Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

TECHNICS VINTAGE SL-D2 3300 3200 5200 TURNTABLE Tone Arm Rest Good condition.

Technics SL-3300 3200 D2 Turntable Counterweight Counter Weight Good condition.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Description Description&Previewshipping&policyDescription:If youre like me there is nothing worse than having to lift off your dust-cover when you want to use your turntable. I became so disgusted I decided to do something about it. These professionally manufactured tabs are made out of machined aluminum and leather tumbled for a great smooth feel and appearance. They fit nice and snug into the pockets of virtually any Technics table that come with those nasty tabs (check the measurements) and work perfectly. Very professional appearance. #8 machine screws, nuts and washers included with each tab purchased. These work much better on the outside of the cover instead of the inside. Ive always had problems with the cover not completely closing when you place the tabs on the inside. For the SL-D2 type tables you line up the base even with the dust-cover (see photo). For the Q200 type tables with the shorter cover you will want to line up the actual small tab with the bottom of the cover. I use #8 machine screws (included) which work perfectly. If you want to drill a slightly larger hole in your dust-cover this will give you some wiggle room in case youre slightly off with your drilling. To grind off your broken tab you want to use a (or equivalent) and take your time. Make sure to wear safety goggles and remove as much as the old tab as possible so the back of the cover is nice and flush. Once that is accomplished you want to line up the new tab in the proper position on the cover. I use painters tape which doesnt leave residue and is plenty strong enough. Check to make sure the new tab is in the proper position by placing the cover with the tab (held by tape) in your tables hinge. This is easier if youre replacing just one tab but if you need both just take your time, youll be able to see the area where the old tab was by the marks. package include: 1*set Preview: Thank you for your purchaseProblems? You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions: Shipping ? We will arrange shipping for you within 24 Hours after payment cleared except the holidays. ? We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost. Payments We accepts Paypal only If you have any questions about the payment,please contact us through eBay message. Import Duties In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.Terms & Conditions By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding. All pictures are for illustration purpose only and Colours may vary slightly. Our store obeys all eBay Rules and Policies.Returns Policy To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it. Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging. All shipping and handing charges are non-refundable Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items. Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.

Vintage Technics SL-3200 Direct Drive Automatic Record Player Vintage Technics, Model SL-3200, Direct Driver, Automatic Record Player, in working order, great used condition, with dust cover/lid, plays 33 & 45, semi automatic, clean, with Technics 270c needle, silver finish, 50-60hz. Size: H: 12.5cm, W: 43cm, D: 36cm - 37.5cm Important Information Please Read Prior to Purchase This item is sold ‘as is’ in accordance with Ebay Regulations. Payments Payments can be made via Paypal or Cash if collecting, cash is preferred where possible. Item Descriptions Please ensure it meets with your requirements, sizes are provided on each listing, we welcome questions from anyone who may be unsure about any part of the description, or who may require clarification on materials, colours, makes, models, etc. All descriptions are as accurate as possible from the information to hand. Some of our items come from home/office clearances where background or make/model information may be missing or limited, your questions will ensure buyer’s satisfaction is achieved. Items are cleaned prior to listing where required, and any Electricals are PAT tested, (portable appliance testing), and details logged as required, some stepped power plugs do not require testing due to their low voltage. The PAT test will confirm the item is in a good, safe order at the time of the test. Cookers cannot be PAT tested, due to the nature of the cable, and we recommend buyers ensure a qualified electrician installs the item. Fridges, Freezers and Washing Machines are tested prior to listing, which includes ensuring ice forms where required, items cool, and washing/spin cycles are tested. Returns Policy Returns are accepted under the ebay rules and Kent Re-Users own policy, the buyer remains responsible for any costs incurred in returning the item unless faulty or damaged in transit. If collected or delivered, please ensure you are happy with the item prior to either leaving with the item, or accepting it. We do not provide discounts or refunds without returning items. Items purchased may be returned within 30 days of the item being collected or delivered. A full refund (including any postage costs, where applicable) will be offered providing the item is returned in the same condition as purchased, including any packaging, boxes, manuals, keys, power leads or any other item associated with the item in question shown or detailed in the listing. If you are unhappy with any purchase, please contact us as soon as possible by Ebay message. Delivery & Postage/Courier Costs Items with Royal Mail or Courier delivery charges quoted, or stating ‘free delivery’, will take precedence over our own delivery charges. If the item is too large to post via Royal Mail, or courier, we do offer delivery as follows. We can deliver items that have a sale price of £40.00 or more, or a combination of items with a total sale value of £40.00 or more, within the Kent area as follows: Standard Delivery £25.00. Large/Heavy items requiring three persons lift, i.e Piano’s, Safe’s etc £40.00 Please contact us if you require a delivery outside of the Kent area, our vehicles do not meet the Ultra Low Emissions Zones requirements, surcharges/tolls will be payable in these Zones and will need to be added to the delivery charge. We unfortunately no longer deliver to London. Deliveries are only made during working hours at a mutually convenient date/time. Please note some long distance destinations may require an overnight accommodation charge, where health and safety would require a sleep break. We are also happy for customers to arrange their own courier to collect, please ensure our contact details are passed onto the courier to enable collection to be arranged. Most courier companies will only accept an item if it is boxed or packaged, unless a private man & van courier, please contact us first to ensure the item in question can be packaged. We are unable to accept any liability for items damaged or lost once collected by a courier arranged by the purchaser. Items sent via Royal Mail or Hermes/UK Mail will be packaged to the best of our ability using bubble wrap/plastic covering/padded envelopes where appropriate. Liability for loss in transit cannot be accepted unless written notification (email/message is sufficient), is received within 7 days of despatch. All items are despatched within 3 working days or sooner of the item ending or payment being received. Please notify us of any damage in transit within 48 hours of receipt. The General Manager’s decision with regard to providing refunds is final and every effort will be made to ensure customer satisfaction within the above parameters. Collections Collections for successful bidders are available Monday and Thursday 9:00am – 16.30pm excluding Bank Holidays, which is a Tuesday after the Bank Holiday. We aim to arrange collections around deliveries and house/office clearances, which we undertake on Tuesday’s, Wednesday’s & Friday’s. We will try to be as flexible as possible, but cannot arrange collections on Sunday’s or Bank Holiday’s, and are unable to arrange evening collections. If you wish to collect on one of our days allocated for clearances/deliveries, please contact us and we can arrange a collection at a specific time during the day where possible. Please refrain from purchasing items and then messaging to advise you can only collect on an evening or a Sunday. We will try to be as flexible as possible but unfortunately, it is not cost effective to open the office outside of working hours when the cost will far outweigh the value of the item purchased. It is always best to contact us prior to purchase if you are unable to collect during our working hours. All items must be collected within two weeks of purchase, unless a later date has been agreed by Management prior to purchase. We are not able to be a storage facility, space is limited. Collections Available: Monday 9:00am-16:30pm (Closed Bank Holidays, Open Tuesday after Bank Holiday for collections) Tuesday Reserved for House Clearances Wednesday Reserved for House Clearances Thursday 9:00am-16:30pm Friday Reserved for House Clearances Saturday 9:00am-11:30am (by appointment, please contact us to arrange) Sunday Closed If you make a mistake with a purchase or bid and change your mind prior to the item ending, or after the item has ended, please contact us as soon as possible to make arrangements for the purchase or bid to be cancelled via Ebay. It is an easy process and will not affect your feedback in any way. Many Thanks for taking the time to look at our items. Kent Re-Users Revised 31/1/23