Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #13 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches.Please refer to the photo. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwMounting nut/washerPHONO cableInstruction manual (copy)(Japanese)Mounting gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #12 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches.Please refer to the photo. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwMounting nut/washerPHONO cableInstruction manual (copy)(Japanese)Mounting gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #11 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.There is some tarnish on the arm base.Other appearance is a beautiful product without any noticeable scratches. Please refer to the photo. *Turntables and other equipment (excluding accessories for the unit) shown in the photos are for presentation purposes only and are not part of the product. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwMounting nut/washerPHONO cableInstruction Manual (copy) (Japanese)Mounting gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #7 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. With original box. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Titanium NitrideArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmRotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5gShell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 38mm? Accessories WeightsWeight fixing screwMounting nut/washerHead shell/lead wireCartridge fixing screwsPHONO cableInstruction Manual (original) (Japanese)Mounting gaugeSpannerFlat head screwdriverOriginal box / Outer box Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #6 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. With original box. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Titanium NitrideArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmRotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5gShell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 38mm? Accessories WeightWeight fixing screwMounting nuts/washersHead shell/lead wireCartridge fixing screwsPHONO cableInstruction Manual (copy)Mounting gaugeSpannerFlat head screwdriverOriginal box Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage AudioDescriptionThe universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium and further hardened with nitrogen, to achieve 1.6 times mechanical strength and high internal loss while reducing weight by 85% compared to conventional aluminum pipe. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Type Braking variable dynamic damping systemUniversal tone armEffective bearing distance 30mm both horizontally and verticallyArm pipe High-strength titanium pipe with special nitriding treatmentArm effective length 250mmArm overall length range 322mm?350mmArm rear length range 66mm - 94mmArm height adjustment mechanism 45mm - 90mm (helicoid part 6mm)Overhang 15mmHorizontal tracking error angle +1.1°(inside of 30cm record)+2.1°(30cm record circumference)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency 9.8Hz(Compliance: 12x10-6cm/dyneCartridge dead weight: 6.5g, needle pressure: 1.25g)Arm resonance sharpness (Q) 6dB or less (at optimum adjustment)Needle pressure adjustment range 0 to 3gShell weight 9.5gCartridge mounting dimensions JIS standard 12.7mm (1/2) mounting distanceShell terminal lug 1.2mm?, lug for 4-pin terminalApplicable cartridge weight 5g-10gArm mounting hole diameter 38mm?Optional: SH-100G1 balance weight for EPA-100 ($20,000)Type Variable dynamic damping typeArm effective weight 25.5g (with cartridge dead weight 9.5g and needle pressure 1.25g)Arm resonance frequency 9.1Hz(Compliance: 12x10-6cm/dyneCartridge dead weight: 9.5g, needle pressure: 1.25g)Resonance sharpness (Q) 6dB (at optimum adjustment)Dimensions 66mm - 94mm (from horizontal rotation axis to highest part of weight) Shipping FedEx?or DHLInternational Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. Thank you for your understanding.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwHead shell (Technics)Lead wireMounting nut/washerPHONO cableInstruction Manual (copy)(Japanese)Installation gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Braccio pickup universale con smorzamento dinamico Audio vintage n. 4 Domo Arigato! Benvenuto, grazie per la tua visita. Descrizione Operazione confermata con i seguenti contenuti. Uscita da entrambi i canali.Velocità di discesa del sollevatore (Rifornimento olio).Ogni punto di regolazione, sensazione di funzionamento.Regolazione dellaltezza, ecc. Lucidato e pulito in ogni sua parte.Laspetto è un bellissimo prodotto senza graffi evidenti. Si prega di fare riferimento alla foto. Panoramica Il braccio universale è stato sviluppato per risolvere il problema principale dello smorzamento della risonanza a bassa frequenza nei sistemi di pickup. Il meccanismo di smorzamento dinamico variabile è in grado di smorzare adeguatamente le risonanze a bassa frequenza sia di tipo ad alta che a bassa compliance, esaltando tutto il potenziale della cartuccia. Il peso principale è diviso e supportato da una molla su un lato, e galleggia sullaltro lato grazie alla forza di attrazione tra due magneti posizionati uno di fronte allaltro nella parte posteriore del peso e del selettore di smorzamento. La risonanza del peso viene smorzata da olio siliconico viscoso e da un cilindro di smorzamento, smorzando efficacemente la risonanza dellintero sistema di pickup e riducendo con successo la risonanza a meno della metà rispetto ai sistemi convenzionali. La frequenza di risonanza del peso principale può essere regolata con il selettore di smorzamento sul retro del peso principale in base alla conformità della cartuccia, e la quantità di frenata può essere impostata su un valore appropriato. Il tubo del braccio, con diametro esterno di 9,5 mm e spessore di 0,5 mm, è realizzato con un braccio in nitruro di titanio, realizzato in titanio leggero e meccanicamente resistente, ulteriormente indurito dallazoto. La struttura di supporto del braccio è realizzata in tubo di nitruro di titanio. Sia la sezione di rotazione orizzontale che quella verticale del braccio sono supportate da