Edwards Home Entertainment and Design, an appointed and displaying dealer for McIntosh, Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Gold Note, Marantz, Rose HiFi, AudioQuest, Nordost, as well as part of the Verified Premier Dealer Program on AudioGon, is offering this VPI Classic 3 table with a phenomenal cartridge.This table has the Lyra ATLAS cartridge, close to $12,000 alone. This table is piano black, comes with its cover and all packaging and boxes, BUT - if shipping is necessary, you must reach out to the numbers below. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997 and is now an authorized dealer for McIntosh (displaying C2700, C22, C12000, MC462, MC275vi, MC1.25s, MEN220, MT-10, MT-5, MA12000, MA352, MA252, MPC500, MPC1500, MHA200, speakers and interconnect cabling), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3), Focal (displaying Scala EVO, Sopra3, Sopra2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5s2, S5, X3s2), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Fyne Audio (displaying F1-12, F1-8, 502SP, F700), HiFiROSE (displaying the RS150, RS250 and RS520), Parasound (displaying JC-1+, JC2BP, JC-5, JC-3+, and HINT6), Jeff Wells Audio (displaying Commander II and Innamorata II), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812, S/512, and T9/x), Perlisten (displaying the S7t and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), AudioQuest (displaying all power centers, 7000, 5000, 3000, Thunderbird, Black Beauty, Pegasus cabling), SolidSteel (displaying HyperSpike stands and amp stands), NEO Luxury Audio Racks (displaying the Quattron), Bossocontinuo (displaying the McRack) Reference. Visit the EHEADAudio com site in South San Francisco, CA for direct phone (begins with 925) / voice / text support. We are always looking to buy quality used gear. Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

Edwards Home Entertainment and Design, an appointed and displaying dealer for McIntosh, Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Gold Note, Marantz, Rose HiFi, AudioQuest, Nordost, as well as part of the Verified Premier Dealer Program on AudioGon, is offering this VPI Classic 3 table.This table is in fine shape, without issue - just had a new cartridge installed. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997 and is now an authorized dealer for McIntosh (displaying C2700, C22, C12000, MC462, MC275vi, MC1.25s, MEN220, MT-10, MT-5, MA12000, MA352, MA252, MPC500, MPC1500, MHA200, speakers and interconnect cabling), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3), Focal (displaying Scala EVO, Sopra3, Sopra2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5s2, S5, X3s2), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Fyne Audio (displaying F1-12, F1-8, 502SP, F700), HiFiROSE (displaying the RS150, RS250 and RS520), Parasound (displaying JC-1+, JC2BP, JC-5, JC-3+, and HINT6), Jeff Wells Audio (displaying Commander II and Innamorata II), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812, S/512, and T9/x), Perlisten (displaying the S7t and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), AudioQuest (displaying all power centers, 7000, 5000, 3000, Thunderbird, Black Beauty, Pegasus cabling), SolidSteel (displaying HyperSpike stands and amp stands), NEO Luxury Audio Racks (displaying the Quattron), Bossocontinuo (displaying the McRack) Reference. Visit the EHEADAudio com site in South San Francisco, CA for direct phone (begins with 925) / voice / text support. We are always looking to buy quality used gear. Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

