Triple stack, consisting of the DAC, the Tube Buffer and the power supply for both. With the two power supply cables from the power supply to each active unit - one for the Dac, and one for the tube buffer. thoughtfully re-capped with premium and nonmagnetic film caps (the big blue ones), and opamps socketed for easier upgrading. All while referencing the tech manuals for the chips involved, of course. Tube buffer also mildly modded with newer output caps w/non-magnetic polypropylene bypass caps Works beautifully.

Sie bieten hier auf einen X-Dac V3 der Firma Musical Fidelity. Gerät funktioniert einwandfrei. Die technischen Daten laut Herstellerseite: DAC architecture 24 bit Delta-Sigma (bitstream) Dual differential 8 times oversampling 192kHz Sampling frequencies 8 to 108kHz Data types 16, 20, 24 bit word lengthsInputs RCA 75 Ohms (S/PDIF), TOSLINK optical Outputs RCA left & right audio,RCA digital loop out Frequency response 10Hz to 20kHz +0 / -0.2dB Signal / noise ratio > 121dB A weighted ref. full output Total harmonic distortion < 0.002% 10Hz to 20kHz Total correlated jitter 110dB 20Hz to 20kHz Linearity < 0.1dB down to -96dB Audio output at digital 0dB 2.2VRMS at 1kHz nominal, 50 Ohms impedance Power requirement 12 - 0 - 12Volts AC 500mA(via mains adaptor supplied) natürlich mit original Netzteil. Versand erfolgt sofort nach Geldeingang.

MUSICAL FIDELITYX-DAC-V3 AND X-PSU-V3 COMBO UPGRADED COMPONENTS THIS X-DAC AND POWER SUPPLY COMBO HAS SEEN MINIMAL USE OVER THE YEARS. KEPT AS A SPARE, IT WAS RARELY INSTALLED IN A SYSTEM. COSMETICS ARE EXCELLENT. NO OBVIOUS FLAWS ON THE DAC. THE X-PSU POWER SUPPLY HAS A SMALL FLAW AT THE REAR CORNER ON ONE FIN.....WHICH I BELIEVE WAS A FACTORY DEFECT. ITS ONLY VISIBLE FROM THE REAR. THE X-PSU-V3 POWER SUPPLY IS ORIGINAL AND UNMOLESTED. ITS JUST AN OVERSIZE TRANSFORMER THAT ALLOWS YOU TO CONNECT OTHER V3 COMPONENTS INTO ONE POWER SUPPLY. I FELT IT DID PERFORM BEST WHEN ONLY 2 COMPONENTS MAXIMUM WERE CONNECTED.3 POWER CONNECTOR CORDS FOR ADDITIONAL UNITS ARE INCLUDED. ONE CORD IS MISSING AND HAS DISAPPEARED. A NEW AC POWER CARD IS INCLUDED. THE X-DAC-V3 HAS HAD SIGNIFICANT COMPONENT UPGRADES. THESE MODS WERE INSPIRED BY AN ARTICLE ON THE BURSON AUDIO WEBSITE BACK WHEN THEY FIRST INTRODUCED (HDAM) DISCRETE OP-AMPS, A NUMBER OF YEARS AGO. SOME UPGRADES WERE