ANTHEM MCA 20 MCA20 MCA-20 2 Channel Amplifier NICE! L@@K !! Used, Tested, and Working. Very nice condition amplifier. Minor flaws/Blemishes. SEE PICTURES!! General Inputs 2 Single-Ended, 2 Balanced, 1 Relay Trigger (3.5-mm Mono Jack) Outputs 2 Pairs Speaker Binding Posts, 1 Relay Trigger (3.5-mm Mono Jack) SWITCHES Front Panel Power (On/Off) Rear Panel 3 On/Off Modes (Trigger, Manual, Auto) POWER OUTPUT (Continuous RMS, 20 Hz - 20 kHz, <1.0% THD) Impedance 8? 4? 2? # of Channels Driven 1 All 1 All 1 All 225 W 200 W 370 W 300 W 535 W 410 W OTHER SPECIFICATIONS HEADROOM 1.45 db (8 ?); 2.3 db (4 ?) POWER BANDWIDTH 10 Hz - 80 kHz (200 W @ 8 ?) FREQUENCY RESPONSE 20 Hz - 20 kHz (-0.15 db); 5 Hz - 100 kHz (-2 db) THD + N 0.0015% @ 1 kHz; 0.03% @ 20 kHz (100 W into 8 ?) INPUT SENSITIVITY 1.5 VRMS for 225 W into 8 ? INPUT IMPEDANCE 10 k ? (RCA); 15 k ? (XLR) DAMPING FACTOR 130 @ 1 kHz (ref. 8 ?) S/N RATIO 122 db, A-weighted (ref. 225 W) CHANNEL SEPARATION >65 db (100 Hz - 10 kHz) VOLTAGE GAIN 29 db SLEW RATE 20 v/µs POWER REQUIREMENTS 800 W @ maximum power output (8 ? load) DIMENSIONS (H x W x D; heights include feet) 17-1/4 (43.8 cm) Wide x 7 (17.8 cm) High x 12-1/4 (31 cm) Deep WEIGHT (Unpacked) 35 lb (15.9 kg) Rack-mounting: 4 rack units, without feet

Anthem AVM 50 7.2 channel A/V processor (no internal amplification). THX Ultra2, THX Surround EX, DTS ES Neo:6, Dolby Digital EX, and many other modes supported. 2 zones. The AVM 50 has state of the art video processing which includes deinterlacing, scaling, aspect ratio control, and picture adjustment. Anthem products are engineered to recreate the passion of live performance and thrill of the best movie theaters by using the highest level of circuit design, proprietary software, superior build quality, innovative features, and intuitive ergonomics with tremendous flexibility. Video inputs/outputs: HDMI: 4 inputs, 1 outputComponent: 2 inputs, 2 outputsS-Video: 7 inputs, 5 outputsComposite: 7 inputs, 5 outputs Audio inputs/outputs: Pre-amp: 7.2 outputs (XLR and RCA)Digital (coaxial) audio: 7 inputs, 2 outputsOptical audio: 3 inputsAnalog audio: 7 inputs, 4 outputs Heres whats included: Operating Manual - great condition, handled carefully - no writing, bends, or tearsRemote control - some minor wear where its been held - backlit and works wellAntenna - not sure if its AM or FM - never usedPower cableOriginal box The processor is in superb condition with very little signs of wear. It was primarily used on the weekends to watch movies with my family, and it still works well. Im selling it to upgrade to the newer Anthem AVM 70. Looking for other quality home theater components? You can search for my Sony VPL-VW50 projector and Roku Ultra 4660x2 which Im also selling. Let me know if youre interested in multiple items, and Ill do my best to consolidate shipping (where possible).

For Sale Anthem MCA 225 Gen2 Power Amplifier. 225W/ch @ 8 ohms, 400W/ch @ 4 ohms, 600Wch @ 2 ohms. Amazing clean sound - very neutral sounding amp. Powerful lows and very detailed highs. Just check out the reviews, You cant go wrong with this amp. I am pairing down my system so it has to go. Ships with a 2M AudioQuest NRG10 power cord w/72+DBS.