?ª˜¨¨?ª˜¨¨¨¨˜ª¤.¸*•.¸*•¸? ? Super eBayer ??¸•*¸.•*´¸.¤ª˜¨¨¨¨˜ª?¨¨˜ª? I do provide excellent service to every buyer. Please see my feedback before you bid, and see that everyone is happy with my prices, my product .... and my service. AUCTION IS OVER ON SUNDAY AT 3PM PACIFIC, AND 6 PM EASTERN TIME HIGH END VPI TABLE AND PLATTER, AS PICTURED Hello, Lets get this gone. Tell everyone you know. If you are looking, you know someone that wants it. This was NOT my personal item. I did not use it, test it, or know any more about it than I have pictured or been told by VPI or other VPI table owners. You are bidding on what you see pictured. I purchased an entire recording studio. All high end gear. No issues with any pieces, and many in the thousands of dollars. Go look at my feedback. Some pieces I sold on a different site I prefer for this type of gear. I have had much interest in this item regarding shipping. So, if I am to ship it, it will come with certain conditions, so please read before clicking anything. First, it will come in two boxes. Yes, I have the original box. But, the platter is just too heavy. I can wrap the platter well, and place it in the original box. There is no way I can repack this and get it to you. I would prefer to have professional UPS packaging of the table. I got a quote. $85. Yes, it is too much. If you want it in one piece, and insurable, this is it. Sorry, but it is what it is. So, recap. Ill pack the platter. No charge. You will be paying to ship it in the original box, with the arm. And the turntable will be packed by UPS for $85. This would be at your cost. Then, you would pay for the shipping of the turntable as well. And both boxes would then be insured for the $999 cap per box. Thats as much as UPS will cover through ebay. Two boxes, two thousand dollars insurance. If you want to insure it for more, that would be up to you to arrange. I accept no responsibility on this sale. And, you would need to file a claim for any insurance, if damaged or lost. Not me. This is why I want UPS to pack the table. Then, there is a shot if a claim is made if it gets lost, stolen or damaged, as they packed it. I can get the platter to you fine, but insured also just in case. Total cost for shipping would be $265. I apologize but it is what it is. I am old. I do not really even want to ship it, but too many people have been asking about shipping it. The package is worth $3500-$5,000. This is worth noting, as well as the rarity and high value placed on the platter by audiophiles. You assume all risk. I you are willing to pick it up instead, Ill deduct $75 for gas from what you pay. This is as good as I can do, given the circumstances. And dont ding my shipping stars. As it is I will need to drive it 45 minutes just to drop it off, which I am happy to do. I can only do my very best, and my batting score is perfect, as you can see. 100%!!! Absolutely and positively sold as is, with no variations on the terms. Please DO NOT ASK. I am only asking $2,000 for the table and the platter. This is a steal. Ask VPI themselves. I did. I have done my very best to present this item honestly and accurately. No nonsense please. My understanding is that this is one of the most sought after and rare ever sold by VPI. Please read the following: Comes with manuals and vintage warranty registrations. I also contacted Jim at VPI, and here is what he told me. Its definitely an Aries 1 model, circa approximately 1994-1995. The arm is indeed a 10-inch (you only measure the armtube) JMW metal unipivot arm. A very solid, substantial table in its day, and lots of them still running from ~30 years ago. And, I received this from a fellow trader kind enough to share his knowledge. One thing VPI didnt tell you about your particular Aries 1 is that in place of the stock platter that came with the table, yours has the platter from the VPI TNT 5.The Aries had a real good platter: 1.25; thick, comprised of a 7/8 thick bottom section made of aluminum (onto which was bonded a thin sheet of lead, covered in cork), with a 3/8 thick top layer of Delrin. The same platter came on the TNT 3 and 4.The TNT 5 has a great one: 1.5; thick, the bottom section 5/8 thick stainless steel (no lead sheet), with a 7/8 thick top Delrin layer. Thats the platter you have, and its the one most VPI aficionados consider the best platter VPI has ever made. Congratulations, it (and the Aries table) is a beauty! There is full inspection available to the buyer, but no returns for any reason, once it meets with your approval, if local pick-up. Must be picked up with 3 days if local pickup. I will make myself available within that timeframe. No exceptions. If shipped, I will only be able to do this within 5 days, vs my usual lightning shipping. No offers outside of ebay please. No opinions either, please. Just a nice clean sale to a pro preferably. Thanks in advance. Enjoy the music. Dance while you can, and every time you can. Please see my other GREAT items up for sale on ebay!!! On Dec-19-23 at 11:23:23 PST, seller added the following information: Please note: I was able to call ahead to UPS last night and arrange for the table to be packed immediately, first thing in the morning before they opened. I did not want anyone or anything around it. They unlocked the door for me at 8:15. It took the UPS rep a very very long time to pack this, as expected. The cost was more than quoted. It was $125. I was able to drop it down 15% using my AAA card, to $107. I do not mind absorbing this additional cost, even though it was far above what I was originally quoted by UPS. My only and sole concern it getting this to you, in two boxes, intact, safe, and just like it left here. I have posted the receipt from UPS today for the $107 I paid, just to reassure the buyer. The two boxes are ready to be shipped. Now, the question is,....to whom? LOL. Enjoy the music!!!

