Recommended Amplifier Power: 20 to 150 watt RMS Peak Power Handling: 175 watt Nominal Impedance: 8 ? Sensitivity (2,83 volts at 1m): 91 dB Distortion: less than 0,75% (52 Hz - 25 kHz) Phase Response: System behaves substantially as a frequency-independent time delay Dispersion: 90 degrees conical Crossover Frequency: 2 kHz Crossover Type: 2nd order LF, 1st order HF Hard-Wired, low-loss, Positive acoustic polarity Frequency Response (±3 dB): 52 Hz - 25 kHz Drive Unit Type: 6,5 inch, 1667 Dual Concentric Cabinet Internal Volume: 10 litres Cabinet Material: 30,6 mm MDF front baffle; 15 mm high density particle board lined with TF-1 acoustic wadding Cabinet Finish: High quality vinyl finish. Velti shadow grey soft-texture finish baffle Grille: Single piece, black acoustically transparent material over a rigid frame Dimensions (H x W x D): 345 x 230 x 223 mm (13,6 x 9,1 x 8,8)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THE SUPER TWEETER IS SLIGHTLY DIMPLED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. I ADDED 4 WALL CLAMPS TO THE FRAMEWORK THAT ARE NOT SHOWN IN THE PICTURES SO ITS STILL MISSING 4 MORE WALL CLAMPS. THIS ONE HAS HAD SCREWS DRIVEN THROUGH THE FRAME TO INSTALL BEFORE, THERE HAS BEEN A SMALL HOLE REPAIRED IN THE DUAL CONCENTRIC DRIVER, 4 OF THE WALL CLAMPS ARE MISSING, THE SUPER TWEETER IS DAMAGED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS HAD SCREWS DRIVEN THROUGH THE FRAME TO INSTALL BEFORE, THERE HAS BEEN A SMALL HOLE REPAIRED IN THE DUAL CONCENTRIC DRIVER, THE WALL CLAMPS ARE MISSING, THE SUPER TWEETER IS DAMAGED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THE SUPER TWEETER IS SLIGHTLY DIMPLED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

Tannoy Dual Concentric Drive Unit Driver LF. This is a damaged 6 Low-Frequency driver, which was damaged in shipping. The basket is slightly askew, and the voice-coil got stuck out of the gap, presumably when the box was dropped. I figure someone could use the woofer-cone / voice-coil to re-cone a speaker.This is only LF unit as shown in the photos. There is no damage to the voice-coil, no burn spots et cetera. Selling for spares as I am selling my Tannoy System 600s, so no longer needed. Damaged HF unit is also available, please see my other listings.

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS A PAINTABLE GRILL AND ITS BLACK COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS A PAINTABLE GRILL WITH A CUTOUT TEMPLATE AND ITS BLACK COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS A PAINTABLE GRILL WITH A CUTOUT TEMPLATE AND ITS BLACK COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS A PAINTABLE GRILL AND ITS BLACK COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS A PAINTABLE GRILL WITH CUTOUT TEMPLATE AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg) On Jun-14-24 at 08:00:00 PDT, seller added the following information: MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE.

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THE SUPER TWEETER IS SLIGHTLY DIMPLED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS ITS WALL CLAMPS INTACT, THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS HAD SCREWS DRIVEN THROUGH THE FRAME TO INSTALL BEFORE, THERE HAS BEEN A SMALL HOLE REPAIRED IN THE DUAL CONCENTRIC DRIVER, THE WALL CLAMPS ARE MISSING, THE SUPER TWEETER IS DAMAGED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS WHITE COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