For sale is a barely used Anthem MCA 225 generation 2 stereo amplifier that is in near mint condition. Bought more amps than I needed. This is a high-quality amplifier with excellent power specs and great sound. This is the newest, generation 2, version of this amplifier. Works as a stereo piece or as part of a multichannel system. Has both RCA and balanced inputs. There is some surface dust and some smudges in the photos, but these all wipe off. The top metal is clean, but it does have a few surface marks, typical for the matte pebbly surface coating used on the top of this product. US only sales. I will ship via insured FEDEX.Specs:225 watts per channel into 8 ohms (20-20,000 Hz) at 0.015% THD with 2 channels driven400 watts per channel into 4 ohms600 watts per channel into 2 ohmsClass AB design with 8 high-current bipolar output transistors per channel for lower distortionlow-noise, high-power toroidal transformer for stable, noise-free performancehigh-quality filter capacitors and advanced power supply regulatorsAdvanced Load Monitoring™ technology monitors internal temperature, current, and voltage to ensure safe, uninterrupted operation3-way on/off operation: manual, triggered, or signal-sensing auto on/offstereo balanced XLR and unbalanced RCA inputscustom-designed binding post terminals accept bare wire, banana plugs, and spade lugs3.5mm trigger in/out jacks allow the amplifier to be turned on or off remotelysignal-to-noise ratio: 120 dBdesigned, engineered, and manufactured in Canadadetachable power cordDimensions:17-1/4W x 6-5/8H x 18-1/8Dweight: 40 lbs.

The Anthem Statement A2 audiophile amplifier is a top-of-the-line device designed to provide high-quality sound output for your best speakers. With its powerful 2x 200watts amplifier you can expect great performance. Some minor scratches on top. Please see pictures. Don’t waste your time with newer cheaper options pushed by paid YouTubers. Hook up a streamer and enjoy the beautiful sound that come from these statement line amp. This amplifier is perfect for music enthusiasts who demand high-quality audio output. The Anthem Statement A2 model is built to last and offers a sleek and modern design that will complement any home decor. Whether you're watching movies or listening to your favorite albums, this amplifier is sure to impress. Note: Only shipping to continental USA. Also can deliver locally in a 30 mile radius from my house in Wellington Florida.

Anthem AVR50. Unit powers on but the volume control spins freely with no change. Selling for parts.

For sale: Make: Anthem Model: Statement A2 Power Amp. Great cosmetic & working order. Light signs, of use, and wear. Comes with the original manual & power cord, but the manual does have writing on it as seen in the photos. NYS residents to pay sales tax. Sold AS-IS. Shipping rates are for the continental US only. Please inquire regarding shipping to all other foreign locations. Payment is preferred via Paypal, but other methods are also accepted. Please inquire about alternate payments. Thanks for looking. Thanks again. Rack-E

For sale: Make: Anthem Model: Statement A2 Power Amp. Great cosmetic & working order. Light signs, of use, and wear. Comes with the original manual & power cord, but the manual does have writing on it as seen in the photos. NYS residents to pay sales tax. Sold AS-IS. Shipping rates are for the continental US only. Please inquire regarding shipping to all other foreign locations. Payment is preferred via Paypal, but other methods are also accepted. Please inquire about alternate payments. Thanks for looking. Thanks again. Rack-E