$90 JMW memorial tonearm alignment jig for VPI turntables, a must have VPI owners! Gently used condition, as new Works only with the VPI JMW-9 & JMW-9 Signature tonearms.The VPI Alignment Jig is a simple to use, accurate alignment jig for setting cartridge measurements. The VPI Alignment Jig addresses the three most important factors of alignment: Proper Offset, Tracking and Overhang. The VPI JMW alignment jig is a simple-to-use, accurate alignment jig for setting cartridge measurements. The JMW alignment jig addresses the three most important factors of alignment: Proper Offset, Tracking, and Overhang. It is a Denison jig using LÖFGREN B

Up for auction is a VPI JMW 10 3D printed tonearm in excellent condition. I went to a 12 for my main tonearm, so this one is now available. Heres what the auction comes with: 1. The tonearm with standard wiring and connector 2. Anti skate ring attachment and line 3. Your choice of a VPI 180 gram weight with thumb screw OR an unbranded 100 gram weight with Allen bolt (no thumb screw). Either weight comes with Soundsmith scale marker adhesive already attached. Check my feedback and bid with confidence. CONUS shipping is free. Thanks!On Dec-15-23 at 05:38:32 PST, seller added the following information: Up for auction is a VPI JWM 10 3D printed tonearm in excellent condition. I went to a 12 for my main tonearm, so this one is now available. Heres what the auction comes with: 1. The tonearm with standard wiring and connector 2. Anti skate ring attachment and line 3. Your choice of a VPI 180 gram weight with thumb screw OR an unbranded 100 gram weight with Allen bolt (no thumb screw). Either weight comes with Soundsmith scale marker adhesive already attached. Check my feedback and bid with confidence. CONUS shipping is free. Thanks!

This VPI Scoutmaster turntable is a must-have for any music enthusiast. With its sleek black design and belt drive feature, it offers high-quality audio playback. The JMW-9 Signature model adds a touch of sophistication with its fine-tuned components. Whether you're a vinyl collector or just starting out, this turntable is the perfect addition to your home audio setup. Its brand name speaks for itself and its features are sure to impress. Don't miss out on the opportunity to own this exceptional piece of equipment. This gorgeous turntable is in very good condition, non-smoking environment. It comes with many extras had to put the original feet on turntable to ship, comes with the two tone arms as seen in the pictures,a weight scale , anti-skate,upgraded feet, real nice cover that will be shipped separately this VPI scoutmaster will be a nice addition to your audio collection. it will come with no cartridge.I had the Ortofon M2Black and loved it. United States shipping only. thank you for looking.

Edwards Home Entertainment and Design, an appointed and displaying dealer for McIntosh, Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Gold Note, Marantz, Rose HiFi, AudioQuest, Nordost, as well as part of the Verified Premier Dealer Program on AudioGon, is offering this VPI Classic 3 table.This table is in fine shape, without issue - just had a new cartridge installed. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997 and is now an authorized dealer for McIntosh (displaying C2700, C22, C12000, MC462, MC275vi, MC1.25s, MEN220, MT-10, MT-5, MA12000, MA352, MA252, MPC500, MPC1500, MHA200, speakers and interconnect cabling), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3), Focal (displaying Scala EVO, Sopra3, Sopra2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5s2, S5, X3s2), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Fyne Audio (displaying F1-12, F1-8, 502SP, F700), HiFiROSE (displaying the RS150, RS250 and RS520), Parasound (displaying JC-1+, JC2BP, JC-5, JC-3+, and HINT6), Jeff Wells Audio (displaying Commander II and Innamorata II), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812, S/512, and T9/x), Perlisten (displaying the S7t and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), AudioQuest (displaying all power centers, 7000, 5000, 3000, Thunderbird, Black Beauty, Pegasus cabling), SolidSteel (displaying HyperSpike stands and amp stands), NEO Luxury Audio Racks (displaying the Quattron), Bossocontinuo (displaying the McRack) Reference. Visit the EHEADAudio com site in South San Francisco, CA for direct phone (begins with 925) / voice / text support. We are always looking to buy quality used gear. Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

Edwards Home Entertainment and Design, an appointed and displaying dealer for McIntosh, Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Gold Note, Marantz, Rose HiFi, AudioQuest, Nordost, as well as part of the Verified Premier Dealer Program on AudioGon, is offering this VPI Classic 3 table with a phenomenal cartridge.This table has the Lyra ATLAS cartridge, close to $12,000 alone. This table is piano black, comes with its cover and all packaging and boxes, BUT - if shipping is necessary, you must reach out to the numbers below. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997 and is now an authorized dealer for McIntosh (displaying C2700, C22, C12000, MC462, MC275vi, MC1.25s, MEN220, MT-10, MT-5, MA12000, MA352, MA252, MPC500, MPC1500, MHA200, speakers and interconnect cabling), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3), Focal (displaying Scala EVO, Sopra3, Sopra2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5s2, S5, X3s2), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Fyne Audio (displaying F1-12, F1-8, 502SP, F700), HiFiROSE (displaying the RS150, RS250 and RS520), Parasound (displaying JC-1+, JC2BP, JC-5, JC-3+, and HINT6), Jeff Wells Audio (displaying Commander II and Innamorata II), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812, S/512, and T9/x), Perlisten (displaying the S7t and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), AudioQuest (displaying all power centers, 7000, 5000, 3000, Thunderbird, Black Beauty, Pegasus cabling), SolidSteel (displaying HyperSpike stands and amp stands), NEO Luxury Audio Racks (displaying the Quattron), Bossocontinuo (displaying the McRack) Reference. Visit the EHEADAudio com site in South San Francisco, CA for direct phone (begins with 925) / voice / text support. We are always looking to buy quality used gear. Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

