) See the impressive specs and description below HD-A represents a true breakthrought in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combination of newly developed materials and processes. Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone ise based on a totally controlled matric of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the contour and weight of the cone, while making it possible to vary the thickness of the membrane along the profile. This 6 1/2 bass-midrange driver was developped for top range, no-compromise high end 2 or 3-way systems. It features a die cast Zamack chassis with unobstructed venting for enhanced transient response and a non resonant phase plug for high and frequency equalization. High power handling results from the flat, edgewound copper coil mounted onto a fiberglass reinforced Kpaton voice coil former. Unequaled definition is achieved over a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise and detailed imaging. General Product type Cone driver Brand Audax Reference HM170Z0 Product code 100996Y Informations Nominal impedance 8 ohm Dimensional category 6.5 inch, 7.5 inch Frequency coverage type Sub, Low Manufacturer sensitivity 91 dB Calculated sensitivity 90.24 dB Nominal power handling 60 W Fundamental parameters Sd 138 cm² Mms 9.9 gr Le 0.34 mH Re 6.2 ohm BL 6 T.m Small signal parameters Fs 40 Hz Qes 0.42 Qms 6.15 Qts 0.4 Vas 45.3 L Datas Xmax ±3.75 mm Calculated Xmax ±5.4167 mm EBP 95 Hz Zmin 7.4 ohm Fs / Qts 100 Hz Vas * Qts² 7.25 L Calculated efficiency 0.67 % Dimensions Voice coil diameter 1.18 inch Winding depth 12.5 mm Gap height 5 mm External dimensions 166 | 188 mm Baffle cutout diameter 145 mm Front thickness 7.2 mm Depth after front 70 mm Diamètre aimant (mm) 86.1 mm Shape & Materials Front chape Cylindrical Magnet type Ferrite Basket masterial Zamak Winding material Copper Voice coil former Kapton Surround material Rubber