This unit has very low hours and is flawless. It has only been used for 9 months in a dedicated audio room (pet and smoke free) since the original purchase date. I had to relocate for work and did not have the space for an audio room. I kept it in the closet hoping to one day have another audio room. I have since transitioned to in-wall speakers and don’t need the power the delivers. I have a pair available. I am also selling a flawless A5 amp. This unit was bi-amped for one of my main speakers. Multi-Talented Performers A2 amplifiers are muscular in character and musical by nature. They are multi-talented performers more than capable of supplying the power behind the sonically demanding aspects of surround-sound home theater, or recreating, with remarkable finesse and transparency, the ‘immediacy’ of a live music performance. The secret behind their award-winning performance can be found in Anthem’s unwavering commitment to state-of-the-art design. A2 amplifiers boast: completely modular construction; a four-layer circuit board topology; mirror-imaged, frequency-response channel matching; eight bipolar output devices per channel; hand-matched complementary input devices; massive toroidal power supplies; oversize convection-cooled aluminum heatsinks; and a no-fuse design strategy. Gorgeous Pieces of Industrial Design No Fuse Design A2 amplifiers are Direct-Connected to the power supply capacitor bank, keeping output impedance remarkably low while making more power available to the amplifier. Even when the amplifiers are driving lower- or complex-impedance loads, the result is audibly superior performance. If an output short circuit does occur, only the AC line breaker will trip—there are no fuses to replace. The standby low-power supply is protected by self-resetting Positive Temperature coefficient thermistors (PTCs). Once the condition that tripped the PTC disappears, the circuit restores itself automatically. Massive Oversize Power Supply Reservoirs To store all of the energy required for the immense bursts of power required in movie special effects or the taxing crescendos in music, large banks of capacitors are required. A2 amplifiers employ 16,400 micro farads (?F) of capacitance per channel. (That’s over 80,000 ?f alone in the A2!) With so many joules of power in reserve, these amplifiers are able to instantly and effortlessly deliver full, uninterrupted bursts of power. Hand-Matched Complementary Input Devices Heat shrink tubing applied around each critical pair of hand-matched complementary input devices ensures superior thermal tracking and lower voltage offset and distortion. Oversize Convection-Cooled Heatsinks/Fins Computer-designed and modeled to maximize contact area for exceptional heat transfer, these amplifiers run cooler for greater reliability without the need for a noise-inducing fan. Eight Bipolar Output Devices Per Channel Solid-state amplifiers get their power from the output devices used in the amplification stage—the greater the number of devices per channel, the greater the available high-current power for the crescendos in music or the thrills, thunder and explosions in movies. Performance is simply more effortless. It also means that the amplifiers run cooler, making them more reliable. and A2 amplifiers each have eight bipolar output devices per channel ensuring tremendous current reserves and outstanding reliability. State-of-the-Art Modular Design