TAKEN FROM THE ARTICLE. OTHER UPGRADES WERE MINE. THE DAC POWER SUPPLY CAPACITANCE WAS VASTLY INCREASED USING NICHICON MUSE AUDIO GRADE CAPS. CARE WAS TAKEN TO INSURE THE (STACK OF) CAPS WERE SOLIDLY MOUNTED TO REDUCE/ELIMINATE ANY VIBRATIONAL EFFECT. THE STANDARD BRIDGE RECTIFIER WAS REPLACED WITH INDIVIDUAL HYPER-FAST/SOFT RECOVERY DIODES. ALL OTHER ELECTROLYTIC CAPACITORS WERE REPLACED WITH SANYO OS-CON POLYMER AND ELNA SILMIC II AS THE APPLICATION REQUIRED. NON-POLAR CAPS WERE REPLACED WITH (A LARGE NUMBER OF) WIMA POLYPROPYLENE FILM AND OTHER POLYPROPYLENE FILM CAPS. POLYPROPYLENE BY-PASS CAPACITORS WERE ADDITIONALLY INSTALLED UNDERNEATH THE CIRCUIT BOARD AS NEEDED. AT THE ANALOG OUTPUT, THE 2 ELECTROLYTIC NON-POLAR CAPS WERE REPLACED WITH NICHICON MUSE, BY-PASSED WITH POLYPROPYLENE FILM/FOIL CAPACITORS. THE RCA OUTPUT JACKS ARE CONNECTED WITH SHIELDED SILVER PLATED WIRING. HEATSINKS WERE INSTALLED ON SURFACE MOUNTED ICS AND MICRO PROCESSORS. LASTLY, I DID INSTALL SOME BURSON DISCRETE OP-AMPS, BUT LATER REMOVED THEM. WHILE THE OP-AMPS DID SLIGHTLY ALTER THE SOUND, I COULD NOT DEFINITIVELY STATE THERE WAS AN ACTUAL IMPROVEMENT AND WORTH THE ADDITIONAL COST IN THIS APPLICATION. THE VAST MAJORITY OF AUDIBLE SOUND/PERFORMANCE IMPROVEMENTS CAME FROM THE COMPONENT UPGRADES THAT WERE COMPLETED FIRST. NOT THE INSTALLATION OF THE DISCRETE OP-AMPS, THAT WERE INSTALLED LAST. THE ORIGINAL 5532 OP-AMPS ARE INSTALLED IN SOCKETS AND CAN BE EASILY REPLACED IF, SHOULD THE BUYER WANT TO EXPERIMENT WITH OTHER OP-AMPS/HDAMS. THIS UPGRADED V3-DAC AND POWER SUPPLY COMBO PROVIDES A SMOOTH ANALOG SOUND THAT RIVALS NEWER, OR MORE EXPENSIVE DACS.

Zum Verkauf steht ein kompakter schnörkelloser DAC - Musical Fidelity X-Dac V3 in sehr gutem technischen und optischen Zustand.Exzellenter Klang. Zum Lieferumfang gehört das externe Netzteil und die Bedienungsanleitung. Technische Daten - siehe Fotos! Da es sich hier um einen Privatverkauf handelt: Ich schließe jegliche Sachmängelhaftung aus. Dieser Verkauf erfolgt unter Ausschluss jeglicher Gewährleistung. Der Kaufgegenstand wird unter Ausschluss jeglicher Gewährleistung verkauft. Der Ausschluss gilt nicht für Schadensersatzansprüche aus grob fahrlässiger bzw. vorsätzlicher Verletzung meiner Pflichten als Verkäufer sowie für jede Verletzung von Leben, Körper und Gesundheit.