VPI Aries Scout turntable & JMW-9 tonearm.Legendary model from VPI that is still considered the best sounding machine in its price-range.Made in USA It is in excellent condition and looks and performs as new. Comes with extra bonus items: - Two custom record mats- Anti-vibration plates, that further improve the sound- Anti-static connection cable I have the original double-box and packaging materials, so safe shipping is guaranteed. Also included all manuals and brochures. Find this ad on the usaudiomart site (search by same description) for lower and tax-free pricing. You can check my 100% positive feedback there “Rather, this is a flat-out, unconditional, “Holy Mother of Crap, I can’t believe how good this thing is” recommendation. It’s hard to imagine another way of spending $****.** that will add this much to your system.” – Art Dudley, Stereophile Magazine Description: Two-speed, belt-driven turntable with AC synchronous motor, acrylic record platter, and Delrin reflex record clamp; aluminum-alloy unipivot tonearm, height-adjustable, with interchangeable armwands. Wow & flutter: <0.02%. Rumble: below -80dB. Speed accuracy: within 0.1%. Dustcover: none. Spindle-pivot distance: 222mm. Downforce calibration: none. Antiskating: none.Dimensions: 19 W by ca 4.5 H by 14 D (without dustcover). Weight: 37 lbs.Finish: Black semigloss enamel (turntable), textured aluminum (tonearm). The Turntable:1.25? thick premium textured vinyl covered MDF bonded to a 12 gauge steel plate.Machined 1 3/8? thick 6061 acrylic platter.Platter rotates on an oil bath bearing and fitted to shaft with a #2 Jacob’s Taper for a concentric rigidly mounted coupling.The bearing has a PEEK thrust disc and machined graphite impregnated brass bushings using a Thompson Engineering 60 Rockwell case hardened shaft.300 RPM AC synchronous motor is contained in a separate steel housing and drives the platter with smooth, quiet operation.Includes a screw down record clamp that eliminates warpsCartridge not includedTechnical SpecificationWow and Flutter: .08% WRMSSpeed Accuracy: .08%Rumble: >78 db DownFootprint: 19 ½” x 13 ¾”Overall Dimensions: 21?” x 15¾” 54lbs packing weightTechRadar: Of VPIs seven-strong range of turntables, the Scout is the New Jersey-based manufacturers most affordable offering: with a price of under £1,600, it must be the least expensive US made turntable on the market.But, what it lacks in price, the Scout makes up for in size, being easily the widest turntable in the group, although it just about fits on a standard width equipment support.Furnished with a solid plinth design with a separate freestanding motor block, the Scouts only means of keeping stand-bound resonance at bay are Sorbothane mountings above each of the conical feet. The latter are tipped with a ball, rather than a spike, that will be a lot kinder to supporting surfaces.The plinth is composed of MDF atop a steel plate, while the platter is a 34mm slab of acrylic that sits on an inverted bearing with a Teflon thrust pad and a case-hardened shaft.The motor sits in a steel box that accepts a kettle lead, but cleverly hides this junction underneath the turntable. What you do see is a switch sticking out that turns it on and off. Drive is via a round section peripheral belt and speed change is a matter of flipping the belt onto the lower pulley for 45rpmThe JMW9 tonearm is a unipivot design thats beautifully finished but a pain to set-up, thanks to the wobbly nature of the genre. It has a sharp tip that acts as the bearing point and a rather ineffectual arm clamp that does little to hold it in place.The Scout does most things better than average and its good quality finish and build combine with this to make for an attractive package. The unipivot JMW9 is easily the most impressively built tonearm in this group and, for those who like using alternative cartridges, it offers the easiest means to swap the things over if you buy a second arm wand.