A2 amplifiers reflect the benefit of a common modular design enhanced by our highly refined amplifier circuit topology. Each amplifier channel is self-contained on its own board and heatsink. In the rare event that servicing is required, it can be done quickly and easily by a qualified technician, minimizing the down time of your system. Four-Layer Circuit Boards Our hand-designed four-layer military spec (FR-4-rated) glass-epoxy circuit boards with plated through-holes makes extensive use of ground planes to ensure excellent separation between amplifier channels. The result is exceptionally low noise and low crosstalk between channels, as well as between inputs. This multi-layered design also offers increased protection from electrostatic discharge. 120 dB Signal-To-Noise Ratio Transformer-induced noise at the bass frequencies of 60 Hz, 120 Hz, and 180 Hz has effectively been eliminated. As a result, and A2 amplifiers boast vanishing noise and remarkably low levels of Total Harmonic Distortion. The reproduction of subtle harmonic structures in each of these powerful amplifiers reveals extraordinary spatial ambience and soundstage dimension. Reference-Quality Input Connections Gold-plated female RCA jacks on A2 provide a high-quality input connection. True-Balanced XLR connections ensure the lowest level of noise and hum possible. Our unique auto-sensing technology means no switches. Just plug in either the RCA or XLR connector and our auto-sensing technology will automatically select the right input. Ultra-Quiet Toroidal Power Supply Thanks to massive conservatively rated toroidal power supplies designed with high rail voltages, A2 multichannel amplifiers provide ultra quiet performance. Transformers are shaped to minimize stray electromagnetic radiation and tuned to minimize hum. Designed and Built in North America Heavy-gauge 14-awg steel chassis with fine-grain brushed aluminum cover and extruded aluminum handles. Includes IEC detachable AC female sockets and high-power, high-quality 14-awg AC cords. Can be ordered with rack-mount handles. (See Dealer for more information.) Oversize Output Connections Custom-designed oversize gold-plated binding posts ensure full power delivery at all times. They’re easy to use while facilitating large speaker cable connectors. GENERALInputs2 Single-Ended, 2 Balanced, 1 Relay Trigger (3.5 mm Mono Jack)Outputs2 Pairs Speaker Binding Posts, 1 Relay Trigger (3.5 mm Mono Jack)THD+N (200 W into 8 ?)0.001% at 1 kHz, 0.03% at 20 kHzIMD0.0005% (CCIF, 225 W into 8 ?)POWER BANDWIDTH10 Hz to 100 kHz (+0 -3 dB, 225 W into 8 ?)FREQUENCY RESPONSE20 Hz to 20 kHz (+0 -0.15 dB), 5 Hz to 100 kHz (+0 -2 dB)INPUT SENSITIVITY1.5 Vrms in for 225 W out into 8 ?INPUT IMPEDANCE10 k? (RCA), 15 k? (XLR)DAMPING FACTOR360 at 1 kHz (ref. 8 ?)S/N RATIO120 dB, A-weighted (ref. 225 W)CROSSTALK-78 dB at 1 kHzVOLTAGE GAIN29 dBSLEW RATE30 V/µsSWITCHESFront PanelPower (On/Off)Rear PanelOn/Off Modes (Trigger, Manual, Auto), Inputs (RCA, XLR)POWER OUTPUT (Continuous RMS, 20 Hz to 20 kHz, <0.1% THD) Impedance 8? 4? 2? # of Channels Driven 1 All 1 All 1 All 225 W 200 W 370 W 300 W 535 W 410 W *Special Test Conditions Required for 2 ?POWER REQUIREMENTSSUPPLY VOLTAGE105 to 130 V, 60 HzPOWER CONSUMPTION800 WDIMENSIONSHeight7-5/8 inches (19.4 cm) including feetWidthFaceplate 19-1/4 inches (49 cm), Chassis 17-1/4 inches (43.8 cm)Depth13-1/2 inches (34.3 cm)Weight (unpacked)34 lb (15.5 kg)