TESTED WORKING USED TANNOYs FLAGSHIP MODEL IW62-TDC DUAL CONCENTRIC IN WALL SPEAKER SYSTEM WITH A MASSIVE CROSSOVER, D.C. DRIVER #1719, SUB DRIVER #1727 AND A SUPER TWEETER. ORIGINAL BOX AND FOAM PACKING WHICH IS A LITTLE ROUGH. I HAVE 7 OF THESE IM LISTING TODAY SO CHECK OUT MY OTHERS. THIS ONE HAS HAD ITS FRAME CHOPPED OFF ON THE ENDS, THE WALL CLAMPS ARE MISSING, THE SUPER TWEETER IS DAMAGED BUT I THINK IT STILL WORKS FINE (my old ears arent good for high freq), THERE IS NO GRILL AND ITS BLACK COLOR BUT CAN BE PAINTED TO MATCH ANY COLOR. MANUALS, DOCUMENTATION, INSTALLATION DIRECTIONS AND SPECIFICATIONS AVAILABLE FOR DOWNLOAD ON THEIR WEBSITE. COPIED FROM THE WEB: The iW 62 TDC is Tannoy flagship in-wall speaker in the iW series, combining the abilities and performances of the latest Dual Concentric driver technology, a SuperTweer and an auxiliary bass driver for extended low frequency response. Using a large format chassis built from UV stabilized ABS, the iW 62 TDC leverages the performance of the class-leading iW 6 TDC and adds a second 6.50” (165 mm) bass driver for astounding bass response down to 35Hz.Solidly built and capable of withstanding continuous 120Watts RMS power handling and short term peaks up to four times that power, the iW 6 TDC’s high efficiency design (92dB/Watt) means it is capable of exceptional high peak SPL and outstanding dynamic range. For fine tuning the speaker performance to the room a front mounted switch gives +/- 1.5dB adjustment on the HF output energy.High-end features include the ability to bi-wire or bi-amplify the iW 62 TDC for peak audio performance using the dual pairs of gold plated spring terminals and Tannoy’s unique fifth terminal to ground the driver chassis. This reduces RF in the system, which can reduce the potential for hum and improve sound quality. Eight of Tannoy’s unique self-aligning clamps are used to fit the iW 62 TDC rigidly into the wall cavity, creating a solid and stable platform for the drivers.The iW 62 TDC is a genuine full range in-wall loudspeaker with a linear response from 34Hz to 51kHz, and Tannoy’s renowned sound quality. Ideally suited to larger to larger installations where higher power output is required, the iW 6 TDC offers premium performance for home theatre or multi-room distributed audio systems. Supplied with a white paintable grille and comprehensive fitting instructions, the iW 62 TDC is Tannoy’s flagship iW series in-wall loudspeaker. Super Tweeter - 1 (25mm) Titanium DomeDual Concentric™ - 1 (25 mm) Titanium Dome: - 6.5 (165 mm) mid / bassLow frequency - 6.5 (165mm) bass driverWide dispersionSuperb vocal intelligibilityOptional low insertion loss 60W line transformer for a more powerful and dynamic performanceMoulded ABS baffle for structural integrity8 clamp mounting systemQuick and easy installation Performance System Type In-Wall Loudspeaker Frequency Response (1) 70Hz - 51kHz (+/- 3dB)Low Frequency Alignment (2) 34Hz (- 6dB) Recommended Amplifier Power 20 – 210 Watts @ 8 ohms Power Handling (3) (Average) 105 Watts; (Programme) 210 Watts; (Peak) 420 Watts Sensitivity 2.38 Volts @ 1 metre (1) 92dB (Anechoic); 95dB (Half Space) Maximum SPL @ 1 metre (4)(Average) 112dB; (Peak) 118dB Impedance 8 ohm Drive Unit Dispersion 90?Driver Complement Titanium Tweeter: 1 (25mm); Dual Concentric: 6.50 (165mm); Bass Driver: 6.50 (165mm) Crossover Frequency 750Hz, 1.8kHz, 16kHz Type Passive Optional THP 60 Transformer Maximum SPL (4)107dB Wattage Tap Selections 60, 30, 15, 7.5 Watts Construction Finish White – paintable Connectors Gold Plated Spring Terminals Accessories Pre-Installation Ring, Back Can, Back Can with 60 Watt Transformer Dimensions (H x W) Mounting Depth 3.89 (99mm) Cut-out Dimensions 16.76 (426.1mm) x 7.39 (187.6mm) Font Baffle 18.64 (473.5mm) x 8.94 (227mm) Weight 11 lbs (5kg)

PAIR Tannoy 2046 speakers with crossovers. All drivers and crossovers are in excellent working condition. These 2046 drivers andcrossovers were removed from CMS8 ceiling speakers. The 2046 was also used in the legendary system 800 studio monitor(different crossover). I have another set of these in a separate listing.

PAIR Tannoy 2046 speakers with crossovers. All drivers and crossovers are in excellent working condition. These 2046 drivers andcrossovers were removed from CMS8 ceiling speakers. The 2046 was also used in the legendary system 800 studio monitor(different crossover). I have another set of these in a separate listing.

Die Tannoy 10 DTM II sind im Studio als Monitore verwendet worden. Es gibt auf den Fotos Gebrauchtspuren zu sehen.Die Coax Lautsprecher bilden besonders gut das ganze Frequenzspektrum links-rechts, stereo Abbildung.

CVS 6 General Signaling Equipment 100 V: 15, 30, 60 Watt 70.7 V: 7.5, 15, 30, 60 Watt 6 Ohm, 120 Watt Control no: 3LNE

CVS 6 General Signaling Equipment 100 V: 15, 30, 60 Watt 70.7 V: 7.5, 15, 30, 60 Watt 6 Ohm, 120 Watt Control no: 3LNE

CVS 6 General Signaling Equipment 100 V: 15, 30, 60 Watt 70.7 V: 7.5, 15, 30, 60 Watt 6 Ohm, 120 Watt Control no: 3LNE

CVS 6 General Signaling Equipment 100 V: 15, 30, 60 Watt 70.7 V: 7.5, 15, 30, 60 Watt 6 Ohm, 120 Watt Control no: 3LNE