VP Ij MW10 memorial tone arm in excellent condition with alignment jig. I bought this from a member here. Never even mounted it and had decided to go in another direction. Model s*** my loss, your game. Free shipping in the continental united states only. Also listed on Facebook groups, US Audiomart and local. Look at the photos, more photos available just ask. No returns.

This VPI Scout turntable comes with the JMW 9 Memorial Tonearm, Audio Technica AT-VM95SH MM cartridge and stylus. Belt drive - 45RPM or 33.3RPM. Table is used - rated good condition due to uncertain age. Table includes dust cover and accessories as shown. Ships in original box. Dust cover ships separately.

?ª˜¨¨?ª˜¨¨¨¨˜ª¤.¸*•.¸*•¸? ? Super eBayer ??¸•*¸.•*´¸.¤ª˜¨¨¨¨˜ª?¨¨˜ª? I do provide excellent service to every buyer. Please see my feedback before you bid, and see that everyone is happy with my prices, my product .... and my service. Good Day! I must apologize for changing this auction to local pickup only. I am doing this primarily due to one jerk. So, I am NOT shipping this. Id rather sell it really cheap to someone nice thats local, and they can see it for themselves, and not play games like swapping parts. I just dropped the price to a honey, lets go for a drive price. This was NOT my personal item. I did not use it, test it, or know any more about it than I have pictured or told by VPI or other VPI table owners. You are bidding on what you see pictured/ I wish for the buyer to see for himself that received what is pictured, and the condition it is in, is as described. I cannot offer any more information than that. All buyers please bid accordingly, if interested. I have done my very best to present this item honestly and accurately. This IS for local pick-up only in Locust Grove, VA 22508. Next, no nonsense please. Im too old. Getting older is problem enough for me. My understanding is that this is one of the most sought after and rare ever sold by VPI. Please read the following: I bought out an entire recording studio, lock stock and barrel for a tidy sum. Among the items was this table. Comes with manuals and vintage warranty registrations. I also contacted Jim at VPI, and here is what he told me. Its definitely an Aries 1 model, circa approximately 1994-1995. The arm is indeed a 10-inch (you only measure the armtube) JMW metal unipivot arm. A very solid, substantial table in its day, and lots of them still running from ~30 years ago. And, I received this from a fellow trader kind enough to share his knowledge. One thing VPI didnt tell you about your particular Aries 1 is that in place of the stock platter that came with the table, yours has the platter from the VPI TNT 5.The Aries had a real good platter: 1.25; thick, comprised of a 7/8 thick bottom section made of aluminum (onto which was bonded a thin sheet of lead, covered in cork), with a 3/8 thick top layer of Delrin. The same platter came on the TNT 3 and 4.The TNT 5 has a great one: 1.5; thick, the bottom section 5/8 thick stainless steel (no lead sheet), with a 7/8 thick top Delrin layer. Thats the platter you have, and its the one most VPI aficionados consider the best platter VPI has ever made. Congratulations, it (and the Aries table) is a beauty! There is full inspection available to the buyer, but no returns for any reason, once it meets with your approval. Must be picked up with 3 days, local pickup. I will make myself available within that timeframe. No exceptions. No offers outside of ebay please. Thanks in advance. Enjoy the music. Dance while you can, and every time you can. Please see my other GREAT items up for sale on ebay!!!

Up for auction is my recently serviced (by George Meyer AV), upgraded VPI Scout turntable. The turntable was significantly upgraded with the JMW Memorial 10.5i Tonearm and the HRX/Scoutmaster 2 platter and inverted bearing. This is the perfect table for those who want more than the stock Scout or Prime. It is boxed up and ready to ship. The JMW 10.5i arm has the VTA on the fly tower, that you dont get on any table below the $5K VPI Prime 21. It is wired internally with Nordost Valhalla wiring from the cartridge pins all the way through to the cable junction box, with an additional 2.5 grams effective mass for greater cartridge compatibility (including lighter, low compliance carts), variable pivot fluid damping, and mechanical anti-skate control. please note, I used the twisted wire anti skate method recommend by VPI an no longer have the rubber anti-skate weights. Also included is the Soundsmith counterintuitive, VPI alignment jig, and Ginko cover (although the cover is modified by me to fit the much larger arm. No cartridge is included with the sale. However, I would recommend the Ortofon Quintent Black. This is a heavy table, and will come in 2 boxes (1 for the table the second for the cover) No returns or warranty implied.

