TESTED ON CALIBRATED (IN 2021) TV-7a/u BY DAN NELSON NO SHORTS OR LEAKS DETECTED TELEFUNKEN WEST GERMANY MADE, BRANDED FOR FISHER TESTED AT = 22-27 MIN GOOD RESULT = 32-32 LOWER TESTING, SHOULD BE GOOD IN MANY CIRCUITS, BUT NOTE IT IS BELOW RECOMMENDED MINIMUM

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va=250V Vg=-8,5V & (-5V) Ia=10,5mA & (20mA) HICKOK TV7D/U EV7-6080 B24 B min=56 (65%) (100%=93)EV2-1030 B24 B min=56 (65%) (100%=93) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) ue MAZDA Long flat plates, ring getter telefunken bottom code 10,3/10,4 (20,4/20,5) 110/110 EUROPE COUNTRIES --> ASK FOR MONDIAL RELAY SERVICE (LESS EXPENSIVE)

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) wr MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,5mA/1,2mA (3,7/3,2) 55/52 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) ue MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,6mA/1,5mA (3,9/3,7) 57/55 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) yf MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,3mA/1,4mA (3,4/3,5) 53/54 ue MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,4mA/1,3mA (3,6/3,6) 54/53 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) ca MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 0,9mA/0,9mA (2,9/2,7) 49/48 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 78.5/62 PC 13.693/62 PC 17.4 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 92/62 PC 16.2 98/62 PC 18.2 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 72/62 PC 11.9 70/62 PC 11.5 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 91.5/62 PC 17.688/62 PC 16.5 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 42.7/32 PC 4.745.7/32 PC 5 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 1. 45/32 PC 4.944.4/32 PC 4.9 2. 45.9/32 PC 5 49.2/32 PC 5.4 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 1. 43/32 PC 4.8 44.7/32 PC 4.9 2. 47/32 PC 5.2 44.8/32 PC 4.9 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

NOS NIB Mullard 5AR4 GZ34 rectifier tube branded Telefunken Made in Great Britian in 1965 and of vintage production. Excellent testing tube. Tests as new. Close-matched sections. Date code: f32 B5A1. Very good gettering. Top, dual D-getters. Clean glass and pins. Tight bases & no cracks. No large chunks inside. Keyway intact. Printing is good. Tested on a calibrated TV-7D and at real operating voltages on an Amplitrex AT1000. Tubes operated 10 min ea. before tests to ensure stability. TV7 test results: Tube #1: 60/60. Minimum good on TV-7D: 40. Typical new 5AR4’s test 55 to 60. Amplitrex AT1000 test results: Tube #1: Forward drop: 4/4 v. Reverse drop: 416/416 v. Nominal 5AR4 forward voltage drop @100mA: 9/9 volts. In conclusion- Test as an excellent tube. As new. An excellent addition to anyones collection. Money back guarantee you will not be disappointed. All items are 100% guaranteed to arrive as represented for 30 days upon arrival. We offer a full refund if you are not satisfied. Weve been selling vintage electronics since 1999 with perfect ebay feedback and many happy, satisfied customers. All items professionally packed to arrive safely with no extra handling costs. Our mission is to offer quality-tested tubes to make you happy with your purchase. Terms & Conditions: Payment must be received within 3 days of sale date. Items described to the best of my ability. If you have questions, please contact me BEFORE purchasing. Thank you!

5 Ef800 Early Telefunken Microphone Tubes Tv7d/u Tested Strong. They test 55/38 min 56/38 min 56/38 min 57/38 min 55/38 min

For sale: 2pcs SE output audio transformers BV 7105/3 Siemens for EL12 from 30s All the photos I show you, are taken by myself and belong to me. Shipping to Japan, Hong Kong costs $50 including fees.For buyers from the European, shipping costs - $20 including fees. Taiwan buyers: delivery takes more than a month...if you dont wait patiently for the item, please dont bid. Thank you for your understanding. I currently sell over 17 items, check out my other items for sale.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% same dates 1.95/62 PC 18100/62 PC 19.9 2.94/62 PC 18.593/62 PC 17.3 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 101.5/62 PC 19.4 96/62 PC 18.4 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