Normal 0 false false false RU X-NONE X-NONE Normal 0 false false false RU X-NONE X-NONE MicrosoftInternetExplorer4 Welcome to bid for Premium Power Supply Unit for Musical Fidelity Valve X Series Ver3 and Ver 8 This is high quality power developed especially for use with X series Version 3 and 8 family of audio gears from Musical Fidelity.The PSU provides highly stable and purified AC voltage output of 24 (12-0-12) volt, exactly as specified for the X Series devices from Musical fidelity in V3 and V8 editions This psu is suitable for ALL VERSION 3 X Series VALVE ITEMS:X10D ver3XDac ver 3XLps ver3XCan ver3AND FOR 2 OF VERSION 8 X Series VALVE ITEMS: XLps V8 and XCans V8 but not suitable for some V8 models, like X-Ray or X-plora - please ask if you are in doubt Please note that similar PSU to be used with Musical Fidelity Ver.1 and 2 (AC 12 V) audio items likeX-10D valve bufferX-DACs (all models)X-PreampX-ToneX-LP and Lps phono stagesX-CAN headphone amplifiers - in it V1 and V2 editions.ARE PRESENTED IN OUR PARALLEL AUCTIONS please have a look there or ask about suitability for your system if you are in doubt PSU presented in the auction capable built with very high audio grade power toroidal transformer and has 3 times more output power that the original wall adaptor and improves sonic performance of the deviceslisted above as well as many other types where AC 24 Volt is power requirement.Please ask if you are in doubt relating suitability of this PSU with your particular item. The PSU is assembled in solid aluminium frame marched aestetically with X series from Musical Fidelity.This is not an universal power supply adopted for audio gears, but dedicated and especially developed for use with Musical Fidelity X series V3 power source.In particular, not just output voltage is matched, but output impedance and regulation characteristics are tuned optimal for the best sonic results when paired with Musical Fidelity audio equipment.This item is to be supplied with 70 cm power cable to connect to a musical Fidelity item.If you wish this cable of another length or extra IEC mains cable (free of charge) please let us know by message. Delivery and possible return.This player will be supplied with replacement remote control,. Shipping cost of £9 quoted is related to UK mainland destinations only and includes insurance. Could be shipped any other location worldwide, but, please, ask for quotation before bidding if you are outside the UK mainland. We combine shipments, just ask if you buy more than one item. In particular, any cable presented in our auctions, if purchased, will be sent with this item without extra postage. Please, note that we ship in 5 days after he payment is cleared, please allow some extra time for delivery. Attention of International bidders: we will be pleased to ship worldwide. Overseas delivery could cost from £29 (USA, China) to £45(Australia, South America) We charge an actual minimal for international shipment, please, ask for quotation before bidding to be sure. Please, note that overseas delivery can take up to 12 working days. Item is fully tested and return is accepted within 2 week after delivery and exclusively in shape as it was shipped, i.e. perfect working condition. In this case 100% of auction price and shipment cost will be refunded. Return of nonworking, damaged or scratched item is not accepted and will be not refunded. Return shipment cost is on Buyer’s side.

Normal 0 false false false RU X-NONE X-NONE Normal 0 false false false RU X-NONE X-NONE MicrosoftInternetExplorer4 Welcome to bid for Premium Power Supply Unit for Musical Fidelity Valve X Series Ver3 and Ver 8 This is high quality power developed especially for use with X series Version 3 and 8 family of audio gears from Musical Fidelity.The PSU provides highly stable and purified AC voltage output of 24 (12-0-12) volt, exactly as specified for the X Series devices from Musical fidelity in V3 and V8 editions This psu is suitable for ALL VERSION 3 X Series VALVE ITEMS:X10D ver3XDac ver 3XLps ver3XCan ver3AND FOR 2 OF VERSION 8 X Series VALVE ITEMS: XLps V8 and XCans V8 but not suitable for some V8 models, like X-Ray or X-plora - please ask if you are in doubt Please note that similar PSU to be used with Musical Fidelity Ver.1 and 2 (AC 12 V) audio items likeX-10D valve bufferX-DACs (all models)X-PreampX-ToneX-LP and Lps phono stagesX-CAN headphone amplifiers - in it V1 and V2 editions.ARE PRESENTED IN OUR PARALLEL AUCTIONS please have a look there or ask about suitability for your system if you are in doubt PSU presented in the auction capable built with very high audio grade power toroidal transformer and has 3 times more output power that the original wall adaptor and improves sonic performance of the deviceslisted above as well as many other types where AC 24 Volt is power requirement.Please ask if you are in doubt relating suitability of this PSU with your particular item. The PSU is assembled in solid aluminium frame marched aestetically with X series from Musical Fidelity.This is not an universal power supply adopted for audio gears, but dedicated and especially developed for use with Musical Fidelity X series V3 power source.In particular, not just output voltage is matched, but output impedance and regulation characteristics are tuned optimal for the best sonic results when paired with Musical Fidelity audio equipment.This item is to be supplied with 70 cm power cable to connect to a musical Fidelity item.If you wish this cable of another length or extra IEC mains cable (free of charge) please let us know by message. Delivery and possible return.This player will be supplied with replacement remote control,. Shipping cost of £9 quoted is related to UK mainland destinations only and includes insurance. Could be shipped any other location worldwide, but, please, ask for quotation before bidding if you are outside the UK mainland. We combine shipments, just ask if you buy more than one item. In particular, any cable presented in our auctions, if purchased, will be sent with this item without extra postage. Please, note that we ship in 5 days after he payment is cleared, please allow some extra time for delivery. Attention of International bidders: we will be pleased to ship worldwide. Overseas delivery could cost from £29 (USA, China) to £45(Australia, South America) We charge an actual minimal for international shipment, please, ask for quotation before bidding to be sure. Please, note that overseas delivery can take up to 12 working days. Item is fully tested and return is accepted within 2 week after delivery and exclusively in shape as it was shipped, i.e. perfect working condition. In this case 100% of auction price and shipment cost will be refunded. Return of nonworking, damaged or scratched item is not accepted and will be not refunded. Return shipment cost is on Buyer’s side.