ITEM DESCRIPTION: For sale is a VPI JMW 10 unipivot metal armwand. (Tonearm Only: Turntable and Cartridge not available). Compatible not only with VPI but with most hifi turntables as well. Cabling tested for functionality before sale. Tonearm is in a very good condition, please review all photographs provided for all details.  The quality of the workmanship of the JMW 10 tonearm is as just superb. It’s setup makes it very simple to adjust the VTA for records of different thickness, a very nice touch. Item will be well packed for safe arrival. ------------------------------------------------- PHYSICAL CONDITION: Used but in a great shape. Check pictures for cosmetic condition -------------------------------------------------------- SHIPPING: Shipping to USA via USPS. Local pick up is welcome with no charge.  ------------------------------------------------- RETURN: Item has been described to the best of my knowledge and please ask questions before bidding. Due to nature of used equipment, item is being sold AS IS, NO RETURN. ------------------------------------------------- PAYMENT: PayPal or cash for local pick up. Pay within 3 days after end of auction. ------------------------------------------------- OTHERS: Any dispute can be resolved with friendly message exchange so please contact me first before involving eBay. 

Also includes Octave EQ.2 Phono Preamplifier

PREOWNED - $2800 LIST! - FULLY TESTED - INCLUDES ORIGINAL BOX/PACKING, MANUAL, 20LBS/12 PLATTER, 300RPM MOTOR UPGRADE, CONE FEET, CLAMP, POWER CABLE, ALIGNMENT JIG, 2 DRIVE BELTS, ANTI-SKATE WEIGHT, MAT, COUNTER INTUITIVE

?ª˜¨¨?ª˜¨¨¨¨˜ª¤.¸*•.¸*•¸? ? Super eBayer ??¸•*¸.•*´¸.¤ª˜¨¨¨¨˜ª?¨¨˜ª? I do provide excellent service to every buyer. Please see my feedback before you bid, and see that everyone is happy with my prices, my product .... and my service. Good Day Thanks for looking. In that this item is as costly as it is, I must lay down some ground rules. This is for local pick-up only in Locust Grove, VA 22508. No, I will not and cannot ship it, at least at this point. Next, no nonsense please. Im too old. Dont need it. Getting old is problem enough for me. My understanding is that this is one of the most sought after and rare ever sold by VPI. It is worth the drive. I have many offers if I will ship, and even more than I am asking. I cannot risk it. Please read the following: I bought out an entire recording studio, lock stock and barrel for a tidy sum. Among the items was this table. Comes with manuals and vintage warranty registrations. I also contacted Jim at VPI, and here is what he told me. Its definitely an Aries 1 model, circa approximately 1994-1995. The arm is indeed a 10-inch (you only measure the armtube) JMW metal unipivot arm. A very solid, substantial table in its day, and lots of them still running from ~30 years ago. And, I received this from a fellow trader kind enough to share his knowledge. One thing VPI didnt tell you about your particular Aries 1 is that in place of the stock platter that came with the table, yours has the platter from the VPI TNT 5.The Aries had a real good platter: 1.25; thick, comprised of a 7/8 thick bottom section made of aluminum (onto which was bonded a thin sheet of lead, covered in cork), with a 3/8 thick top layer of Delrin. The same platter came on the TNT 3 and 4.The TNT 5 has a great one: 1.5; thick, the bottom section 5/8 thick stainless steel (no lead sheet), with a 7/8 thick top Delrin layer. Thats the platter you have, and its the one most VPI aficionados consider the best platter VPI has ever made. Congratulations, it (and the Aries table) is a beauty! There is full inspection available to the buyer, but no returns for any reason, once it meets with your approval. Must be picked up with 3 days. I will make myself available for your inspection within that timeframe. No exceptions. No offers outside of ebay please. Thanks in advance. Enjoy the music. Dance while you can, and every time you can. Please see my other GREAT items up for sale on ebay!!!