Tested on a fully restored TV7-DU, by Dan Nelson, pictures of evidence for this included in the listing. It was restored and calibrated on October 21st 2021. Tubes are tested for shorts. PC= Plate Current DC= Date Code Please note, TV7 data minimum is equal to 60%. For example, (insert model number here) min value 60. If the tube tests at minimum 60, that is equal to 60%. The number over (/) is the minimum test data result as described in the TV7 DU tube testing manual. So 60/ (min) 60 = 60% 103/62 PC 20.6 96/62 PC 19.4 I mark all my tubes, so please dont waste your time seeking to send me back your old dead tubes. All testers read differently. I have sought to have my tester as accurate as possible. I will not be giving partial refunds because you have received different test result. All tubes will be shipped well, an example of how I pack is pictured in the listing. (obviously these tubes are not included) I wont be lying on a customs form I combine shipping. If the tubes are of significant value, the postage will be extra due to insurance.

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va=250V Vg=-8,5V & (-5V) Ia=10,5mA & (20mA) HICKOK TV7D/U EV7-6080 B24 B min=56 (65%) (100%=93)EV2-1030 B24 B min=56 (65%) (100%=93) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) ue MAZDA Long flat plates, ring getter telefunken bottom code 10,3/10,4 (20,4/20,5) 110/110 EUROPE COUNTRIES --> ASK FOR MONDIAL RELAY SERVICE (LESS EXPENSIVE)

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) yf MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,3mA/1,4mA (3,4/3,5) 53/54 ue MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,4mA/1,3mA (3,6/3,6) 54/53 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) ca MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 0,9mA/0,9mA (2,9/2,7) 49/48 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) ue MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,6mA/1,5mA (3,9/3,7) 57/55 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...

TESTS CONDITIONS (datasheet) DUOVAC RADIOELEC Va = 250V Vg=-2V Ia=1,2mA (Va=250V Vg=-1V Ia=3,2mA) HICKOK TV7D/U EV7-6080 B12 B min=32 (65%) EV2-1030 B12 B min=32 (65%) Please note that HICKOK is not a laboratory tester, though it is very well calibrated...HERE is how I calibrated mine following manual services specifications. I calibrated it to respect the low of the scale for filament... High voltage on filament would damage it...but gives higher values...0.6 (065-0.72) -->0.65V ; 1.1 (1.06-1.16) -->1.14V ; 1.5 (1.26-1.42) -->1.30V ; 2.0 (1.90-2.10) -->1.95V ; 2.5 (2.56-2.88) -->2.77V ; 3.0 (3.25-3.60) -->3.25V ; 4.3 (4.30-4.75) -->4.55V ; 5.0 (5.15-5.68) -->5.49V ; 6.3 (6.20-6.80) -->6.47V ; 7.5 (7.32-8.10) -->7.45V ; 10 (9.60-10.80) -->10.03V ; 12.6 (12.1-13.3) -->12.25V ; 20 (19.0-21.0) -->20.50V ; 25 (25.3-28.0) -->27.65V ; 35 (35.2-39.0) -->38.09V ; 50 (51.5-57.0) -->52.80V ; 75 (74.0-82.0) -->74.82V ; 117 (115-127) -->116.5VIf needed, i can share all other tests calibrations I get (129.5V/130V +o-3V ; 41.35V/40V +o-2V ; 4.21V/4V +o-1V ; 56.5V /56V....) wr MAZDA TELEFUNKEN LONG SMOTH PLATES <> BOTTOM 1,5mA/1,2mA (3,7/3,2) 55/52 ! NEW OLD STOCK ! CHECK ALL THE LIST TO BUY OTHER REFERENCES AND COMBINE SHIPPING PLEASE CONTACT ME BEFORE BUYING TO CHECK THE BEST OPTION FOR THE SHIPPING COSTSTUBES ARE QUITE FRAGILE, SO YOU SHOULD PAY A BIT MORE FOR A SAFE PACKAGE THAN A BUBBLE LETTER. I DECLINE ANY RESPONSABILITIES IF YOU CHOOSE LETTER AND YOUR ITEMS ARE DAMAGED DURING TRANSPORT...