Welcome to bid for Premium Power Supply Unit for Musical Fidelity X Series Ver 3 and Ver 8DACs and Preamps with Valve Output This is high quality power developed especially for use with X series Version 3 and Version 8 family of audio gears from Musical Fidelity.The PSU provides highly stable and purified AC voltage output of 24 (12-0-12) volt, exactly as specified for the following devices from Musical fidelityX10D V3 Valve BufferX Cans V3X DAC V3 DacX LPS V3 Phono Stage Preamplifiersuitable for V8 models XLps V8 and XCans V8but not suitable for some V8 models, like X-Ray or X-plora - please ask if you are in doubt Please note that similar PSU to be used with Musical Fidelity Ver.1 and Ver 2 (AC 12 V) audio items likeX-10D valve bufferX-DACs (all models)X-PreampX-LP phono stageX-CAN headphone amplifiers - in it V1 and V2 editions. PRESENTED IN OUR PARALLEL AUCTION please have a look there or ask about suitability for your system if you are in doubt PSU presented in the auction capable built with very high audio grade 30W power toroidal transformer and has 3 times more output power that the original wall adaptor and improves sonic performance of the deviceslisted above as well as many other types where AC 24 Volt is power requirement.Please ask if you are in doubt relating suitability of this PSU with your particular item. The PSU is assembled in solid aluminium frame matched aestetically with X series from Musical Fidelity.This is not an universal power supply adopted for audio gears, but dedicated and especially developed for use with Musical Fidelity X series V3 power source.In particular, not just output voltage is matched, but output impedance and regulation characteristics are tuned optimal for the best sonic results when paired with Musical Fidelity audio equipment.We show connection of this PSU to X10D V3 in few pictures as example of use, but this the X10 is not included and shown for illustration onlyMains cable is not normally included, but please let us know if you need one to be sent with the psu, we will supply it. Delivery and possible return.This player will be supplied with replacement remote control,. Shipping cost of £10 quoted is related to UK mainland destinations only and includes insurance. Could be shipped any other location worldwide, but, please, ask for quotation before bidding if you are outside the UK mainland. We combine shipments, just ask if you buy more than one item. In particular, any cable presented in our auctions, if purchased, will be sent with this item without extra postage. Please, note that we ship in 5 days after he payment is cleared, please allow some extra time for delivery. Attention of International bidders: we will be pleased to ship worldwide. Shipping cost of £19 quoted is initial estimation for EU only.Overseas delivery could cost from £36 (USA, China) to £30(Australia, South America) We charge an actual minimal for international shipment, please, ask for quotation before bidding to be sure. Please, note that overseas delivery can take up to 12 working days. Unfortunately we can not ship to Vietnam and Ukraine. Item is fully tested and return is accepted within 2 week after delivery and exclusively in shape as it was shipped, i.e. perfect working condition. In this case 100% of auction price and shipment cost will be refunded. Return of nonworking, damaged or scratched item is not accepted and will be not refunded. Return shipment cost is on Buyer’s side.