This unit has very low hours and is flawless. It has only been used for 9 months in a dedicated audio room (pet and smoke free) since the original purchase date. I had to relocate for work and did not have the space for an audio room. I kept it in the closet hoping to one day have another audio room. I have since transitioned to in-wall speakers and don’t need the power the delivers. I have a pair available. I am also selling a flawless A5 amp. This unit was bi-amped for one of my main speakers. Multi-Talented Performers A2 amplifiers are muscular in character and musical by nature. They are multi-talented performers more than capable of supplying the power behind the sonically demanding aspects of surround-sound home theater, or recreating, with remarkable finesse and transparency, the ‘immediacy’ of a live music performance. The secret behind their award-winning performance can be found in Anthem’s unwavering commitment to state-of-the-art design. A2 amplifiers boast: completely modular construction; a four-layer circuit board topology; mirror-imaged, frequency-response channel matching; eight bipolar output devices per channel; hand-matched complementary input devices; massive toroidal power supplies; oversize convection-cooled aluminum heatsinks; and a no-fuse design strategy. Gorgeous Pieces of Industrial Design No Fuse Design A2 amplifiers are Direct-Connected to the power supply capacitor bank, keeping output impedance remarkably low while making more power available to the amplifier. Even when the amplifiers are driving lower- or complex-impedance loads, the result is audibly superior performance. If an output short circuit does occur, only the AC line breaker will trip—there are no fuses to replace. The standby low-power supply is protected by self-resetting Positive Temperature coefficient thermistors (PTCs). Once the condition that tripped the PTC disappears, the circuit restores itself automatically. Massive Oversize Power Supply Reservoirs To store all of the energy required for the immense bursts of power required in movie special effects or the taxing crescendos in music, large banks of capacitors are required. A2 amplifiers employ 16,400 micro farads (?F) of capacitance per channel. (That’s over 80,000 ?f alone in the A2!) With so many joules of power in reserve, these amplifiers are able to instantly and effortlessly deliver full, uninterrupted bursts of power. Hand-Matched Complementary Input Devices Heat shrink tubing applied around each critical pair of hand-matched complementary input devices ensures superior thermal tracking and lower voltage offset and distortion. Oversize Convection-Cooled Heatsinks/Fins Computer-designed and modeled to maximize contact area for exceptional heat transfer, these amplifiers run cooler for greater reliability without the need for a noise-inducing fan. Eight Bipolar Output Devices Per Channel Solid-state amplifiers get their power from the output devices used in the amplification stage—the greater the number of devices per channel, the greater the available high-current power for the crescendos in music or the thrills, thunder and explosions in movies. Performance is simply more effortless. It also means that the amplifiers run cooler, making them more reliable. and A2 amplifiers each have eight bipolar output devices per channel ensuring tremendous current reserves and outstanding reliability. State-of-the-Art Modular Design A2 amplifiers reflect the benefit of a common modular design enhanced by our highly refined amplifier circuit topology. Each amplifier channel is self-contained on its own board and heatsink. In the rare event that servicing is required, it can be done quickly and easily by a qualified technician, minimizing the down time of your system. Four-Layer Circuit Boards Our hand-designed four-layer military spec (FR-4-rated) glass-epoxy circuit boards with plated through-holes makes extensive use of ground planes to ensure excellent separation between amplifier channels. The result is exceptionally low noise and low crosstalk between channels, as well as between inputs. This multi-layered design also offers increased protection from electrostatic discharge. 120 dB Signal-To-Noise Ratio Transformer-induced noise at the bass frequencies of 60 Hz, 120 Hz, and 180 Hz has effectively been eliminated. As a result, and A2 amplifiers boast vanishing noise and remarkably low levels of Total Harmonic Distortion. The reproduction of subtle harmonic structures in each of these powerful amplifiers reveals extraordinary spatial ambience and soundstage dimension. Reference-Quality Input Connections Gold-plated female RCA jacks on A2 provide a high-quality input connection. True-Balanced XLR connections ensure the lowest level of noise and hum possible. Our unique auto-sensing technology means no switches. Just plug in either the RCA or XLR connector and our auto-sensing technology will automatically select the right input. Ultra-Quiet Toroidal Power Supply Thanks to massive conservatively rated toroidal power supplies designed with high rail voltages, A2 multichannel amplifiers provide ultra quiet performance. Transformers are shaped to minimize stray electromagnetic radiation and tuned to minimize hum. Designed and Built in North America Heavy-gauge 14-awg steel chassis with fine-grain brushed aluminum cover and extruded aluminum handles. Includes IEC detachable AC female sockets and high-power, high-quality 14-awg AC cords. Can be ordered with rack-mount handles. (See Dealer for more information.) Oversize Output Connections Custom-designed oversize gold-plated binding posts ensure full power delivery at all times. They’re easy to use while facilitating large speaker cable connectors. GENERALInputs2 Single-Ended, 2 Balanced, 1 Relay Trigger (3.5 mm Mono Jack)Outputs2 Pairs Speaker Binding Posts, 1 Relay Trigger (3.5 mm Mono Jack)THD+N (200 W into 8 ?)0.001% at 1 kHz, 0.03% at 20 kHzIMD0.0005% (CCIF, 225 W into 8 ?)POWER BANDWIDTH10 Hz to 100 kHz (+0 -3 dB, 225 W into 8 ?)FREQUENCY RESPONSE20 Hz to 20 kHz (+0 -0.15 dB), 5 Hz to 100 kHz (+0 -2 dB)INPUT SENSITIVITY1.5 Vrms in for 225 W out into 8 ?INPUT IMPEDANCE10 k? (RCA), 15 k? (XLR)DAMPING FACTOR360 at 1 kHz (ref. 8 ?)S/N RATIO120 dB, A-weighted (ref. 225 W)CROSSTALK-78 dB at 1 kHzVOLTAGE GAIN29 dBSLEW RATE30 V/µsSWITCHESFront PanelPower (On/Off)Rear PanelOn/Off Modes (Trigger, Manual, Auto), Inputs (RCA, XLR)POWER OUTPUT (Continuous RMS, 20 Hz to 20 kHz, <0.1% THD) Impedance 8? 4? 2? # of Channels Driven 1 All 1 All 1 All 225 W 200 W 370 W 300 W 535 W 410 W *Special Test Conditions Required for 2 ?POWER REQUIREMENTSSUPPLY VOLTAGE105 to 130 V, 60 HzPOWER CONSUMPTION800 WDIMENSIONSHeight7-5/8 inches (19.4 cm) including feetWidthFaceplate 19-1/4 inches (49 cm), Chassis 17-1/4 inches (43.8 cm)Depth13-1/2 inches (34.3 cm)Weight (unpacked)34 lb (15.5 kg)