Also includes Octave EQ.2 Phono Preamplifier

?ª˜¨¨?ª˜¨¨¨¨˜ª¤.¸*•.¸*•¸? ? Super eBayer ??¸•*¸.•*´¸.¤ª˜¨¨¨¨˜ª?¨¨˜ª? I do provide excellent service to every buyer. Please see my feedback before you bid, and see that everyone is happy with my prices, my product .... and my service. Good Day Thanks for looking. In that this item is as costly as it is, I must lay down some ground rules. This is for local pick-up only in Locust Grove, VA 22508. No, I will not and cannot ship it, at least at this point. Next, no nonsense please. Im too old. Dont need it. Getting old is problem enough for me. This is a cash upon your absolute satisfaction sale and do not pay me until you are gloriously happy, pulling out of our driveway. Please read the following: I bought out an entire recording studio, lock stock and barrel for a tidy sum. Among the items was this table. Comes with manuals and vintage warranty registrations. I listed it previously incorrectly, so I opened up the box to take appropriate pictures. I also contacted Jim at VPI, and here is what he told me. Its definitely an Aries 1 model, circa approximately 1994-1995. The arm is indeed a 10-inch (you only measure the armtube) JMW metal unipivot arm. A very solid, substantial table in its day, and lots of them still running from ~30 years ago. And, I received this from a fellow trader kind enough to share his knowledge. One thing VPI didnt tell you about your particular Aries 1 is that in place of the stock platter that came with the table, yours has the platter from the VPI TNT 5.The Aries had a real good platter: 1.25; thick, comprised of a 7/8 thick bottom section made of aluminum (onto which was bonded a thin sheet of lead, covered in cork), with a 3/8 thick top layer of Delrin. The same platter came on the TNT 3 and 4.The TNT 5 has a great one: 1.5; thick, the bottom section 5/8 thick stainless steel (no lead sheet), with a 7/8 thick top Delrin layer. Thats the platter you have, and its the one most VPI aficionados consider the best platter VPI has ever made. Congratulations, it (and the Aries table) is a beauty! There is full inspection available to the buyer, but no returns for any reason, once it meets with your approval. Buyer expected to pay local sales tax as well, so please come prepared, and do not say that this is all you brought. Must be picked up with 3 days. Thanks in advance. Enjoy the music. Dance while you can, and every time you can. Please see my other GREAT items up for sale on ebay!!!

Edwards Home Entertainment and Design, an appointed and displaying dealer for McIntosh, Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Gold Note, Marantz, Rose HiFi, AudioQuest, Nordost, as well as part of the Verified Premier Dealer Program on AudioGon, is offering this VPI Classic 3 table with a phenomenal cartridge.This table has the Lyra ATLAS cartridge, close to $12,000 alone. This table is piano black, comes with its cover and all packaging and boxes, BUT - if shipping is necessary, you must reach out to the numbers below. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997 and is now an authorized dealer for McIntosh (displaying C2700, C22, C12000, MC462, MC275vi, MC1.25s, MEN220, MT-10, MT-5, MA12000, MA352, MA252, MPC500, MPC1500, MHA200, speakers and interconnect cabling), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3), Focal (displaying Scala EVO, Sopra3, Sopra2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5s2, S5, X3s2), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Fyne Audio (displaying F1-12, F1-8, 502SP, F700), HiFiROSE (displaying the RS150, RS250 and RS520), Parasound (displaying JC-1+, JC2BP, JC-5, JC-3+, and HINT6), Jeff Wells Audio (displaying Commander II and Innamorata II), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812, S/512, and T9/x), Perlisten (displaying the S7t and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), AudioQuest (displaying all power centers, 7000, 5000, 3000, Thunderbird, Black Beauty, Pegasus cabling), SolidSteel (displaying HyperSpike stands and amp stands), NEO Luxury Audio Racks (displaying the Quattron), Bossocontinuo (displaying the McRack) Reference. Visit the EHEADAudio com site in South San Francisco, CA for direct phone (begins with 925) / voice / text support. We are always looking to buy quality used gear. Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

VPI JMW-10.5i Tonearm(Tonearm Only- Turntable and Cartridge not available) 10.5 Metal Tonearm Compatible with most hifi turntables Cabling tested for functionality before sale

This is a VPI JMW Memorial alignment jig. This came from a high end estate with a large quantity of turntables, all of which had already been liquidated by the time this jig turned up in a cabinet with other audio accessories, therefore I cant tell you specifically if this is for use with the JMW-9, JMW-10 or JMW-12 tonearms so please review the dimensions in the photo to determine if this is right for you. Im almost certain that the tonearm was on a model called the Classic, if that helps any. I measured from the white dot in the center of the grid which is where the stylus will rest, to the V groove of the fork which will be the base of the pivot point where the tonearm will be placed atop and it measured 10.15. The answer seems like it should be obvious to me but I dont want to make any incorrect claims. At any rate, its straight and true and in excellent preowned condition from a non-smoking environment and itll go home with the highest bidder so dont miss it! Ive taken a number of pictures and Ive enabled the scroll over zoom function so you can get an even closer look. So please do have a good look and if this looks right for you, be sure to place your bid TODAY for your chance to take it home! Payment due within 24 hours of auctions end, please. The sooner you pay, the sooner youll receive them. I ship same day or following business day, depending on when the auction ends, so youll get it fast! And as always, local pickup at my home is welcome!

