This Hypex amplifier was built in 2020 and uses the Ncore NC252MP board (with the power supply and the amplifier integrated on one PCB) built into a Ghent aluminum chassis. It is in excellent working and cosmetic condition. Hypex specs the amp at 150 WPC into 8 ohms, and 250 WPC into 4 ohms. It includes a 12v remote trigger. The XLR input connectors are Neutrik gold, and the binding posts are upgraded to Superior BP30 gold. Internal audio input wiring is Mogami 2549 and speaker wiring is Belden 8471. This amp is very efficient, drawing only 11.5 watts at idle. I measured gain at 25.6dB, both channels identical.

This is a very nice class-D stereo amplifier I purchased from Ghent Audio in 2015. I really enjoyed my time with it but I need to let go of some things. Includes power chord. Main FeaturesWell designed for Stereo Power Amplifier, based on the latest ICEpower Class-D technology125w x 2ch(4?), or 65w x 2ch(8?), both Balanced XLR and RCA input connectionsLatest design of buffer stage, high-bandwith & high impedance, suitable for most of pre-ampsMore balance, more detail, no noise, neutral sonic colorationLed Color: RCA(Blue) and XLR(Green) switched by toggle switchLed Dimmer: Led brightness could be adjusted manually Brighter | Normal brightness | Power-off (Hiding under the bottom of front-panel so to adjust from front easily)Hi-End Neutrik & CMC components, silver-plated Teflon signal wire inside100% Aluminum case, perfect Brushed carftwork & Laser Inscription, excellent cooling performanceWell assembled & carefully tuned, Ready-to-PlayPower Supply: 115VAC or 230VAC 50/60 Hz (Pre-Setting in factory, according to voltage choice)Color: Black Key SpecificationsLatest buffer-stage, specific Stereo design, powered by ICEpower technologyInput connections: Single-ended RCA or balanced XLRRCA input impedance: 100KohmsBalanced input impedance: 200KohmsOutput connections: 2-sets of safety sockets (banana plug compatible)Maximum Power Output: 125W 4 ohms, 65W 8 ohms per channelPower Output 1% THD: 120W 4 ohms, 60W 8 ohms per channelMinimum Load: 3 ohms per channelPeak Output Current: 30 amperesFrequency Response: +/- 0.15dB 20Hz-20KHz, All loadsTHD+N: 0.003% 1W, 100Hz, 4 ohmsIMD (CCIF): 0.0009%, 10W, f =18.5kHz, 1kHz, PO =10WOutput Noise: 30uVRMS A-weighted 10Hz-20KHzVoltage gain:: 24.8dBDamping factor: >1000Dynamic Range: 117dBSensitivity: 1.26VoltsPower On usage: 9.5WPower Off usage: 0.0WInternally Set Operating Voltages: 100-120VAC or 230-240VAC 50/60 HzProtection: Short circuit, Thermal & Over-current protectionSize: 200 x 80 x 210mm (W x H x D)Weight: 4.4lbs, 2.0Kg

Schiit Audio Modi 3 DAC Silver - Ghent Audio Cables - Micro USB.

Working ICEPOWER Power Amplifier ICE125ASX2 2CH Audio Amp Module + Ghent Case (prebuilt)

Ghent audio case backplate only for XLR,3 sets of XLR sockets solder type 2 sets and screw type 1 set. Only solder type does fit backplateVarious small bolts and spacersCrimps blue, butt end crimps red/blue/yellow Chinese.Some left over ICEpower cables for 200 AS 2

Working ICEPOWER Power Amplifier ICE125ASX2 2CH Audio Amp Module + Ghent Case (prebuilt)

Working ICEPOWER Power Amplifier ICE125ASX2 2CH Audio Amp Module + Ghent Case (prebuilt)

Ghent audio case backplate only for XLR,3 sets of XLR sockets solder type 2 sets and screw type 1 set. Only solder type does fit backplateVarious small bolts and spacersCrimps blue, butt end crimps red/blue/yellow Chinese.Some left over ICEpower cables for 200 AS 2

ICE-POWER 2x125W HIFI Amplifier Board ICE125ASX2 installed in custom Ghent Audio Case. All soldering connections were soldered with solver solder for optimal sound quality. This amp I built and it is 2 months old. This isa very neutral and clean amp showcasing one of the best Class D board out there. Its setup for 2 channel however the board an be made into a BTL Mono easily should you want to convert it yourself.Power rating is 125 watts into 4 ohm x 2

ICE-POWER 2x125W HIFI Amplifier Board ICE125ASX2 installed in custom Ghent Audio Case. All soldering connections were soldered with solver solder for optimal sound quality. This amp I built and it is 2 months old. This isa very neutral and clean amp showcasing one of the best Class D board out there. Its setup for 2 channel however the board an be made into a BTL Mono easily should you want to convert it yourself.Power rating is 125 watts into 4 ohm x 2

Ghent audio case backplate only for XLR,3 sets of XLR sockets solder type 2 sets and screw type 1 set. Only solder type does fit backplateVarious small bolts and spacersCrimps blue, butt end crimps red/blue/yellow Chinese.Some left over ICEpower cables for 200 AS 2

Ghent audio case backplate only for XLR,3 sets of XLR sockets solder type 2 sets and screw type 1 set. Only solder type does fit backplateVarious small bolts and spacersCrimps blue, butt end crimps red/blue/yellow Chinese.Some left over ICEpower cables for 200 AS 2

ICE-POWER 2x125W HIFI Amplifier Board ICE125ASX2 installed in custom Ghent Audio Case. All soldering connections were soldered with solver solder for optimal sound quality. This amp I built and it is 2 months old. This isa very neutral and clean amp showcasing one of the best Class D board out there. Its setup for 2 channel however the board an be made into a BTL Mono easily should you want to convert it yourself.Power rating is 125 watts into 4 ohm x 2