un sistema di sospensione cardanica che utilizza cuscinetti con cuscinetti girevoli ad alta precisione prodotti internamente. Gli assi di rotazione orizzontale e verticale si intersecano in un unico punto, riducendo al minimo le differenze nella sensibilità iniziale e nella sensibilità in tutte le direzioni di rotazione. I rubini, il cui coefficiente di attrito è circa 1/3 di quello dellacciaio, vengono superfiniti in sfere con una sfericità di ±0,5?m e vengono utilizzati 20 rubini.In combinazione con il sistema di sospensione cardanica, raggiunge unelevata sensibilità iniziale di 5 mg. Specifiche Tipo: braccio universale con smorzamento dinamico variabileGioco effettivo dei cuscinetti: 30 mm sia in orizzontale che in verticaleTubo del braccio: tubo al boro titanioLunghezza effettiva del braccio: 250 mmIntervallo di lunghezza del braccio: da 322 mm a 350 mmIntervallo di lunghezza posteriore del braccio: 66,5 mm - 94,5 mmIntervallo di regolazione dellaltezza del braccio: 44 mm - 64 mm (parte elicoidale 20 mm)Sporgenza: 15 mmAngolo di errore di tracciamento orizzontale: +1°6(circonferenza interna del record da 30 cm), +2°6(circonferenza esterna del record da 30 cm)Sensibilità dellasse di rotazione: sensibilità orizzontale, verticale, iniziale 5 mgPeso effettivo del braccio: 22 g (peso morto della cartuccia 6,5 g, pressione dellago 1,25 g)Frequenza di risonanza del braccio: 9,8 Hz, (Conformità: 12x10-6 cm/dyne, peso cartuccia 6,5 g, pressione ago 1,25 g)Nitidezza della risonanza del braccio (Q): 6 dB o meno (con regolazione ottimale)Intervallo di regolazione della pressione dellago: da 0 a 3 gPeso del guscio: 9,5 g (alluminio boro)Capocorda terminale a guscio: 1,2 mm?, capocorda per terminale a 4 pinPeso della cartuccia applicabile: da 5 g a 10 gDiametro del foro di montaggio del braccio: 62 mm? Accessori PesiVite di fissaggio del pesoGuscio della testa (Tecnica)Cavo principaleDado/rondella di montaggioCavo FONOManuale di istruzioni (copia)(giapponese)Calibro di installazione (copia) Spedizione La spedizione è disponibile solo per lindirizzo registrato su eBay. La spedizione è entro Fedex O SME. Spedizione gratuita ritorna Politica di restituzione incondizionata Il servizio e la soddisfazione del cliente sono molto importanti per noi.Ho una politica di restituzione incondizionata se notificata entro 30 giorni dalla ricezione dellarticolo. Tutti gli articoli restituiti devono essere nella condizione originale.Tutte le richieste di reso devono essere effettuate entro 30 giorni dal ricevimento dellarticolo. Per favore contattami prima per il reso prima di rispedirmelo.Le spese di spedizione della merce restituita sono a carico dellacquirente. Acquirenti internazionali Notare che:I dazi doganali, le tasse e le spese non sono inclusi nel prezzo dellarticolo o nelle spese di spedizione.Queste spese sono a carico dellacquirente.Si prega di verificare con lufficio doganale del proprio paese per determinare quali saranno questi costi aggiuntivi prima dellofferta/acquisto.Queste spese vengono normalmente riscosse dalla società di spedizione (spedizione) o al momento del ritiro dellarticolo: non confonderle con spese di spedizione aggiuntive.Non contrassegniamo i valori della merce al di sotto del valore né contrassegniamo gli articoli come regali: le normative governative statunitensi e internazionali vietano tale comportamento. Mi dispiace, ma non possiamo organizzarlo perché è illegale in Giappone.Grazie.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwHead shell (Technics)Lead wireMounting nut/washerPHONO cableInstruction Manual (copy)(Japanese)Installation gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories All accessories are shown in the photos. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories All accessories are shown in the photos. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Fidelity Audio HPA-100 headphone amplifier, original box -5 star review WhatHiFi. In excellent condition....now have an amplifier with a headphone amplifier. RM Special Delivery in UK, collection welcome....or overseas but only using eBays Global Shipping If you appreciate wide-open, clear and detailed sound then you need to hear our Fidelity Audio HPA-100 headphone amplifier. Starting with the power supply, this solidly handmade, dual mono amp features a high quality toroidal transformer, ultra-fast HEXFRED rectifier and our own Fidelity Audio smoothing capacitors.The IEC power inlet allows you to connect a power cable of your choice. Volume control is taken care of by the Alps Blue, a volume control famed for its excellent channel balance. High-grade decoupling caps by Wima and Rubycon help to ensure the sound is never less than clean and musical, whilst also guaranteeing exceptional longevity. Extensively tested using headphones from Grado, Beyerdynamic and Sennheiser you can be sure the Fidelity Audio HPA-100 headphone amplifier will satisfy the demands of your cans (see full specifications) and of your ears. Compact in size and sturdy in build the Fidelity Audio HPA-100 headphone amplifier will neatly grace any Hi-Fi rack or desktop. Headphone impedance range: 12 to 600 Ohms Headphone Jack: 1/4 inch (6.35mm) Power output: (rms, both channels fully driven) 32 Ohms: > 500mW/channel Distortion: (THD + N @ 1kHz): 0.00006% Frequency response: (-3dB) 32 Ohms load: 10Hz 35kHz; 300 Ohms load: 10Hz 38kHz Channel balance: 0.5dB approx Output Stage: 2x High Performance, low distortion high fidelity 250mA audio buffers Supply voltage: AC 230V +/- 10% DC voltage: Low Noise Linear dual power supply +15V & -15V Size: (approx.) W: 104 x H:56 x D:245 (mm) including controls & feet Weight: 1.04 Kg (1.55 Kg including packaging) Hand built to order in UK Dual mono design Large internal dual voltage power supply Ultra Fast HexFred Rectifying Diodes Super low ESR high ripple smoothing capacitors Quality Audio grade parts used throughout High grade pcb copper tracks for optimal signal & voltage transfer Gold Plated RCA Connectors Easily drives Grado (eg 325i), Sennheiser (eg HD650, HD800), Beyerdynamic (eg T1 Tesla) &; AKGs (eg K702 , Q701 IEC mains input 2 year parts and labour warranty The unit IS NOT supplied with an RCA lead Mains lead supplied