?ª˜¨¨?ª˜¨¨¨¨˜ª¤.¸*•.¸*•¸? ? Super eBayer ??¸•*¸.•*´¸.¤ª˜¨¨¨¨˜ª?¨¨˜ª? I do provide excellent service to every buyer. Please see my feedback before you bid, and see that everyone is happy with my prices, my product .... and my service. Good Day Thanks for looking. In that this item is as costly as it is, I must lay down some ground rules. This is for local pick-up only in Locust Grove, VA 22508. No, I will not and cannot ship it, at least at this point. Next, no nonsense please. Im too old. Dont need it. Getting old is problem enough for me. This is a cash upon your absolute satisfaction sale and do not pay me until you are gloriously happy, pulling out of our driveway. Please read the following: I bought out an entire recording studio, lock stock and barrel for a tidy sum. Among the items was this table. Comes with manuals and vintage warranty registrations. I listed it previously incorrectly, so I opened up the box to take appropriate pictures. I also contacted Jim at VPI, and here is what he told me. Its definitely an Aries 1 model, circa approximately 1994-1995. The arm is indeed a 10-inch (you only measure the armtube) JMW metal unipivot arm. A very solid, substantial table in its day, and lots of them still running from ~30 years ago. And, I received this from a fellow trader kind enough to share his knowledge. One thing VPI didnt tell you about your particular Aries 1 is that in place of the stock platter that came with the table, yours has the platter from the VPI TNT 5.The Aries had a real good platter: 1.25; thick, comprised of a 7/8 thick bottom section made of aluminum (onto which was bonded a thin sheet of lead, covered in cork), with a 3/8 thick top layer of Delrin. The same platter came on the TNT 3 and 4.The TNT 5 has a great one: 1.5; thick, the bottom section 5/8 thick stainless steel (no lead sheet), with a 7/8 thick top Delrin layer. Thats the platter you have, and its the one most VPI aficionados consider the best platter VPI has ever made. Congratulations, it (and the Aries table) is a beauty! There is full inspection available to the buyer, but no returns for any reason, once it meets with your approval. Buyer expected to pay local sales tax as well, so please come prepared, and do not say that this is all you brought. Must be picked up with 3 days. Thanks in advance. Enjoy the music. Dance while you can, and every time you can. Please see my other GREAT items up for sale on ebay!!!

Edwards Home Entertainment and Design is offering this VPI Classic 3 table with a phenomenal cartridge. This table has the Lyra ATLAS cartridge, close to $12,000 alone. This table is piano black, comes with its cover and all packaging and boxes, BUT - if shipping is necessary, you must reach out to the numbers below. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD Audio, located in South San Francisco, CA) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997. In 2020 I became a dealer for several manufacturers - to add to the plethora of great quality, highly sought after, preowned gear.  Now an authorized dealer for Parasound (displaying JC-1+, JC2BP, HINT 6, JC-5, JC-3+), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S2 Signature Midnight Blue, 705S2 Signature), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Focal (displaying Scala EVO, Sopra3, Sopra 2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5, S5), Fyne Audio (displaying F1-12, 502SP, F700), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying S/812 and S/512), Lumin (displaying T2, D2, and U1 mini), Nordost (displaying Norse and Leif series, with demo cases for in home trials), SolidSteel (displaying HyperSpike and S3 walnut), Finite Element (displaying Pagode).   EHEAD Audio is always looking to buy quality used gear.  Do reach out and we can discuss single to entire systems, to even life long collections that you may be looking to sell.  Every piece of equipment EHEAD Audio provides, operates as expected as each and every piece is inspected, tested, and listened to prior to sale.  After all, I love music as you do and learning what pieces of gear do well and match with others is part of the invaluable experience I provide, and have since 1997.   Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear.  Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country.  If you are interested in our gear, please reach out and we can figure out a shipping solution that will work.  EhEAD Audio can facilitate and complete all necessary documentation for the export of your gear purchased from us. Our shop is in South San Francisco - stop by and put your eyes and ears to work! California residents or any shipment within California must pay 9.75% sales tax.